arm: ls102xa: Add basic support for LS1021AQDS board

LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
 One DDR controller
 DUART1 is used as the console

For the detail board information, please refer to README.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

1 files changed, 159 insertions, 0 deletions

diff --git a/board/freescale/ls1021aqds/ddr.c b/board/freescale/ls1021aqds/ddr.c
new file mode 100644
index 0000000000..679c654fb5
--- /dev/null
+++ b/board/freescale/ls1021aqds/ddr.c
@@ -0,0 +1,159 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			   dimm_params_t *pdimm,
+			   unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 3) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	pbsp = udimms[0];
+
+	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				popts->cpo_override = pbsp->cpo_override;
+				popts->write_data_delay =
+					pbsp->write_data_delay;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found for %lu MT/s\n",
+		       ddr_freq);
+		printf("Trying to use the highest speed (%u) parameters\n",
+		       pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+	      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+
+	/* force DDR bus width to 32 bits */
+	popts->data_bus_width = 1;
+	popts->otf_burst_chop_en = 0;
+	popts->burst_length = DDR_BL8;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 1;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+	popts->cswl_override = DDR_CSWL_CS0;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 75 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+dimm_params_t ddr_raw_timing = {
+	.n_ranks = 1,
+	.rank_density = 1073741824u,
+	.capacity = 1073741824u,
+	.primary_sdram_width = 32,
+	.ec_sdram_width = 0,
+	.registered_dimm = 0,
+	.mirrored_dimm = 0,
+	.n_row_addr = 15,
+	.n_col_addr = 10,
+	.n_banks_per_sdram_device = 8,
+	.edc_config = 0,
+	.burst_lengths_bitmask = 0x0c,
+
+	.tckmin_x_ps = 1071,
+	.caslat_x = 0xfe << 4,	/* 5,6,7,8 */
+	.taa_ps = 13125,
+	.twr_ps = 15000,
+	.trcd_ps = 13125,
+	.trrd_ps = 7500,
+	.trp_ps = 13125,
+	.tras_ps = 37500,
+	.trc_ps = 50625,
+	.trfc_ps = 160000,
+	.twtr_ps = 7500,
+	.trtp_ps = 7500,
+	.refresh_rate_ps = 7800000,
+	.tfaw_ps = 37500,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+			    unsigned int controller_number,
+			    unsigned int dimm_number)
+{
+	static const char dimm_model[] = "Fixed DDR on board";
+
+	if (((controller_number == 0) && (dimm_number == 0)) ||
+	    ((controller_number == 1) && (dimm_number == 0))) {
+		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+	}
+
+	return 0;
+}
+#endif
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing DDR....using SPD\n");
+	dram_size = fsl_ddr_sdram();
+
+	return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}