Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

11 files changed, 313 insertions, 165 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 22f0f09af6..f933123395 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -424,6 +424,9 @@ config OMAP54XX
 config RMOBILE
 	bool "Renesas ARM SoCs"
 
+config TARGET_CM_FX6
+	bool "Support cm_fx6"
+
 config TARGET_S5P_GONI
 	bool "Support s5p_goni"
 
@@ -579,6 +582,7 @@ source "board/cirrus/edb93xx/Kconfig"
 source "board/cm4008/Kconfig"
 source "board/cm41xx/Kconfig"
 source "board/compulab/cm_t335/Kconfig"
+source "board/compulab/cm_fx6/Kconfig"
 source "board/congatec/cgtqmx6eval/Kconfig"
 source "board/creative/xfi3/Kconfig"
 source "board/davedenx/qong/Kconfig"
diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c
index 820b8d5154..336e557a27 100644
--- a/arch/arm/cpu/armv7/mx6/clock.c
+++ b/arch/arm/cpu/armv7/mx6/clock.c
@@ -36,6 +36,35 @@ void enable_ocotp_clk(unsigned char enable)
 }
 #endif
 
+#ifdef CONFIG_NAND_MXS
+void setup_gpmi_io_clk(u32 cfg)
+{
+	/* Disable clocks per ERR007177 from MX6 errata */
+	clrbits_le32(&imx_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+	clrbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+	clrsetbits_le32(&imx_ccm->cs2cdr,
+			MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+			cfg);
+
+	setbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+	setbits_le32(&imx_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+}
+#endif
+
 void enable_usboh3_clk(unsigned char enable)
 {
 	u32 reg;
@@ -49,6 +78,67 @@ void enable_usboh3_clk(unsigned char enable)
 
 }
 
+#if defined(CONFIG_FEC_MXC) && !defined(CONFIG_MX6SX)
+void enable_enet_clk(unsigned char enable)
+{
+	u32 mask = MXC_CCM_CCGR1_ENET_CLK_ENABLE_MASK;
+
+	if (enable)
+		setbits_le32(&imx_ccm->CCGR1, mask);
+	else
+		clrbits_le32(&imx_ccm->CCGR1, mask);
+}
+#endif
+
+#ifdef CONFIG_MXC_UART
+void enable_uart_clk(unsigned char enable)
+{
+	u32 mask = MXC_CCM_CCGR5_UART_MASK | MXC_CCM_CCGR5_UART_SERIAL_MASK;
+
+	if (enable)
+		setbits_le32(&imx_ccm->CCGR5, mask);
+	else
+		clrbits_le32(&imx_ccm->CCGR5, mask);
+}
+#endif
+
+#ifdef CONFIG_SPI
+/* spi_num can be from 0 - 4 */
+int enable_cspi_clock(unsigned char enable, unsigned spi_num)
+{
+	u32 mask;
+
+	if (spi_num > 4)
+		return -EINVAL;
+
+	mask = MXC_CCM_CCGR_CG_MASK << (spi_num * 2);
+	if (enable)
+		setbits_le32(&imx_ccm->CCGR1, mask);
+	else
+		clrbits_le32(&imx_ccm->CCGR1, mask);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MMC
+int enable_usdhc_clk(unsigned char enable, unsigned bus_num)
+{
+	u32 mask;
+
+	if (bus_num > 3)
+		return -EINVAL;
+
+	mask = MXC_CCM_CCGR_CG_MASK << (bus_num * 2 + 2);
+	if (enable)
+		setbits_le32(&imx_ccm->CCGR6, mask);
+	else
+		clrbits_le32(&imx_ccm->CCGR6, mask);
+
+	return 0;
+}
+#endif
+
 #ifdef CONFIG_SYS_I2C_MXC
 /* i2c_num can be from 0 - 2 */
 int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
@@ -509,6 +599,7 @@ int enable_pcie_clock(void)
 	struct anatop_regs *anatop_regs =
 		(struct anatop_regs *)ANATOP_BASE_ADDR;
 	struct mxc_ccm_reg *ccm_regs = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	u32 lvds1_clk_sel;
 
