engicam: icorem6: Add DM_GPIO, DM_MMC support

Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

1 files changed, 72 insertions, 70 deletions

diff --git a/board/engicam/icorem6/icorem6.c b/board/engicam/icorem6/icorem6.c
index a23cb7e12b..a370c8bf8d 100644
--- a/board/engicam/icorem6/icorem6.c
+++ b/board/engicam/icorem6/icorem6.c
@@ -7,8 +7,6 @@
  */
 
 #include <common.h>
-#include <fsl_esdhc.h>
-#include <mmc.h>
 #include <miiphy.h>
 #include <netdev.h>
 
@@ -29,10 +27,6 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
 	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
 
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
-	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |               \
-	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
 #define ENET_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |		\
 	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
@@ -55,70 +49,6 @@ static iomux_v3_cfg_t const enet_pads[] = {
 	IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 };
 
-static iomux_v3_cfg_t const usdhc1_pads[] = {
-	IOMUX_PADS(PAD_SD1_CLK__SD1_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-	IOMUX_PADS(PAD_SD1_CMD__SD1_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-	IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-	IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-	IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-	IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-	IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),/* CD */
-};
-
-#ifdef CONFIG_FSL_ESDHC
-#define USDHC1_CD_GPIO	IMX_GPIO_NR(1, 1)
-
-struct fsl_esdhc_cfg usdhc_cfg[1] = {
-	{USDHC1_BASE_ADDR, 0, 4},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-	int ret = 0;
-
-	switch (cfg->esdhc_base) {
-	case USDHC1_BASE_ADDR:
-		ret = !gpio_get_value(USDHC1_CD_GPIO);
-		break;
-	}
-
-	return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	int i, ret;
-
-	/*
-	* According to the board_mmc_init() the following map is done:
-	* (U-boot device node)    (Physical Port)
-	* mmc0				USDHC1
-	*/
-	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
-		switch (i) {
-		case 0:
-			SETUP_IOMUX_PADS(usdhc1_pads);
-			gpio_direction_input(USDHC1_CD_GPIO);
-			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-			break;
-		default:
-			printf("Warning - USDHC%d controller not supporting\n",
-			       i + 1);
-			return 0;
-		}
-
-		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
-		if (ret) {
-			printf("Warning: failed to initialize mmc dev %d\n", i);
-			return ret;
-		}
-	}
-
-	return 0;
-}
-#endif
-
 #ifdef CONFIG_FEC_MXC
 #define ENET_PHY_RST		IMX_GPIO_NR(7, 12)
 static int setup_fec(void)
@@ -200,6 +130,78 @@ int dram_init(void)
 #include <asm/arch/crm_regs.h>
 #include <asm/arch/mx6-ddr.h>
 
+/* MMC board initialization is needed till adding DM support in SPL */
+#if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC)
+#include <mmc.h>
+#include <fsl_esdhc.h>
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |               \
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	IOMUX_PADS(PAD_SD1_CLK__SD1_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD1_CMD__SD1_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),/* CD */
+};
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(1, 1)
+
+struct fsl_esdhc_cfg usdhc_cfg[1] = {
+	{USDHC1_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+
+	/*
+	* According to the board_mmc_init() the following map is done:
+	* (U-boot device node)    (Physical Port)
+	* mmc0				USDHC1
+	*/
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			SETUP_IOMUX_PADS(usdhc1_pads);
+			gpio_direction_input(USDHC1_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		default:
+			printf("Warning - USDHC%d controller not supporting\n",
+			       i + 1);
+			return 0;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+#endif
+
 /*
  * Driving strength:
  *   0x30 == 40 Ohm