[Blackfin][PATCH] Add BF537 stamp board support

1 files changed, 515 insertions, 0 deletions

diff --git a/board/bf537-stamp/stm_m25p64.c b/board/bf537-stamp/stm_m25p64.c
new file mode 100644
index 0000000000..7077e85f41
--- /dev/null
+++ b/board/bf537-stamp/stm_m25p64.c
@@ -0,0 +1,515 @@
+/****************************************************************************
+ *  SPI flash driver for M25P64
+ ****************************************************************************/
+#include <common.h>
+#include <linux/ctype.h>
+#include <asm/io.h>
+
+#if defined(CONFIG_SPI)
+
+/* Application definitions */
+
+#define	NUM_SECTORS 	128	/* number of sectors */
+#define SECTOR_SIZE	0x10000
+#define NOP_NUM		1000
+
+#define COMMON_SPI_SETTINGS (SPE|MSTR|CPHA|CPOL) /* Settings to the SPI_CTL */
+#define TIMOD01 (0x01)	/* stes the SPI to work with core instructions */
+
+/* Flash commands */
+#define	SPI_WREN	(0x06)	/*Set Write Enable Latch */
+#define	SPI_WRDI	(0x04)	/*Reset Write Enable Latch */
+#define	SPI_RDSR	(0x05)	/*Read Status Register */
+#define	SPI_WRSR	(0x01)	/*Write Status Register */
+#define	SPI_READ	(0x03)	/*Read data from memory */
+#define	SPI_FAST_READ	(0x0B)	/*Read data from memory */
+#define	SPI_PP		(0x02)	/*Program Data into memory */
+#define	SPI_SE		(0xD8)	/*Erase one sector in memory */
+#define	SPI_BE		(0xC7)	/*Erase all memory */
+#define	WIP		(0x1)	/*Check the write in progress bit of the SPI status register */
+#define	WEL		(0x2)	/*Check the write enable bit of the SPI status register */
+
+#define	TIMEOUT		350000000
+
+typedef enum {
+	NO_ERR,
+	POLL_TIMEOUT,
+	INVALID_SECTOR,
+	INVALID_BLOCK,
+} ERROR_CODE;
+
+void spi_init_f(void);
+void spi_init_r(void);
+ssize_t spi_read(uchar *, int, uchar *, int);
+ssize_t spi_write(uchar *, int, uchar *, int);
+
+char ReadStatusRegister(void);
+void Wait_For_SPIF(void);
+void SetupSPI(const int spi_setting);
+void SPI_OFF(void);
+void SendSingleCommand(const int iCommand);
+
+ERROR_CODE GetSectorNumber(unsigned long ulOffset, int *pnSector);
+ERROR_CODE EraseBlock(int nBlock);
+ERROR_CODE ReadData(unsigned long ulStart, long lCount, int *pnData);
+ERROR_CODE WriteData(unsigned long ulStart, long lCount, int *pnData);
+ERROR_CODE Wait_For_Status(char Statusbit);
+ERROR_CODE Wait_For_WEL(void);
+
+/*
+ * Function:    spi_init_f
+ * Description: Init SPI-Controller (ROM part)
+ * return:      ---
+ */
+void spi_init_f(void)
+{
+}
+
+/*
+ * Function:    spi_init_r
+ * Description: Init SPI-Controller (RAM part) -
+ *		 The malloc engine is ready and we can move our buffers to
+ *		 normal RAM
+ *  return:      ---
+ */
+void spi_init_r(void)
+{
+	return;
+}
+
+/*
+ * Function:    spi_write
+ */
+ssize_t spi_write(uchar * addr, int alen, uchar * buffer, int len)
+{
+	unsigned long offset;
+	int start_block, end_block;
+	int start_byte, end_byte;
+	ERROR_CODE result = NO_ERR;
+	uchar temp[SECTOR_SIZE];
+	int i, num;
+
+	offset = addr[0] << 16 | addr[1] << 8 | addr[2];
+	/* Get the start block number */
+	result = GetSectorNumber(offset, &start_block);
+	if (result == INVALID_SECTOR) {
+		printf("Invalid sector! ");
+		return 0;
+	}
+	/* Get the end block number */
+	result = GetSectorNumber(offset + len - 1, &end_block);
+	if (result == INVALID_SECTOR) {
+		printf("Invalid sector! ");