 	/*
 	 * Here be dragons!
@@ -518,17 +609,25 @@ int enable_pcie_clock(void)
 	 * marked as ANATOP_MISC1 is actually documented in the PMU section
 	 * of the datasheet as PMU_MISC1.
 	 *
-	 * Switch LVDS clock source to SATA (0xb), disable clock INPUT and
-	 * enable clock OUTPUT. This is important for PCI express link that
-	 * is clocked from the i.MX6.
+	 * Switch LVDS clock source to SATA (0xb) on mx6q/dl or PCI (0xa) on
+	 * mx6sx, disable clock INPUT and enable clock OUTPUT. This is important
+	 * for PCI express link that is clocked from the i.MX6.
 	 */
 #define ANADIG_ANA_MISC1_LVDSCLK1_IBEN		(1 << 12)
 #define ANADIG_ANA_MISC1_LVDSCLK1_OBEN		(1 << 10)
 #define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK	0x0000001F
+#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF	0xa
+#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF	0xb
+
+	if (is_cpu_type(MXC_CPU_MX6SX))
+		lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF;
+	else
+		lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF;
+
 	clrsetbits_le32(&anatop_regs->ana_misc1,
 			ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
 			ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
-			ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
+			ANADIG_ANA_MISC1_LVDSCLK1_OBEN | lvds1_clk_sel);
 
 	/* PCIe reference clock sourced from AXI. */
 	clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL);
diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c
index 1ab69f63c8..7b5c1e4dd7 100644
--- a/arch/arm/cpu/armv7/mx6/ddr.c
+++ b/arch/arm/cpu/armv7/mx6/ddr.c
@@ -184,18 +184,18 @@ void mx6sdl_dram_iocfg(unsigned width,
  */
 #define MR(val, ba, cmd, cs1) \
 	((val << 16) | (1 << 15) | (cmd << 4) | (cs1 << 3) | ba)
-void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
-		  const struct mx6_mmdc_calibration *c,
-		  const struct mx6_ddr3_cfg *m)
+void mx6_dram_cfg(const struct mx6_ddr_sysinfo *sysinfo,
+		  const struct mx6_mmdc_calibration *calib,
+		  const struct mx6_ddr3_cfg *ddr3_cfg)
 {
 	volatile struct mmdc_p_regs *mmdc0;
 	volatile struct mmdc_p_regs *mmdc1;
-	u32 reg;
+	u32 val;
 	u8 tcke, tcksrx, tcksre, txpdll, taofpd, taonpd, trrd;
 	u8 todtlon, taxpd, tanpd, tcwl, txp, tfaw, tcl;
 	u8 todt_idle_off = 0x4; /* from DDR3 Script Aid spreadsheet */
 	u16 trcd, trc, tras, twr, tmrd, trtp, trp, twtr, trfc, txs, txpr;
-	u16 CS0_END;
+	u16 cs0_end;
 	u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */
 	u8 coladdr;
 	int clkper; /* clock period in picoseconds */
@@ -215,13 +215,12 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
 		clock = 400;
 		tcwl = 3;
 	}
-	clkper = (1000*1000)/clock; /* ps */
+	clkper = (1000 * 1000) / clock; /* pico seconds */
 	todtlon = tcwl;
 	taxpd = tcwl;
 	tanpd = tcwl;
-	tcwl = tcwl;
 
-	switch (m->density) {
+	switch (ddr3_cfg->density) {
 	case 1: /* 1Gb per chip */
 		trfc = DIV_ROUND_UP(110000, clkper) - 1;
 		txs = DIV_ROUND_UP(120000, clkper) - 1;
@@ -240,80 +239,82 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
 		break;
 	default:
 		/* invalid density */
-		printf("invalid chip density\n");
+		puts("invalid chip density\n");
 		hang();
 		break;
 	}
 	txpr = txs;
 
