rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

2 files changed, 23 insertions, 23 deletions

diff --git a/board/esd/plu405/flash.c b/board/esd/plu405/flash.c
index 89af1190a8..274ada9fe5 100644
--- a/board/esd/plu405/flash.c
+++ b/board/esd/plu405/flash.c
@@ -48,7 +48,7 @@ unsigned long flash_init (void)
 	int size_val = 0;
 
 	/* Init: no FLASHes known */
-	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+	for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
 		flash_info[i].flash_id = FLASH_UNKNOWN;
 	}
 
@@ -91,7 +91,7 @@ unsigned long flash_init (void)
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
-			    -CFG_MONITOR_LEN,
+			    -CONFIG_SYS_MONITOR_LEN,
 			    0xffffffff,
 			    &flash_info[0]);
 
diff --git a/board/esd/plu405/plu405.c b/board/esd/plu405/plu405.c
index 3db9c0ad10..61186a8d7c 100644
--- a/board/esd/plu405/plu405.c
+++ b/board/esd/plu405/plu405.c
@@ -113,8 +113,8 @@ int misc_init_r (void)
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
 	gd->bd->bi_flashoffset = 0;
 
-	dst = malloc(CFG_FPGA_MAX_SIZE);
-	if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
+	dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
+	if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
 		printf ("GUNZIP ERROR - must RESET board to recover\n");
 		do_reset (NULL, 0, 0, NULL);
 	}
@@ -179,23 +179,23 @@ int misc_init_r (void)
 	/*
 	 * Reset external DUARTs
 	 */
-	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_DUART_RST);
+	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CONFIG_SYS_DUART_RST);
 	udelay(10);
-	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~CFG_DUART_RST);
+	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~CONFIG_SYS_DUART_RST);
 	udelay(1000);
 
 	/*
 	 * Set NAND-FLASH GPIO signals to default
 	 */
 	out_be32((void*)GPIO0_OR,
-		 in_be32((void*)GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_NAND_CE);
+		 in_be32((void*)GPIO0_OR) & ~(CONFIG_SYS_NAND_CLE | CONFIG_SYS_NAND_ALE));
+	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CONFIG_SYS_NAND_CE);
 
 	/*
 	 * Setup EEPROM write protection
 	 */
-	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_EEPROM_WP);
-	out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) | CFG_EEPROM_WP);
+	out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
+	out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) | CONFIG_SYS_EEPROM_WP);
 
 	/*
 	 * Enable interrupts in exar duart mcr[3]
@@ -230,15 +230,15 @@ int checkboard (void)
 void ide_set_reset(int on)
 {
 	volatile unsigned short *fpga_mode =
-		(unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL);
+		(unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL);
 
 	/*
 	 * Assert or deassert CompactFlash Reset Pin
 	 */
 	if (on) {		/* assert RESET */
-		*fpga_mode &= ~(CFG_FPGA_CTRL_CF_RESET);
+		*fpga_mode &= ~(CONFIG_SYS_FPGA_CTRL_CF_RESET);
 	} else {		/* release RESET */
-		*fpga_mode |= CFG_FPGA_CTRL_CF_RESET;
+		*fpga_mode |= CONFIG_SYS_FPGA_CTRL_CF_RESET;
 	}
 }
 #endif /* CONFIG_IDE_RESET */
@@ -254,7 +254,7 @@ void reset_phy(void)
 #endif
 }
 
-#if defined(CFG_EEPROM_WREN)
+#if defined(CONFIG_SYS_EEPROM_WREN)
 /* Input: <dev_addr>  I2C address of EEPROM device to enable.
  *         <state>     -1: deliver current state
  *	               0: disable write
@@ -265,26 +265,26 @@ void reset_phy(void)
  */
 int eeprom_write_enable (unsigned dev_addr, int state)
 {
-	if (CFG_I2C_EEPROM_ADDR != dev_addr) {
+	if (CONFIG_SYS_I2C_EEPROM_ADDR != dev_addr) {
 		return -1;
 	} else {
 		switch (state) {
 		case 1:
 			/* Enable write access, clear bit GPIO0. */
 			out_be32((void*)GPIO0_OR,
-				 in_be32((void*)GPIO0_OR) & ~CFG_EEPROM_WP);
+				 in_be32((void*)GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP);
 			state = 0;
 			break;
 		case 0:
 			/* Disable write access, set bit GPIO0. */
 			out_be32((void*)GPIO0_OR,
-				 in_be32((void*)GPIO0_OR) | CFG_EEPROM_WP);
+				 in_be32((void*)GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
 			state = 0;
 			break;
 		default:
 			/* Read current status back. */
 			state = (0 == (in_be32((void*)GPIO0_OR) &
-				       CFG_EEPROM_WP));
+				       CONFIG_SYS_EEPROM_WP));
 			break;
 		}
 	}
@@ -298,21 +298,21 @@ int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 	if (query) {
 		/* Query write access state. */
-		state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, -1);
+		state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, -1);
 		if (state < 0) {
 			puts ("Query of write access state failed.\n");
 		} else {
 			printf ("Write access for device 0x%0x is %sabled.\n",
-				CFG_I2C_EEPROM_ADDR, state ? "en" : "dis");
+				CONFIG_SYS_I2C_EEPROM_ADDR, state ? "en" : "dis");
 			state = 0;
 		}
 	} else {
 		if ('0' == argv[1][0]) {
 			/* Disable write access. */
-			state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 0);
+			state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 0);
 		} else {
 			/* Enable write access. */
-			state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 1);
+			state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 1);
 		}
 		if (state < 0) {
 			puts ("Setup of write access state failed.\n");
@@ -325,4 +325,4 @@ int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 U_BOOT_CMD(eepwren,	2,	0,	do_eep_wren,
 	   "eepwren - Enable / disable / query EEPROM write access\n",
 	   NULL);
-#endif /* #if defined(CFG_EEPROM_WREN) */
+#endif /* #if defined(CONFIG_SYS_EEPROM_WREN) */