+		return 0;
+	}
+
+	for (num = start_block; num <= end_block; num++) {
+		ReadData(num * SECTOR_SIZE, SECTOR_SIZE, (int *)temp);
+		start_byte = num * SECTOR_SIZE;
+		end_byte = (num + 1) * SECTOR_SIZE - 1;
+		if (start_byte < offset)
+			start_byte = offset;
+		if (end_byte > (offset + len))
+			end_byte = (offset + len - 1);
+		for (i = start_byte; i <= end_byte; i++)
+			temp[i - num * SECTOR_SIZE] = buffer[i - offset];
+		EraseBlock(num);
+		result = WriteData(num * SECTOR_SIZE, SECTOR_SIZE, (int *)temp);
+		if (result != NO_ERR)
+			return 0;
+		printf(".");
+	}
+	return len;
+}
+
+/*
+ * Function: spi_read
+ */
+ssize_t spi_read(uchar * addr, int alen, uchar * buffer, int len)
+{
+	unsigned long offset;
+	offset = addr[0] << 16 | addr[1] << 8 | addr[2];
+	ReadData(offset, len, (int *)buffer);
+	return len;
+}
+
+void SendSingleCommand(const int iCommand)
+{
+	unsigned short dummy;
+
+	/* turns on the SPI in single write mode */
+	SetupSPI((COMMON_SPI_SETTINGS | TIMOD01));
+
+	/* sends the actual command to the SPI TX register */
+	*pSPI_TDBR = iCommand;
+	sync();
+
+	/* The SPI status register will be polled to check the SPIF bit */
+	Wait_For_SPIF();
+
+	dummy = *pSPI_RDBR;
+
+	/* The SPI will be turned off */
+	SPI_OFF();
+
+}
+
+void SetupSPI(const int spi_setting)
+{
+
+	if (icache_status() || dcache_status())
+		udelay(CONFIG_CCLK_HZ / 50000000);
+	/*sets up the PF10 to be the slave select of the SPI */
+	*pPORTF_FER |= (PF10 | PF11 | PF12 | PF13);
+	*pSPI_FLG = 0xFF02;
+	*pSPI_BAUD = CONFIG_SPI_BAUD;
+	*pSPI_CTL = spi_setting;
+	sync();
+
+	*pSPI_FLG = 0xFD02;
+	sync();
+}
+
+void SPI_OFF(void)
+{
+
+	*pSPI_CTL = 0x0400;	/* disable SPI */
+	*pSPI_FLG = 0;
+	*pSPI_BAUD = 0;
+	sync();
+	udelay(CONFIG_CCLK_HZ / 50000000);
+
+}
+
+void Wait_For_SPIF(void)
+{
+	unsigned short dummyread;
+	while ((*pSPI_STAT & TXS)) ;
+	while (!(*pSPI_STAT & SPIF)) ;
+	while (!(*pSPI_STAT & RXS)) ;
+	/* Read dummy to empty the receive register */
+	dummyread = *pSPI_RDBR;
+}
+
+ERROR_CODE Wait_For_WEL(void)
+{
+	int i;
+	char status_register = 0;
+	ERROR_CODE ErrorCode = NO_ERR;
+
+	for (i = 0; i < TIMEOUT; i++) {
+		status_register = ReadStatusRegister();
+		if ((status_register & WEL)) {
+			ErrorCode = NO_ERR;
+			break;
+		}
+		ErrorCode = POLL_TIMEOUT;	/* Time out error */
+	};
+
+	return ErrorCode;
+}
+
+ERROR_CODE Wait_For_Status(char Statusbit)
+{
+	int i;
+	char status_register = 0xFF;
+	ERROR_CODE ErrorCode = NO_ERR;
+
+	for (i = 0; i < TIMEOUT; i++) {
+		status_register = ReadStatusRegister();
+		if (!(status_register & Statusbit)) {
+			ErrorCode = NO_ERR;
+			break;
+		}
+		ErrorCode = POLL_TIMEOUT;	/* Time out error */
+	};
+
+	return ErrorCode;
+}
+
+char ReadStatusRegister(void)
+{
+	char status_register = 0;
+
+	SetupSPI((COMMON_SPI_SETTINGS | TIMOD01));	/* Turn on the SPI */
+
+	*pSPI_TDBR = SPI_RDSR;	/* send instruction to read status register */
+	sync();
+	Wait_For_SPIF();	/*wait until the instruction has been sent */
+	*pSPI_TDBR = 0;		/*send dummy to receive the status register */
+	sync();
+	Wait_For_SPIF();	/*wait until the data has been sent */
+	status_register = *pSPI_RDBR;	/*read the status register */
+
+	SPI_OFF();		/* Turn off the SPI */
+
+	return status_register;
+}
+
+ERROR_CODE GetSectorNumber(unsigned long ulOffset, int *pnSector)