-	switch (m->mem_speed) {
+	switch (ddr3_cfg->mem_speed) {
 	case 800:
-		txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
-		tcke = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
-		if (m->pagesz == 1) {
+		txp = DIV_ROUND_UP(MAX(3 * clkper, 7500), clkper) - 1;
+		tcke = DIV_ROUND_UP(MAX(3 * clkper, 7500), clkper) - 1;
+		if (ddr3_cfg->pagesz == 1) {
 			tfaw = DIV_ROUND_UP(40000, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 10000), clkper) - 1;
 		} else {
 			tfaw = DIV_ROUND_UP(50000, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 10000), clkper) - 1;
 		}
 		break;
 	case 1066:
-		txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
-		tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
-		if (m->pagesz == 1) {
+		txp = DIV_ROUND_UP(MAX(3 * clkper, 7500), clkper) - 1;
+		tcke = DIV_ROUND_UP(MAX(3 * clkper, 5625), clkper) - 1;
+		if (ddr3_cfg->pagesz == 1) {
 			tfaw = DIV_ROUND_UP(37500, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 7500), clkper) - 1;
 		} else {
 			tfaw = DIV_ROUND_UP(50000, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 10000), clkper) - 1;
 		}
 		break;
 	case 1333:
-		txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
-		tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
-		if (m->pagesz == 1) {
+		txp = DIV_ROUND_UP(MAX(3 * clkper, 6000), clkper) - 1;
+		tcke = DIV_ROUND_UP(MAX(3 * clkper, 5625), clkper) - 1;
+		if (ddr3_cfg->pagesz == 1) {
 			tfaw = DIV_ROUND_UP(30000, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 6000), clkper) - 1;
 		} else {
 			tfaw = DIV_ROUND_UP(45000, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 7500), clkper) - 1;
 		}
 		break;
 	case 1600:
-		txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
-		tcke = DIV_ROUND_UP(MAX(3*clkper, 5000), clkper) - 1;
-		if (m->pagesz == 1) {
+		txp = DIV_ROUND_UP(MAX(3 * clkper, 6000), clkper) - 1;
+		tcke = DIV_ROUND_UP(MAX(3 * clkper, 5000), clkper) - 1;
+		if (ddr3_cfg->pagesz == 1) {
 			tfaw = DIV_ROUND_UP(30000, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 6000), clkper) - 1;
 		} else {
 			tfaw = DIV_ROUND_UP(40000, clkper) - 1;
-			trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+			trrd = DIV_ROUND_UP(MAX(4 * clkper, 7500), clkper) - 1;
 		}
 		break;
 	default:
-		printf("invalid memory speed\n");
+		puts("invalid memory speed\n");
 		hang();
 		break;
 	}
-	txpdll = DIV_ROUND_UP(MAX(10*clkper, 24000), clkper) - 1;
-	tcl = DIV_ROUND_UP(m->trcd, clkper/10) - 3;
-	tcksre = DIV_ROUND_UP(MAX(5*clkper, 10000), clkper);
-	tcksrx = tcksre;
+	txpdll = DIV_ROUND_UP(MAX(10 * clkper, 24000), clkper) - 1;
+	tcksre = DIV_ROUND_UP(MAX(5 * clkper, 10000), clkper);
 	taonpd = DIV_ROUND_UP(2000, clkper) - 1;
+	tcksrx = tcksre;
 	taofpd = taonpd;
-	trp = DIV_ROUND_UP(m->trcd, clkper/10) - 1;
+	twr  = DIV_ROUND_UP(15000, clkper) - 1;
+	tmrd = DIV_ROUND_UP(MAX(12 * clkper, 15000), clkper) - 1;
+	trc  = DIV_ROUND_UP(ddr3_cfg->trcmin, clkper / 10) - 1;
+	tras = DIV_ROUND_UP(ddr3_cfg->trasmin, clkper / 10) - 1;
+	tcl  = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 3;
+	trp  = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 1;
+	twtr = ROUND(MAX(4 * clkper, 7500) / clkper, 1) - 1;
 	trcd = trp;
-	trc = DIV_ROUND_UP(m->trcmin, clkper/10) - 1;
-	tras = DIV_ROUND_UP(m->trasmin, clkper/10) - 1;
-	twr = DIV_ROUND_UP(15000, clkper) - 1;
-	tmrd = DIV_ROUND_UP(MAX(12*clkper, 15000), clkper) - 1;
-	twtr = ROUND(MAX(4*clkper, 7500)/clkper, 1) - 1;
 	trtp = twtr;
-	CS0_END = ((4*i->cs_density) <= 120) ? (4*i->cs_density)+7 : 127;
-	debug("density:%d Gb (%d Gb per chip)\n", i->cs_density, m->density);
+	cs0_end = 4 * sysinfo->cs_density - 1;
+
+	debug("density:%d Gb (%d Gb per chip)\n",
+	      sysinfo->cs_density, ddr3_cfg->density);
 	debug("clock: %dMHz (%d ps)\n", clock, clkper);
-	debug("memspd:%d\n", m->mem_speed);
+	debug("memspd:%d\n", ddr3_cfg->mem_speed);
 	debug("tcke=%d\n", tcke);
 	debug("tcksrx=%d\n", tcksrx);
 	debug("tcksre=%d\n", tcksre);
@@ -340,11 +341,11 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
 	debug("twtr=%d\n", twtr);
 	debug("trrd=%d\n", trrd);
 	debug("txpr=%d\n", txpr);
-	debug("CS0_END=%d\n", CS0_END);
-	debug("ncs=%d\n", i->ncs);
-	debug("Rtt_wr=%d\n", i->rtt_wr);
-	debug("Rtt_nom=%d\n", i->rtt_nom);
-	debug("SRT=%d\n", m->SRT);
+	debug("cs0_end=%d\n", cs0_end);
+	debug("ncs=%d\n", sysinfo->ncs);
+	debug("Rtt_wr=%d\n", sysinfo->rtt_wr);
+	debug("Rtt_nom=%d\n", sysinfo->rtt_nom);
+	debug("SRT=%d\n", ddr3_cfg->SRT);
 	debug("tcl=%d\n", tcl);
 	debug("twr=%d\n", twr);
 
