NDS32: Generic Board Support and Unsupport

	Remove ag101 and ag102 support

Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>

9 files changed, 0 insertions, 312 deletions

diff --git a/board/AndesTech/adp-ag101/Kconfig b/board/AndesTech/adp-ag101/Kconfig
deleted file mode 100644
index 8f0197a638..0000000000
--- a/board/AndesTech/adp-ag101/Kconfig
+++ /dev/null
@@ -1,18 +0,0 @@
-if TARGET_ADP_AG101
-
-config SYS_CPU
-	default "n1213"
-
-config SYS_BOARD
-	default "adp-ag101"
-
-config SYS_VENDOR
-	default "AndesTech"
-
-config SYS_SOC
-	default "ag101"
-
-config SYS_CONFIG_NAME
-	default "adp-ag101"
-
-endif
diff --git a/board/AndesTech/adp-ag101/MAINTAINERS b/board/AndesTech/adp-ag101/MAINTAINERS
deleted file mode 100644
index 1f0169bb66..0000000000
--- a/board/AndesTech/adp-ag101/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ADP-AG101 BOARD
-M:	Andes <uboot@andestech.com>
-S:	Maintained
-F:	board/AndesTech/adp-ag101/
-F:	include/configs/adp-ag101.h
-F:	configs/adp-ag101_defconfig
diff --git a/board/AndesTech/adp-ag101/Makefile b/board/AndesTech/adp-ag101/Makefile
deleted file mode 100644
index 4cc590ff29..0000000000
--- a/board/AndesTech/adp-ag101/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# Copyright (C) 2011 Andes Technology Corporation
-# Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com>
-# Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= adp-ag101.o
diff --git a/board/AndesTech/adp-ag101/README b/board/AndesTech/adp-ag101/README
deleted file mode 100644
index 46fc637742..0000000000
--- a/board/AndesTech/adp-ag101/README
+++ /dev/null
@@ -1,74 +0,0 @@
-Andes Technology SoC AG101
-==========================
-
-AG101 is the first SoC produced by Andes Technology using N1213 CPU core.
-AG101 has integrated both AHB and APB bus and many periphals for application
-and product development.
-
-ADP-AG101
-=========
-
-ADP-AG101 is the SoC with AG101 hardcore CPU.
-
-Please check http://www.andestech.com/p2-4.htm for detail of this SoC.
-
-Configurations
-==============
-
-CONFIG_MEM_REMAP:
-	Doing memory remap is essential for preparing some non-OS or RTOS
-	applications.
-
-	This is also a must on ADP-AG101 board.
-	(While other boards may not have this problem).
-
-	The reason is because the ROM/FLASH circuit on PCB board.
-	AG101-A0 board has 2 jumpers MA17 and SW5 to configure which
-	ROM/FLASH is used to boot.
-
-	When SW5 = "0101", MA17 = LO, the ROM is connected to BANK0,
-	and the FLASH is connected to BANK1.
-	When SW5 = "1010", MA17 = HI, the ROM is disabled (still at BANK0),
-	and the FLASH is connected to BANK0.
-	It will occur problem when doing flash probing if the flash is at
-	BANK0 (0x00000000) while memory remapping was skipped.
-
-	Other board like ADP-AG101P may not enable this since there is only
-	a FLASH connected to bank0.
-
-CONFIG_SKIP_LOWLEVEL_INIT:
-	If you want to boot this system from FLASH and bypass e-bios (the
-	other boot loader on ROM). You should undefine CONFIG_SKIP_LOWLEVEL_INIT
-	in "include/configs/adp-ag101.h".
-
-Build and boot steps
-====================
-
-build:
-1. Prepare the toolchains and make sure the $PATH to toolchains is correct.
-2. Use `make adp-ag101` in u-boot root to build the image.
-
-burn u-boot to flash:
-1. Make sure the MA17 (J16) is Lo.
-2. Make sure the dip switch SW5 is set to "0101".
-3. Power On. Press button "S1", then press button "SW1", then you will found the
-   debug LED show 67 means the system successfully booted into e-bios.
-   Now you can control the e-bios boot loader from your console.
-4. Under "Command>>" prompt, enter "97" (CopyImageFromCard)
-5. Under "Type Dir Name of [CF/SD] =>" promtp, enter "c".
-6. Under "Enter Filename =>" prompt, enter the file name of u-boot image you
-   just build. It is usually "u-boot.bin".
-7. Under "Enter Dest. Address =>" prompt, enter the memory address where you
-   want to put the binary from SD card to RAM.
-   Address "0x500000" is our suggestion.
-8. Under "Command>>" prompt again, enter "55" (CLI) to use interactive command
-   environment.
-9. Under "CLI>" prompt, enter "burn 0x500000 0x80400000 0x30000" to burn the
-   binary from RAM to FLASH.
-10. Under "CLI>" prompt, enter "exit" to finish the burn process.
-
-boot u-boot from flash:
-1. Make sure the MA17 (J16) is Hi).
-2. Make sure the dip switch SW5 is set to "1010".
-3. Power On. Press button "S1", then you will see the debug LED count to 20.
-4. Now you can use u-boot on ADP-AG101 board.
diff --git a/board/AndesTech/adp-ag101/adp-ag101.c b/board/AndesTech/adp-ag101/adp-ag101.c
deleted file mode 100644
index 9884a5b52d..0000000000
--- a/board/AndesTech/adp-ag101/adp-ag101.c
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * Copyright (C) 2011 Andes Technology Corporation
- * Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com>
- * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-
-#include <faraday/ftsdc010.h>
-#include <faraday/ftsmc020.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscellaneous platform dependent initializations
- */
-
-int board_init(void)
-{
-	/*
-	 * refer to BOOT_PARAMETER_PA_BASE within
-	 * "linux/arch/nds32/include/asm/misc_spec.h"
-	 */
-	gd->bd->bi_arch_number = MACH_TYPE_ADPAG101;
-	gd->bd->bi_boot_params = PHYS_SDRAM_0 + 0x400;
-
-	ftsmc020_init();	/* initialize Flash */
-	return 0;
-}
-
-int dram_init(void)
-{
-	unsigned long sdram_base = PHYS_SDRAM_0;
-	unsigned long expected_size = PHYS_SDRAM_0_SIZE + PHYS_SDRAM_1_SIZE;
-	unsigned long actual_size;
-
-	actual_size = get_ram_size((void *)sdram_base, expected_size);
-
-	gd->ram_size = actual_size;
-
-	if (expected_size != actual_size) {
-		printf("Warning: Only %lu of %lu MiB SDRAM is working\n",
-				actual_size >> 20, expected_size >> 20);
-	}
-
-	return 0;
-}
-
-void dram_init_banksize(void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_0;
-	gd->bd->bi_dram[0].size =  PHYS_SDRAM_0_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[1].size =  PHYS_SDRAM_1_SIZE;
-}
-
-int board_eth_init(bd_t *bd)
-{
-	return ftmac100_initialize(bd);
-}
-
-ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
-{
-	if (banknum == 0) {	/* non-CFI boot flash */
-		info->portwidth = FLASH_CFI_8BIT;
-		info->chipwidth = FLASH_CFI_BY8;
-		info->interface = FLASH_CFI_X8;
-		return 1;
-	} else {
-		return 0;
-	}
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	ftsdc010_mmc_init(0);
-	return 0;
-}
diff --git a/board/AndesTech/adp-ag102/Kconfig b/board/AndesTech/adp-ag102/Kconfig
deleted file mode 100644
index fc17be3989..0000000000
--- a/board/AndesTech/adp-ag102/Kconfig
+++ /dev/null
@@ -1,18 +0,0 @@
-if TARGET_ADP_AG102
-
-config SYS_CPU
-	default "n1213"
-
-config SYS_BOARD
-	default "adp-ag102"
-
-config SYS_VENDOR
-	default "AndesTech"
-
-config SYS_SOC
-	default "ag102"
-
-config SYS_CONFIG_NAME
-	default "adp-ag102"
-
-endif
diff --git a/board/AndesTech/adp-ag102/MAINTAINERS b/board/AndesTech/adp-ag102/MAINTAINERS
deleted file mode 100644
index 94b87c7f0e..0000000000
--- a/board/AndesTech/adp-ag102/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ADP-AG102 BOARD
-M:	Andes <uboot@andestech.com>
-S:	Maintained
-F:	board/AndesTech/adp-ag102/
-F:	include/configs/adp-ag102.h
-F:	configs/adp-ag102_defconfig
diff --git a/board/AndesTech/adp-ag102/Makefile b/board/AndesTech/adp-ag102/Makefile
deleted file mode 100644
index fc4bf88a5c..0000000000
--- a/board/AndesTech/adp-ag102/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright (C) 2011 Andes Technology Corporation
-# Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= adp-ag102.o
diff --git a/board/AndesTech/adp-ag102/adp-ag102.c b/board/AndesTech/adp-ag102/adp-ag102.c
deleted file mode 100644
index 3f879ab3ce..0000000000
--- a/board/AndesTech/adp-ag102/adp-ag102.c
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
- * Copyright (C) 2011 Andes Technology Corporation
- * Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com>
- * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-
-#include <faraday/ftpci100.h>
-#include <faraday/ftsdc010.h>
-#ifdef CONFIG_FTSMC020
-#include <faraday/ftsmc020.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscellaneous platform dependent initializations
- */
-
-int board_init(void)
-{
-	/*
-	 * refer to BOOT_PARAMETER_PA_BASE within
-	 * "linux/arch/nds32/include/asm/misc_spec.h"
-	 */
-	gd->bd->bi_arch_number = MACH_TYPE_ADPAG102;
-	gd->bd->bi_boot_params = PHYS_SDRAM_0 + 0x400;
-
-#if !defined(CONFIG_SYS_NO_FLASH)
-	ftsmc020_init();	/* initialize Flash */
-#endif /* CONFIG_SYS_NO_FLASH */
-	return 0;
-}
-
-int dram_init(void)
-{
-	unsigned long sdram_base = PHYS_SDRAM_0;
-	unsigned long expected_size = PHYS_SDRAM_0_SIZE;
-	unsigned long actual_size;
-
-	actual_size = get_ram_size((void *)sdram_base, expected_size);
-
-	gd->ram_size = actual_size;
-
-	if (expected_size != actual_size) {
-		printf("Warning: Only %lu of %lu MiB SDRAM is working\n",
-				actual_size >> 20, expected_size >> 20);
-	}
-
-	return 0;
-}
-
-int board_eth_init(bd_t *bd)
-{
-	return ftgmac100_initialize(bd);
-}
-
-#if !defined(CONFIG_SYS_NO_FLASH)
-ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
-{
-	if (banknum == 0) {	/* non-CFI boot flash */
-		info->portwidth = FLASH_CFI_8BIT;
-		info->chipwidth = FLASH_CFI_BY8;
-		info->interface = FLASH_CFI_X8;
-		return 1;
-	} else {
-		return 0;
-	}
-}
-#endif /* CONFIG_SYS_NO_FLASH */
-
-#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
-void pci_init_board(void)
-{
-	/* should be pci_ftpci100_init() */
-	pci_ftpci_init();
-}
-#endif
-
-#ifdef CONFIG_GENERIC_MMC
-int board_mmc_init(bd_t *bis)
-{
-	ftsdc010_mmc_init(0);
-	return 0;
-}
-#endif