doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 409 insertions, 0 deletions

diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README
new file mode 100644
index 0000000000..2bc6ce4bf3
--- /dev/null
+++ b/board/freescale/m54455evb/README
@@ -0,0 +1,409 @@
+Freescale MCF54455EVB ColdFire Development Board
+================================================
+
+TsiChung Liew(Tsi-Chung.Liew@freescale.com)
+Created 4/08/07
+===========================================
+
+
+Changed files:
+==============
+
+- board/freescale/m54455evb/m54455evb.c	Dram setup, IDE pre init, and PCI init
+- board/freescale/m54455evb/flash.c		Atmel and INTEL flash support
+- board/freescale/m54455evb/Makefile		Makefile
+- board/freescale/m54455evb/config.mk	config make
+- board/freescale/m54455evb/u-boot.lds	Linker description
+
+- common/cmd_bdinfo.c		Clock frequencies output
+- common/cmd_mii.c		mii support
+
+- arch/m68k/cpu/mcf5445x/cpu.c		cpu specific code
+- arch/m68k/cpu/mcf5445x/cpu_init.c	Flexbus ChipSelect, Mux pins setup, icache and RTC extra regs
+- arch/m68k/cpu/mcf5445x/interrupts.c	cpu specific interrupt support
+- arch/m68k/cpu/mcf5445x/speed.c		system, pci, flexbus, and cpu clock
+- arch/m68k/cpu/mcf5445x/Makefile		Makefile
+- arch/m68k/cpu/mcf5445x/config.mk	config make
+- arch/m68k/cpu/mcf5445x/start.S		start up assembly code
+
+- doc/README.m54455evb	This readme file
+
+- drivers/net/mcffec.c		ColdFire common FEC driver
+- drivers/serial/mcfuart.c	ColdFire common UART driver
+
+- include/asm-m68k/bitops.h		Bit operation function export
+- include/asm-m68k/byteorder.h		Byte order functions
+- include/asm-m68k/fec.h		FEC structure and definition
+- include/asm-m68k/fsl_i2c.h		I2C structure and definition
+- include/asm-m68k/global_data.h	Global data structure
+- include/asm-m68k/immap.h		ColdFire specific header file and driver macros
+- include/asm-m68k/immap_5445x.h	mcf5445x specific header file
+- include/asm-m68k/io.h			io functions
+- include/asm-m68k/m5445x.h		mcf5445x specific header file
+- include/asm-m68k/posix_types.h	Posix
+- include/asm-m68k/processor.h		header file
+- include/asm-m68k/ptrace.h		Exception structure
+- include/asm-m68k/rtc.h		Realtime clock header file
+- include/asm-m68k/string.h		String function export
+- include/asm-m68k/timer.h		Timer structure and definition
+- include/asm-m68k/types.h		Data types definition
+- include/asm-m68k/uart.h		Uart structure and definition
+- include/asm-m68k/u-boot.h		u-boot structure
+
+- include/configs/M54455EVB.h	Board specific configuration file
+
+- arch/m68k/lib/board.c			board init function
+- arch/m68k/lib/cache.c
+- arch/m68k/lib/interrupts			Coldfire common interrupt functions
+- arch/m68k/lib/m68k_linux.c
+- arch/m68k/lib/time.c			Timer functions (Dma timer and PIT)
+- arch/m68k/lib/traps.c			Exception init code
+
+- rtc/mcfrtc.c				Realtime clock Driver
+
+1 MCF5445x specific Options/Settings
+====================================
+1.1 pre-loader is no longer suppoer in thie coldfire family
+
+1.2 Configuration settings for M54455EVB Development Board
+CONFIG_MCF5445x		-- define for all MCF5445x CPUs
+CONFIG_M54455		-- define for all Freescale MCF54455 CPUs