@@ -354,142 +355,136 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
 	 *  see:
 	 *   appnote, ddr3 spreadsheet
 	 */
-	mmdc0->mpwldectrl0 = c->p0_mpwldectrl0;
-	mmdc0->mpwldectrl1 = c->p0_mpwldectrl1;
-	mmdc0->mpdgctrl0 = c->p0_mpdgctrl0;
-	mmdc0->mpdgctrl1 = c->p0_mpdgctrl1;
-	mmdc0->mprddlctl = c->p0_mprddlctl;
-	mmdc0->mpwrdlctl = c->p0_mpwrdlctl;
-	if (i->dsize > 1) {
-		mmdc1->mpwldectrl0 = c->p1_mpwldectrl0;
-		mmdc1->mpwldectrl1 = c->p1_mpwldectrl1;
-		mmdc1->mpdgctrl0 = c->p1_mpdgctrl0;
-		mmdc1->mpdgctrl1 = c->p1_mpdgctrl1;
-		mmdc1->mprddlctl = c->p1_mprddlctl;
-		mmdc1->mpwrdlctl = c->p1_mpwrdlctl;
+	mmdc0->mpwldectrl0 = calib->p0_mpwldectrl0;
+	mmdc0->mpwldectrl1 = calib->p0_mpwldectrl1;
+	mmdc0->mpdgctrl0 = calib->p0_mpdgctrl0;
+	mmdc0->mpdgctrl1 = calib->p0_mpdgctrl1;
+	mmdc0->mprddlctl = calib->p0_mprddlctl;
+	mmdc0->mpwrdlctl = calib->p0_mpwrdlctl;
+	if (sysinfo->dsize > 1) {
+		mmdc1->mpwldectrl0 = calib->p1_mpwldectrl0;
+		mmdc1->mpwldectrl1 = calib->p1_mpwldectrl1;
+		mmdc1->mpdgctrl0 = calib->p1_mpdgctrl0;
+		mmdc1->mpdgctrl1 = calib->p1_mpdgctrl1;
+		mmdc1->mprddlctl = calib->p1_mprddlctl;
+		mmdc1->mpwrdlctl = calib->p1_mpwrdlctl;
 	}
 
 	/* Read data DQ Byte0-3 delay */
-	mmdc0->mprddqby0dl = (u32)0x33333333;
-	mmdc0->mprddqby1dl = (u32)0x33333333;
-	if (i->dsize > 0) {
-		mmdc0->mprddqby2dl = (u32)0x33333333;
-		mmdc0->mprddqby3dl = (u32)0x33333333;
+	mmdc0->mprddqby0dl = 0x33333333;
+	mmdc0->mprddqby1dl = 0x33333333;
+	if (sysinfo->dsize > 0) {
+		mmdc0->mprddqby2dl = 0x33333333;
+		mmdc0->mprddqby3dl = 0x33333333;
 	}
-	if (i->dsize > 1) {
-		mmdc1->mprddqby0dl = (u32)0x33333333;
-		mmdc1->mprddqby1dl = (u32)0x33333333;
-		mmdc1->mprddqby2dl = (u32)0x33333333;
-		mmdc1->mprddqby3dl = (u32)0x33333333;
+
+	if (sysinfo->dsize > 1) {
+		mmdc1->mprddqby0dl = 0x33333333;
+		mmdc1->mprddqby1dl = 0x33333333;
+		mmdc1->mprddqby2dl = 0x33333333;
+		mmdc1->mprddqby3dl = 0x33333333;
 	}
 
 	/* MMDC Termination: rtt_nom:2 RZQ/2(120ohm), rtt_nom:1 RZQ/4(60ohm) */
-	reg = (i->rtt_nom == 2) ? 0x00011117 : 0x00022227;
-	mmdc0->mpodtctrl = reg;
-	if (i->dsize > 1)
-		mmdc1->mpodtctrl = reg;
+	val = (sysinfo->rtt_nom == 2) ? 0x00011117 : 0x00022227;
+	mmdc0->mpodtctrl = val;
+	if (sysinfo->dsize > 1)
+		mmdc1->mpodtctrl = val;
 