+{
+	int nSector = 0;
+	ERROR_CODE ErrorCode = NO_ERR;
+
+	if (ulOffset > (NUM_SECTORS * 0x10000 - 1)) {
+		ErrorCode = INVALID_SECTOR;
+		return ErrorCode;
+	}
+
+	nSector = (int)ulOffset / 0x10000;
+	*pnSector = nSector;
+
+	return ErrorCode;
+}
+
+ERROR_CODE EraseBlock(int nBlock)
+{
+	unsigned long ulSectorOff = 0x0, ShiftValue;
+	ERROR_CODE ErrorCode = NO_ERR;
+
+	/* if the block is invalid just return */
+	if ((nBlock < 0) || (nBlock > NUM_SECTORS)) {
+		ErrorCode = INVALID_BLOCK;
+		return ErrorCode;
+	}
+	/* figure out the offset of the block in flash */
+	if ((nBlock >= 0) && (nBlock < NUM_SECTORS)) {
+		ulSectorOff = (nBlock * SECTOR_SIZE);
+
+	} else {
+		ErrorCode = INVALID_BLOCK;
+		return ErrorCode;
+	}
+
+	/* A write enable instruction must previously have been executed */
+	SendSingleCommand(SPI_WREN);
+
+	/* The status register will be polled to check the write enable latch "WREN" */
+	ErrorCode = Wait_For_WEL();
+
+	if (POLL_TIMEOUT == ErrorCode) {
+		printf("SPI Erase block error\n");
+		return ErrorCode;
+	} else
+
+	/* Turn on the SPI to send single commands */
+	SetupSPI((COMMON_SPI_SETTINGS | TIMOD01));
+
+	/*
+	 * Send the erase block command to the flash followed by the 24 address
+	 * to point to the start of a sector
+	 */
+	*pSPI_TDBR = SPI_SE;
+	sync();
+	Wait_For_SPIF();
+	/* Send the highest byte of the 24 bit address at first */
+	ShiftValue = (ulSectorOff >> 16);
+	*pSPI_TDBR = ShiftValue;
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+	/* Send the middle byte of the 24 bit address  at second */
+	ShiftValue = (ulSectorOff >> 8);
+	*pSPI_TDBR = ShiftValue;
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+	/* Send the lowest byte of the 24 bit address finally */
+	*pSPI_TDBR = ulSectorOff;
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+
+	/* Turns off the SPI */
+	SPI_OFF();
+
+	/* Poll the status register to check the Write in Progress bit */
+	/* Sector erase takes time */
+	ErrorCode = Wait_For_Status(WIP);
+
+	/* block erase should be complete */
+	return ErrorCode;
+}
+
+/*
+ * ERROR_CODE ReadData()
+ * Read a value from flash for verify purpose
+ * Inputs:	unsigned long ulStart - holds the SPI start address
+ *			int pnData - pointer to store value read from flash
+ *			long lCount - number of elements to read
+ */
+ERROR_CODE ReadData(unsigned long ulStart, long lCount, int *pnData)
+{
+	unsigned long ShiftValue;
+	char *cnData;
+	int i;
+
+	/* Pointer cast to be able to increment byte wise */
+
+	cnData = (char *)pnData;
+	/* Start SPI interface */
+	SetupSPI((COMMON_SPI_SETTINGS | TIMOD01));
+
+#ifdef CONFIG_SPI_FLASH_FAST_READ
+	/* Send the read command to SPI device */
+	*pSPI_TDBR = SPI_FAST_READ;
+#else
+	/* Send the read command to SPI device */
+	*pSPI_TDBR = SPI_READ;
+#endif
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+	/* Send the highest byte of the 24 bit address at first */
+	ShiftValue = (ulStart >> 16);
+	/* Send the byte to the SPI device */
+	*pSPI_TDBR = ShiftValue;
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+	/* Send the middle byte of the 24 bit address  at second */
+	ShiftValue = (ulStart >> 8);
+	/* Send the byte to the SPI device */
+	*pSPI_TDBR = ShiftValue;
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+	/* Send the lowest byte of the 24 bit address finally */