+CONFIG_M54455EVB	-- define for M54455EVB board
+
+CONFIG_MCFUART		-- define to use common CF Uart driver
+CONFIG_SYS_UART_PORT		-- define UART port number, start with 0, 1 and 2
+CONFIG_BAUDRATE		-- define UART baudrate
+
+CONFIG_MCFRTC		-- define to use common CF RTC driver
+CONFIG_SYS_MCFRTC_BASE		-- provide base address for RTC in immap.h
+CONFIG_SYS_RTC_OSCILLATOR	-- define RTC clock frequency
+RTC_DEBUG		-- define to show RTC debug message
+CONFIG_CMD_DATE		-- enable to use date feature in u-boot
+
+CONFIG_MCFFEC		-- define to use common CF FEC driver
+CONFIG_MII		-- enable to use MII driver
+CONFIG_CF_DOMII		-- enable to use MII feature in cmd_mii.c
+CONFIG_SYS_DISCOVER_PHY	-- enable PHY discovery
+CONFIG_SYS_RX_ETH_BUFFER	-- Set FEC Receive buffer
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN--
+CONFIG_SYS_FEC0_PINMUX		-- Set FEC0 Pin configuration
+CONFIG_SYS_FEC1_PINMUX		-- Set FEC1 Pin configuration
+CONFIG_SYS_FEC0_MIIBASE	-- Set FEC0 MII base register
+CONFIG_SYS_FEC1_MIIBASE	-- Set FEC0 MII base register
+MCFFEC_TOUT_LOOP	-- set FEC timeout loop
+CONFIG_HAS_ETH1		-- define to enable second FEC in u-boot
+
+CONFIG_ISO_PARTITION	-- enable ISO read/write
+CONFIG_DOS_PARTITION	-- enable DOS read/write
+CONFIG_IDE_RESET	-- define ide_reset()
+CONFIG_IDE_PREINIT	-- define ide_preinit()
+CONFIG_ATAPI		-- define ATAPI support
+CONFIG_LBA48		-- define LBA48 (larger than 120GB) support
+CONFIG_SYS_IDE_MAXBUS		-- define max channel
+CONFIG_SYS_IDE_MAXDEVICE	-- define max devices per channel
+CONFIG_SYS_ATA_BASE_ADDR	-- define ATA base address
+CONFIG_SYS_ATA_IDE0_OFFSET	-- define ATA IDE0 offset
+CONFIG_SYS_ATA_DATA_OFFSET	-- define ATA data IO
+CONFIG_SYS_ATA_REG_OFFSET	-- define for normal register accesses
+CONFIG_SYS_ATA_ALT_OFFSET	-- define for alternate registers
+CONFIG_SYS_ATA_STRIDE		-- define for Interval between registers
+_IO_BASE		-- define for IO base address
+
+CONFIG_MCFTMR		-- define to use DMA timer
+CONFIG_MCFPIT		-- define to use PIT timer
+
+CONFIG_FSL_I2C		-- define to use FSL common I2C driver
+CONFIG_HARD_I2C		-- define for I2C hardware support
+CONFIG_SOFT_I2C		-- define for I2C bit-banged
+CONFIG_SYS_I2C_SPEED		-- define for I2C speed
+CONFIG_SYS_I2C_SLAVE		-- define for I2C slave address
+CONFIG_SYS_I2C_OFFSET		-- define for I2C base address offset
+CONFIG_SYS_IMMR		-- define for MBAR offset
+
+CONFIG_PCI              -- define for PCI support
+CONFIG_PCI_PNP          -- define for Plug n play support
+CONFIG_SYS_PCI_MEM_BUS		-- PCI memory logical offset
+CONFIG_SYS_PCI_MEM_PHYS	-- PCI memory physical offset
+CONFIG_SYS_PCI_MEM_SIZE	-- PCI memory size
+CONFIG_SYS_PCI_IO_BUS		-- PCI IO logical offset
+CONFIG_SYS_PCI_IO_PHYS		-- PCI IO physical offset
+CONFIG_SYS_PCI_IO_SIZE		-- PCI IO size
+CONFIG_SYS_PCI_CFG_BUS		-- PCI Configuration logical offset
+CONFIG_SYS_PCI_CFG_PHYS	-- PCI Configuration physical offset
+CONFIG_SYS_PCI_CFG_SIZE	-- PCI Configuration size
+
+CONFIG_EXTRA_CLOCK	-- Enable extra clock such as vco, flexbus, pci, etc
+
+CONFIG_SYS_MBAR		-- define MBAR offset
+
+CONFIG_SYS_ATMEL_BOOT		-- To determine the u-boot is booted from Atmel or Intel
+
+CONFIG_MONITOR_IS_IN_RAM -- Not support
+