 	/* complete calibration */
-	reg = (1 << 11); /* Force measurement on delay-lines */
-	mmdc0->mpmur0 = reg;
-	if (i->dsize > 1)
-		mmdc1->mpmur0 = reg;
+	val = (1 << 11); /* Force measurement on delay-lines */
+	mmdc0->mpmur0 = val;
+	if (sysinfo->dsize > 1)
+		mmdc1->mpmur0 = val;
 
 	/* Step 1: configuration request */
 	mmdc0->mdscr = (u32)(1 << 15); /* config request */
 
 	/* Step 2: Timing configuration */
-	reg = (trfc << 24) | (txs << 16) | (txp << 13) | (txpdll << 9) |
-	      (tfaw << 4) | tcl;
-	mmdc0->mdcfg0 = reg;
-	reg = (trcd << 29) | (trp << 26) | (trc << 21) | (tras << 16) |
-	      (1 << 15) |		/* trpa */
-	      (twr << 9) | (tmrd << 5) | tcwl;
-	mmdc0->mdcfg1 = reg;
-	reg = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd;
-	mmdc0->mdcfg2 = reg;
-	reg = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) | (taxpd << 16) |
-	      (todtlon << 12) | (todt_idle_off << 4);
-	mmdc0->mdotc = reg;
-	mmdc0->mdasp = CS0_END; /* CS addressing */
+	mmdc0->mdcfg0 = (trfc << 24) | (txs << 16) | (txp << 13) |
+			(txpdll << 9) | (tfaw << 4) | tcl;
+	mmdc0->mdcfg1 = (trcd << 29) | (trp << 26) | (trc << 21) |
+			(tras << 16) | (1 << 15) /* trpa */ |
+			(twr << 9) | (tmrd << 5) | tcwl;
+	mmdc0->mdcfg2 = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd;
+	mmdc0->mdotc = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) |
+		       (taxpd << 16) | (todtlon << 12) | (todt_idle_off << 4);
+	mmdc0->mdasp = cs0_end; /* CS addressing */
 
 	/* Step 3: Configure DDR type */
-	reg = (i->cs1_mirror << 19) | (i->walat << 16) | (i->bi_on << 12) |
-	      (i->mif3_mode << 9) | (i->ralat << 6);
-	mmdc0->mdmisc = reg;
+	mmdc0->mdmisc = (sysinfo->cs1_mirror << 19) | (sysinfo->walat << 16) |
+			(sysinfo->bi_on << 12) | (sysinfo->mif3_mode << 9) |
+			(sysinfo->ralat << 6);
 
 	/* Step 4: Configure delay while leaving reset */
-	reg = (txpr << 16) | (i->sde_to_rst << 8) | (i->rst_to_cke << 0);
-	mmdc0->mdor = reg;
+	mmdc0->mdor = (txpr << 16) | (sysinfo->sde_to_rst << 8) |
+		      (sysinfo->rst_to_cke << 0);
 
 	/* Step 5: Configure DDR physical parameters (density and burst len) */
-	coladdr = m->coladdr;
-	if (m->coladdr == 8)		/* 8-bit COL is 0x3 */
+	coladdr = ddr3_cfg->coladdr;
+	if (ddr3_cfg->coladdr == 8)		/* 8-bit COL is 0x3 */
 		coladdr += 4;
-	else if (m->coladdr == 12)	/* 12-bit COL is 0x4 */
+	else if (ddr3_cfg->coladdr == 12)	/* 12-bit COL is 0x4 */
 		coladdr += 1;
-	reg = (m->rowaddr - 11) << 24 |		/* ROW */
-	      (coladdr - 9) << 20 |		/* COL */
-	      (1 << 19) |			/* Burst Length = 8 for DDR3 */
-	      (i->dsize << 16);			/* DDR data bus size */
-	mmdc0->mdctl = reg;
+	mmdc0->mdctl =  (ddr3_cfg->rowaddr - 11) << 24 |	/* ROW */
+			(coladdr - 9) << 20 |			/* COL */
+			(1 << 19) |		/* Burst Length = 8 for DDR3 */
+			(sysinfo->dsize << 16);		/* DDR data bus size */
 