+	*pSPI_TDBR = ulStart;
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+
+#ifdef CONFIG_SPI_FLASH_FAST_READ
+	/* Send dummy for FAST_READ */
+	*pSPI_TDBR = 0;
+	sync();
+	/* Wait until the instruction has been sent */
+	Wait_For_SPIF();
+#endif
+
+	/* After the SPI device address has been placed on the MOSI pin the data can be */
+	/* received on the MISO pin. */
+	for (i = 0; i < lCount; i++) {
+		*pSPI_TDBR = 0;
+		sync();
+		while (!(*pSPI_STAT & RXS)) ;
+		*cnData++ = *pSPI_RDBR;
+
+		if ((i >= SECTOR_SIZE) && (i % SECTOR_SIZE == 0))
+			printf(".");
+	}
+
+	/* Turn off the SPI */
+	SPI_OFF();
+
+	return NO_ERR;
+}
+
+ERROR_CODE WriteFlash(unsigned long ulStartAddr, long lTransferCount,
+		      int *iDataSource, long *lWriteCount)
+{
+
+	unsigned long ulWAddr;
+	long lWTransferCount = 0;
+	int i;
+	char iData;
+	char *temp = (char *)iDataSource;
+	ERROR_CODE ErrorCode = NO_ERR;
+
+	/* First, a Write Enable Command must be sent to the SPI. */
+	SendSingleCommand(SPI_WREN);
+
+	/*
+	 * Second, the SPI Status Register will be tested whether the
+	 * Write Enable Bit has been set
+	 */
+	ErrorCode = Wait_For_WEL();
+	if (POLL_TIMEOUT == ErrorCode) {
+		printf("SPI Write Time Out\n");
+		return ErrorCode;
+	} else
+		/* Third, the 24 bit address will be shifted out
+		 * the SPI MOSI bytewise.
+		 * Turns the SPI on
+		 */
+		SetupSPI((COMMON_SPI_SETTINGS | TIMOD01));
+	*pSPI_TDBR = SPI_PP;
+	sync();
+	/*wait until the instruction has been sent */
+	Wait_For_SPIF();
+	ulWAddr = (ulStartAddr >> 16);
+	*pSPI_TDBR = ulWAddr;
+	sync();
+	/*wait until the instruction has been sent */
+	Wait_For_SPIF();
+	ulWAddr = (ulStartAddr >> 8);
+	*pSPI_TDBR = ulWAddr;
+	sync();
+	/*wait until the instruction has been sent */
+	Wait_For_SPIF();
+	ulWAddr = ulStartAddr;
+	*pSPI_TDBR = ulWAddr;
+	sync();
+	/*wait until the instruction has been sent */
+	Wait_For_SPIF();
+	/*
+	 * Fourth, maximum number of 256 bytes will be taken from the Buffer
+	 * and sent to the SPI device.
+	 */
+	for (i = 0; (i < lTransferCount) && (i < 256); i++, lWTransferCount++) {
+		iData = *temp;
+		*pSPI_TDBR = iData;
+		sync();
+		/*wait until the instruction has been sent */
+		Wait_For_SPIF();
+		temp++;
+	}
+
+	/* Turns the SPI off */
+	SPI_OFF();
+
+	/*
+	 * Sixth, the SPI Write in Progress Bit must be toggled to ensure the
+	 * programming is done before start of next transfer
+	 */
+	ErrorCode = Wait_For_Status(WIP);
+
+	if (POLL_TIMEOUT == ErrorCode) {
+		printf("SPI Program Time out!\n");
+		return ErrorCode;
+	} else
+
+		*lWriteCount = lWTransferCount;
+
+	return ErrorCode;
+}
+
+ERROR_CODE WriteData(unsigned long ulStart, long lCount, int *pnData)
+{
+
+	unsigned long ulWStart = ulStart;
+	long lWCount = lCount, lWriteCount;
+	long *pnWriteCount = &lWriteCount;
+
+	ERROR_CODE ErrorCode = NO_ERR;
+
+	while (lWCount != 0) {
+		ErrorCode = WriteFlash(ulWStart, lWCount, pnData, pnWriteCount);
+
+		/*
+		 * After each function call of WriteFlash the counter
+		 * must be adjusted
+		 */
+		lWCount -= *pnWriteCount;
+
+		/* Also, both address pointers must be recalculated. */
+		ulWStart += *pnWriteCount;
+		pnData += *pnWriteCount / 4;
+	}
+
+	/* return the appropriate error code */
+	return ErrorCode;
+}
+
+#endif				/* CONFIG_SPI */