summaryrefslogtreecommitdiff
path: root/board/avionic-design/common/tamonten-ng.c
diff options
context:
space:
mode:
authorAlban Bedel <alban.bedel@avionic-design.de>2013-11-14 10:58:30 +0100
committerTom Warren <twarren@nvidia.com>2013-12-18 10:19:49 -0700
commit8f38038193752d3719f39ccd562f7ffdf83989d5 (patch)
tree80935a3ec3d34c6cc308f513336d021b8aef4b8c /board/avionic-design/common/tamonten-ng.c
parentac2ff538cde458a100da71974bdca8c2142e9e19 (diff)
ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board
Add support for the new Tamonten™ NG platform from Avionic Design. Currently only I2C, MMC, USB and ethernet have been tested. Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Diffstat (limited to 'board/avionic-design/common/tamonten-ng.c')
-rw-r--r--board/avionic-design/common/tamonten-ng.c85
1 files changed, 85 insertions, 0 deletions
diff --git a/board/avionic-design/common/tamonten-ng.c b/board/avionic-design/common/tamonten-ng.c
new file mode 100644
index 0000000000..9d395c676e
--- /dev/null
+++ b/board/avionic-design/common/tamonten-ng.c
@@ -0,0 +1,85 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/gp_padctrl.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+#include "pinmux-config-tamonten-ng.h"
+#include <i2c.h>
+
+#define PMU_I2C_ADDRESS 0x2D
+
+#define PMU_REG_LDO5 0x32
+
+#define PMU_REG_LDO_HIGH_POWER 1
+
+/* Voltage selection for the LDOs with 100mV resolution */
+#define PMU_REG_LDO_SEL_100(mV) ((((mV - 1000) / 100) + 2) << 2)
+
+#define PMU_REG_LDO_100(st, mV) (PMU_REG_LDO_##st | PMU_REG_LDO_SEL_100(mV))
+
+#define PMU_LDO5(st, mV) PMU_REG_LDO_100(st, mV)
+
+void pinmux_init(void)
+{
+ pinmux_config_table(tamonten_ng_pinmux_common,
+ ARRAY_SIZE(tamonten_ng_pinmux_common));
+ pinmux_config_table(unused_pins_lowpower,
+ ARRAY_SIZE(unused_pins_lowpower));
+
+ /* Initialize any non-default pad configs (APB_MISC_GP regs) */
+ padgrp_config_table(tamonten_ng_padctrl,
+ ARRAY_SIZE(tamonten_ng_padctrl));
+}
+
+void gpio_early_init(void)
+{
+ /* Turn on the alive signal */
+ gpio_request(GPIO_PV2, "ALIVE");
+ gpio_direction_output(GPIO_PV2, 1);
+
+ /* Remove the reset on the external periph */
+ gpio_request(GPIO_PI4, "nRST_PERIPH");
+ gpio_direction_output(GPIO_PI4, 1);
+}
+
+void pmu_write(uchar reg, uchar data)
+{
+ i2c_set_bus_num(4); /* PMU is on bus 4 */
+ i2c_write(PMU_I2C_ADDRESS, reg, 1, &data, 1);
+}
+
+/*
+ * Do I2C/PMU writes to bring up SD card bus power
+ *
+ */
+void board_sdmmc_voltage_init(void)
+{
+ /* Enable LDO5 with 3.3v for SDMMC3 */
+ pmu_write(PMU_REG_LDO5, PMU_LDO5(HIGH_POWER, 3300));
+
+ /* Switch the power on */
+ gpio_request(GPIO_PJ2, "EN_3V3_EMMC");
+ gpio_direction_output(GPIO_PJ2, 1);
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the MMC muxes, power rails, etc.
+ */
+void pin_mux_mmc(void)
+{
+ /*
+ * NOTE: We don't do mmc-specific pin muxes here.
+ * They were done globally in pinmux_init().
+ */
+
+ /* Bring up the SDIO1 power rail */
+ board_sdmmc_voltage_init();
+}