 	/* Step 6: Perform ZQ calibration */
-	reg = (u32)0xa1390001; /* one-time HW ZQ calib */
-	mmdc0->mpzqhwctrl = reg;
-	if (i->dsize > 1)
-		mmdc1->mpzqhwctrl = reg;
+	val = 0xa1390001; /* one-time HW ZQ calib */
+	mmdc0->mpzqhwctrl = val;
+	if (sysinfo->dsize > 1)
+		mmdc1->mpzqhwctrl = val;
 
 	/* Step 7: Enable MMDC with desired chip select */
-	reg = mmdc0->mdctl |
-	      (1 << 31) |			/* SDE_0 for CS0 */
-	      ((i->ncs == 2) ? 1 : 0) << 30;	/* SDE_1 for CS1 */
-	mmdc0->mdctl = reg;
+	mmdc0->mdctl |= (1 << 31) |			     /* SDE_0 for CS0 */
+			((sysinfo->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */
 
 	/* Step 8: Write Mode Registers to Init DDR3 devices */
-	for (cs = 0; cs < i->ncs; cs++) {
+	for (cs = 0; cs < sysinfo->ncs; cs++) {
 		/* MR2 */
-		reg = (i->rtt_wr & 3) << 9 | (m->SRT & 1) << 7 |
+		val = (sysinfo->rtt_wr & 3) << 9 | (ddr3_cfg->SRT & 1) << 7 |
 		      ((tcwl - 3) & 3) << 3;
-		mmdc0->mdscr = (u32)MR(reg, 2, 3, cs);
+		mmdc0->mdscr = MR(val, 2, 3, cs);
 		/* MR3 */
-		mmdc0->mdscr = (u32)MR(0, 3, 3, cs);
+		mmdc0->mdscr = MR(0, 3, 3, cs);
 		/* MR1 */
-		reg = ((i->rtt_nom & 1) ? 1 : 0) << 2 |
-		      ((i->rtt_nom & 2) ? 1 : 0) << 6;
-		mmdc0->mdscr = (u32)MR(reg, 1, 3, cs);
-		reg = ((tcl - 1) << 4) |	/* CAS */
+		val = ((sysinfo->rtt_nom & 1) ? 1 : 0) << 2 |
+		      ((sysinfo->rtt_nom & 2) ? 1 : 0) << 6;
+		mmdc0->mdscr = MR(val, 1, 3, cs);
+		/* MR0 */
+		val = ((tcl - 1) << 4) |	/* CAS */
 		      (1 << 8)   |		/* DLL Reset */
 		      ((twr - 3) << 9);		/* Write Recovery */
-		/* MR0 */
-		mmdc0->mdscr = (u32)MR(reg, 0, 3, cs);
+		mmdc0->mdscr = MR(val, 0, 3, cs);
 		/* ZQ calibration */
-		reg = (1 << 10);
-		mmdc0->mdscr = (u32)MR(reg, 0, 4, cs);
+		val = (1 << 10);
+		mmdc0->mdscr = MR(val, 0, 4, cs);
 	}
 
 	/* Step 10: Power down control and self-refresh */
-	reg = (tcke & 0x7) << 16 |
-	      5            << 12 |  /* PWDT_1: 256 cycles */
-	      5            <<  8 |  /* PWDT_0: 256 cycles */
-	      1            <<  6 |  /* BOTH_CS_PD */
-	      (tcksrx & 0x7) << 3 |
-	      (tcksre & 0x7);
-	mmdc0->mdpdc = reg;
-	mmdc0->mapsr = (u32)0x00011006; /* ADOPT power down enabled */
+	mmdc0->mdpdc = (tcke & 0x7) << 16 |
+			5            << 12 |  /* PWDT_1: 256 cycles */
+			5            <<  8 |  /* PWDT_0: 256 cycles */
+			1            <<  7 |  /* SLOW_PD */
+			1            <<  6 |  /* BOTH_CS_PD */
+			(tcksrx & 0x7) << 3 |
+			(tcksre & 0x7);
+	mmdc0->mapsr = 0x00001006; /* ADOPT power down enabled */
 
 	/* Step 11: Configure ZQ calibration: one-time and periodic 1ms */
-	mmdc0->mpzqhwctrl = (u32)0xa1390003;
-	if (i->dsize > 1)
-		mmdc1->mpzqhwctrl = (u32)0xa1390003;
+	val = 0xa1390003;
+	mmdc0->mpzqhwctrl = val;
+	if (sysinfo->dsize > 1)
+		mmdc1->mpzqhwctrl = val;
 
