OMAP3: Add a helper function to set timings in SDRC

Since we go through the sequence to setup the SDRC timings more than
once, break this logic out into its own function and have that function
call mem_ok() to make sure the memory is usable.

Signed-off-by: Tom Rini <trini@ti.com>

1 files changed, 61 insertions, 55 deletions

diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
index 66ce33f785..2756024caf 100644
--- a/arch/arm/cpu/armv7/omap3/sdrc.c
+++ b/arch/arm/cpu/armv7/omap3/sdrc.c
@@ -108,14 +108,45 @@ u32 get_sdr_cs_offset(u32 cs)
 }
 
 /*
+ * write_sdrc_timings -
+ *  - Takes CS and associated timings and initalize SDRAM
+ *  - Test CS to make sure it's OK for use
+ */
+static void write_sdrc_timings(u32 cs, struct sdrc_actim *sdrc_actim_base,
+		u32 mcfg, u32 ctrla, u32 ctrlb, u32 rfr_ctrl, u32 mr)
+{
+	/* Setup timings we got from the board. */
+	writel(mcfg, &sdrc_base->cs[cs].mcfg);
+	writel(ctrla, &sdrc_actim_base->ctrla);
+	writel(ctrlb, &sdrc_actim_base->ctrlb);
+	writel(rfr_ctrl, &sdrc_base->cs[cs].rfr_ctrl);
+	writel(CMD_NOP, &sdrc_base->cs[cs].manual);
+	writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
+	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+	writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+	writel(mr, &sdrc_base->cs[cs].mr);
+
+	/*
+	 * Test ram in this bank
+	 * Disable if bad or not present
+	 */
+	if (!mem_ok(cs))
+		writel(0, &sdrc_base->cs[cs].mcfg);
+}
+
+/*
  * do_sdrc_init -
- *  - Initialize the SDRAM for use.
- *  - code called once in C-Stack only context for CS0 and a possible 2nd
- *    time depending on memory configuration from stack+global context
+ *  - Code called once in C-Stack only context for CS0 and with early being
+ *    true and a possible 2nd time depending on memory configuration from
+ *    stack+global context.
  */
 void do_sdrc_init(u32 cs, u32 early)
 {
 	struct sdrc_actim *sdrc_actim_base0, *sdrc_actim_base1;
+	u32 mcfg, ctrla, ctrlb, rfr_ctrl, mr;
+
+	sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
+	sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
 
 	if (early) {
 		/* reset sdrc controller */
@@ -127,73 +158,48 @@ void do_sdrc_init(u32 cs, u32 early)
 		/* setup sdrc to ball mux */
 		writel(SDRC_SHARING, &sdrc_base->sharing);
 
-		/* Disable Power Down of CKE cuz of 1 CKE on combo part */
+		/* Disable Power Down of CKE because of 1 CKE on combo part */
 		writel(WAKEUPPROC | SRFRONRESET | PAGEPOLICY_HIGH,
 				&sdrc_base->power);
 
 		writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
 		sdelay(0x20000);
-	}
-
 /* As long as V_MCFG and V_RFR_CTRL is not defined for all OMAP3 boards we need
  * to prevent this to be build in non-SPL build */
 #ifdef CONFIG_SPL_BUILD
-	/* If we use a SPL there is no x-loader nor config header so we have
-	 * to do the job ourselfs
-	 */
-	if (cs == CS0) {
-		sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
-
-		/* General SDRC config */
-		writel(V_MCFG, &sdrc_base->cs[cs].mcfg);
-		writel(V_RFR_CTRL, &sdrc_base->cs[cs].rfr_ctrl);
-
-		/* AC timings */
-		writel(V_ACTIMA_165, &sdrc_actim_base0->ctrla);
-		writel(V_ACTIMB_165, &sdrc_actim_base0->ctrlb);
-
-		/* Initialize */
-		writel(CMD_NOP, &sdrc_base->cs[cs].manual);
-		writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
-		writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-		writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+		/*
+		 * If we use a SPL there is no x-loader nor config header so
+		 * we have to do the job ourselfs
+		 */
+
+		mcfg = V_MCFG;
+		ctrla = V_ACTIMA_165;
+		ctrlb = V_ACTIMB_165;
+		rfr_ctrl = V_RFR_CTRL;
+		mr = V_MR;
+
+		write_sdrc_timings(CS0, sdrc_actim_base0, mcfg, ctrla, ctrlb,
+				rfr_ctrl, mr);
+#endif
 
-		writel(V_MR, &sdrc_base->cs[cs].mr);
 	}
-#endif
 
 	/*
-	 * SDRC timings are set up by x-load or config header
-	 * We don't need to redo them here.
-	 * Older x-loads configure only CS0
-	 * configure CS1 to handle this ommission
+	 * If we aren't using SPL we have been loaded by some
+	 * other means which may not have correctly initialized
+	 * both CS0 and CS1 (such as some older versions of x-loader)
+	 * so we may be asked now to setup CS1.
 	 */
 	if (cs == CS1) {
-		sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
-		sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
-		writel(readl(&sdrc_base->cs[CS0].mcfg),
-			&sdrc_base->cs[CS1].mcfg);
-		writel(readl(&sdrc_base->cs[CS0].rfr_ctrl),
-			&sdrc_base->cs[CS1].rfr_ctrl);
-		writel(readl(&sdrc_actim_base0->ctrla),
-			&sdrc_actim_base1->ctrla);
-		writel(readl(&sdrc_actim_base0->ctrlb),
-			&sdrc_actim_base1->ctrlb);
-
-		writel(CMD_NOP, &sdrc_base->cs[cs].manual);
-		writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
-		writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-		writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
-		writel(readl(&sdrc_base->cs[CS0].mr),
-			&sdrc_base->cs[CS1].mr);
-	}
+		mcfg = readl(&sdrc_base->cs[CS0].mcfg),
+		rfr_ctrl = readl(&sdrc_base->cs[CS0].rfr_ctrl);
+		ctrla = readl(&sdrc_actim_base0->ctrla),
+		ctrlb = readl(&sdrc_actim_base0->ctrlb);
+		mr = readl(&sdrc_base->cs[CS0].mr);
+		write_sdrc_timings(cs, sdrc_actim_base1, mcfg, ctrla, ctrlb,
+				rfr_ctrl, mr);
 
-	/*
-	 * Test ram in this bank
-	 * Disable if bad or not present
-	 */
-	if (!mem_ok(cs))
-		writel(0, &sdrc_base->cs[cs].mcfg);
+	}
 }
 
 /*