 	/* Step 12: Configure and activate periodic refresh */
-	reg = (1 << 14) |	/* REF_SEL: Periodic refresh cycles of 32kHz */
-	      (7 << 11);	/* REFR: Refresh Rate - 8 refreshes */
-	mmdc0->mdref = reg;
+	mmdc0->mdref = (1 << 14) | /* REF_SEL: Periodic refresh cycle: 32kHz */
+		       (7 << 11);  /* REFR: Refresh Rate - 8 refreshes */
 
 	/* Step 13: Deassert config request - init complete */
-	mmdc0->mdscr = (u32)0x00000000;
+	mmdc0->mdscr = 0x00000000;
 
 	/* wait for auto-ZQ calibration to complete */
 	mdelay(1);
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index ac84a1fbfb..ba21cfe580 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -324,10 +324,10 @@ const struct boot_mode soc_boot_modes[] = {
 	/* reserved value should start rom usb */
 	{"usb",		MAKE_CFGVAL(0x01, 0x00, 0x00, 0x00)},
 	{"sata",	MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)},
-	{"escpi1:0",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)},
-	{"escpi1:1",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)},
-	{"escpi1:2",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)},
-	{"escpi1:3",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)},
+	{"ecspi1:0",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)},
+	{"ecspi1:1",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)},
+	{"ecspi1:2",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)},
+	{"ecspi1:3",	MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)},
 	/* 4 bit bus width */
 	{"esdhc1",	MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
 	{"esdhc2",	MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
@@ -430,6 +430,9 @@ void v7_outer_cache_enable(void)
 	}
 #endif
 
+	/* Must disable the L2 before changing the latency parameters */
+	clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+
 	writel(0x132, &pl310->pl310_tag_latency_ctrl);
 	writel(0x132, &pl310->pl310_data_latency_ctrl);
 
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 1ccd8274d2..5f2b946fdd 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -9,7 +9,6 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5420-peach-pit.dtb
-dtb-$(CONFIG_MX6) += imx6q-sabreauto.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \
diff --git a/arch/arm/dts/imx6q-sabreauto.dts b/arch/arm/dts/imx6q-sabreauto.dts
deleted file mode 100644
index 7af2a88fd0..0000000000
--- a/arch/arm/dts/imx6q-sabreauto.dts
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * SPDX-License-Identifier:     GPL-2.0+
- */
-
-/dts-v1/;
-
-/ {
-	model = "Freescale i.MX6 Quad SABRE Automotive Board";
-	compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
-};
diff --git a/arch/arm/include/asm/arch-mx6/clock.h b/arch/arm/include/asm/arch-mx6/clock.h
index 339c789110..c11674ff8a 100644
--- a/arch/arm/include/asm/arch-mx6/clock.h
+++ b/arch/arm/include/asm/arch-mx6/clock.h
@@ -52,12 +52,17 @@ enum enet_freq {
 u32 imx_get_uartclk(void);
 u32 imx_get_fecclk(void);
 unsigned int mxc_get_clock(enum mxc_clock clk);
+void setup_gpmi_io_clk(u32 cfg);
 void enable_ocotp_clk(unsigned char enable);
 void enable_usboh3_clk(unsigned char enable);
+void enable_uart_clk(unsigned char enable);
+int enable_cspi_clock(unsigned char enable, unsigned spi_num);
+int enable_usdhc_clk(unsigned char enable, unsigned bus_num);
 int enable_sata_clock(void);
 int enable_pcie_clock(void);
 int enable_i2c_clk(unsigned char enable, unsigned i2c_num);
 int enable_spi_clk(unsigned char enable, unsigned spi_num);
 void enable_ipu_clock(void);
 int enable_fec_anatop_clock(enum enet_freq freq);
+void enable_enet_clk(unsigned char enable);
 #endif /* __ASM_ARCH_CLOCK_H */
diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index 2631beb924..22614fcd0e 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -419,6 +419,19 @@ struct iomuxc {
 	u32 gpr[14];
 };
 
+struct gpc {
+	u32	cntr;
+	u32	pgr;
+	u32	imr1;
+	u32	imr2;
+	u32	imr3;
+	u32	imr4;
+	u32	isr1;
+	u32	isr2;
+	u32	isr3;
+	u32	isr4;
+};
+
 #define IOMUXC_GPR2_COUNTER_RESET_VAL_OFFSET		20
 #define IOMUXC_GPR2_COUNTER_RESET_VAL_MASK		(3<<IOMUXC_GPR2_COUNTER_RESET_VAL_OFFSET)
 #define IOMUXC_GPR2_LVDS_CLK_SHIFT_OFFSET		16
diff --git a/arch/arm/include/asm/arch-mx6/iomux.h b/arch/arm/include/asm/arch-mx6/iomux.h
index f54db6944d..9b3a91f076 100644
--- a/arch/arm/include/asm/arch-mx6/iomux.h
+++ b/arch/arm/include/asm/arch-mx6/iomux.h
@@ -19,6 +19,12 @@
 #define IOMUXC_GPR1_TEST_POWERDOWN		(1 << 18)
 
 /*
+ * IOMUXC_GPR5 bit fields
+ */
+#define IOMUXC_GPR5_PCIE_BTNRST			(1 << 19)
+#define IOMUXC_GPR5_PCIE_PERST			(1 << 18)
+
+/*
  * IOMUXC_GPR8 bit fields
  */
 #define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_MASK		(0x3f << 0)
@@ -35,12 +41,15 @@
 /*
  * IOMUXC_GPR12 bit fields
  */
+#define IOMUXC_GPR12_RX_EQ_2			(0x2 << 0)
+#define IOMUXC_GPR12_RX_EQ_MASK			(0x7 << 0)
 #define IOMUXC_GPR12_LOS_LEVEL_9		(0x9 << 4)
 #define IOMUXC_GPR12_LOS_LEVEL_MASK		(0x1f << 4)
 #define IOMUXC_GPR12_APPS_LTSSM_ENABLE		(1 << 10)
 #define IOMUXC_GPR12_DEVICE_TYPE_EP		(0x0 << 12)
 #define IOMUXC_GPR12_DEVICE_TYPE_RC		(0x4 << 12)
 #define IOMUXC_GPR12_DEVICE_TYPE_MASK		(0xf << 12)
+#define IOMUXC_GPR12_TEST_POWERDOWN		(1 << 30)
 
 /*
  * IOMUXC_GPR13 bit fields
diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h
index 306d6998ce..c35a905141 100644
--- a/arch/arm/include/asm/arch-mx6/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx6/sys_proto.h
@@ -20,8 +20,9 @@ u32 get_cpu_rev(void);
 /* returns MXC_CPU_ value */
 #define cpu_type(rev) (((rev) >> 12)&0xff)
 
-/* use with MXC_CPU_ constants */
-#define is_cpu_type(cpu) (cpu_type(get_cpu_rev()) == cpu)
+/* both macros return/take MXC_CPU_ constants */
+#define get_cpu_type()	(cpu_type(get_cpu_rev()))
+#define is_cpu_type(cpu) (get_cpu_type() == cpu)
 
 const char *get_imx_type(u32 imxtype);
 unsigned imx_ddr_size(void);
diff --git a/arch/arm/include/asm/imx-common/mxc_i2c.h b/arch/arm/include/asm/imx-common/mxc_i2c.h
index 47a9edc81b..182c2f397f 100644
--- a/arch/arm/include/asm/imx-common/mxc_i2c.h
+++ b/arch/arm/include/asm/imx-common/mxc_i2c.h
@@ -19,6 +19,39 @@ struct i2c_pads_info {
 	struct i2c_pin_ctrl sda;
 };
 
+#if defined(CONFIG_MX6QDL)
+#define I2C_PADS(name, scl_i2c, scl_gpio, scl_gp, sda_i2c, sda_gpio, sda_gp) \
+	struct i2c_pads_info mx6q_##name = {		\
+		.scl = {				\
+			.i2c_mode = MX6Q_##scl_i2c,	\
+			.gpio_mode = MX6Q_##scl_gpio,	\
+			.gp = scl_gp,			\
+		},					\
+		.sda = {				\
+			.i2c_mode = MX6Q_##sda_i2c,	\
+			.gpio_mode = MX6Q_##sda_gpio,	\
+			.gp = sda_gp,			\
+		}					\
+	};						\
+	struct i2c_pads_info mx6s_##name = {		\
+		.scl = {				\
+			.i2c_mode = MX6DL_##scl_i2c,	\
+			.gpio_mode = MX6DL_##scl_gpio,	\
+			.gp = scl_gp,			\
+		},					\
+		.sda = {				\
+			.i2c_mode = MX6DL_##sda_i2c,	\
+			.gpio_mode = MX6DL_##sda_gpio,	\
+			.gp = sda_gp,			\
+		}					\
+	};
+
+
+#define I2C_PADS_INFO(name)	\
+	(is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) ? \
+					&mx6q_##name : &mx6s_##name
+#endif
+
 void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
 		struct i2c_pads_info *p);
 void bus_i2c_init(void *base, int speed, int slave_addr,