+CONFIG_SYS_INIT_RAM_ADDR	-- defines the base address of the MCF54455 internal SRAM
+
+CONFIG_SYS_CSn_BASE	-- defines the Chip Select Base register
+CONFIG_SYS_CSn_MASK	-- defines the Chip Select Mask register
+CONFIG_SYS_CSn_CTRL	-- defines the Chip Select Control register
+
+CONFIG_SYS_ATMEL_BASE	-- defines the Atmel Flash base
+CONFIG_SYS_INTEL_BASE	-- defines the Intel Flash base
+
+CONFIG_SYS_SDRAM_BASE	-- defines the DRAM Base
+CONFIG_SYS_SDRAM_BASE1	-- defines the DRAM Base 1
+
+2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
+===========================================
+2.1. System memory map:
+	Flash:		0x00000000-0x3FFFFFFF (1024MB)
+	DDR:		0x40000000-0x7FFFFFFF (1024MB)
+	SRAM:		0x80000000-0x8FFFFFFF (256MB)
+	ATA:		0x90000000-0x9FFFFFFF (256MB)
+	PCI:		0xA0000000-0xBFFFFFFF (512MB)
+	FlexBus:	0xC0000000-0xDFFFFFFF (512MB)
+	IP:		0xF0000000-0xFFFFFFFF (256MB)
+
+2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+	linux kernel, you can customize it based on your system requirements:
+	Atmel boot:
+	Flash0:		0x00000000-0x0007FFFF (512KB)
+	Flash1:		0x04000000-0x05FFFFFF (32MB)
+	Intel boot:
+	Flash0:		0x00000000-0x01FFFFFF (32MB)
+	Flash1:		0x04000000-0x0407FFFF (512KB)
+
+	CPLD:		0x08000000-0x08FFFFFF (16MB)
+	FPGA:		0x09000000-0x09FFFFFF (16MB)
+	DDR:		0x40000000-0x4FFFFFFF (256MB)
+	SRAM:		0x80000000-0x80007FFF (32KB)
+	IP:		0xFC000000-0xFC0FFFFF (64KB)
+
+3. SWITCH SETTINGS
+==================
+3.1 SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL
+	SW1 Pin4: 0 - ULPI chip not in reset state or 1 - ULPI chip in reset state
+	SW1 Pin5: 0 - Full ATA Bus enabled, FEC Phy1 powered down
+			  1 - Upper 8 bits ATA data bus disabled, FEC PHY1 active
+	SW1 Pin6: 0 - FEC Phy0 active or 1 - FEC Phy0 powered down
+	SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL
+
+4. COMPILATION
+==============
+4.1	To create U-Boot the gcc-4.1-32 compiler set (ColdFire ELF version)
+from codesourcery.com was used. Download it from:
+http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
+
+4.2 Compilation
+   export CROSS_COMPILE=cross-compile-prefix
+   cd u-boot-1.x.x
+   make distclean
+   make M54455EVB_config, or		- default to atmel 33Mhz input clock
+   make M54455EVB_atmel_config, or	- default to atmel 33Mhz input clock
+   make M54455EVB_a33_config, or	- default to atmel 33Mhz input clock
+   make M54455EVB_a66_config, or	- default to atmel 66Mhz input clock
+   make M54455EVB_intel_config, or	- default to intel 33Mhz input clock
+   make M54455EVB_i33_config, or	- default to intel 33Mhz input clock
+   make M54455EVB_i66_config, or	- default to intel 66Mhz input clock
+   make
+
+5. SCREEN DUMP
+==============
+5.1 M54455EVB Development board
+    Boot from Atmel (NOTE: May not show exactly the same)
+
+U-Boot 1.2.0-g98c80b46-dirty (Jul 26 2007 - 12:44:08)
+
+CPU:   Freescale MCF54455 (Mask:48 Version:1)
+       CPU CLK 266 Mhz BUS CLK 133 Mhz FLB CLK 66 Mhz
+       PCI CLK 33 Mhz INP CLK 33 Mhz VCO CLK 533 Mhz
+Board: Freescale M54455 EVB
+I2C:   ready
+DRAM:  256 MB
+FLASH: 16.5 MB
+In:    serial
+Out:   serial
+Err:   serial
+Net:   FEC0, FEC1
+IDE:   Bus 0: not available
+-> print
+bootargs=root=/dev/ram rw
+bootdelay=1
+baudrate=115200
+ethaddr=00:e0:0c:bc:e5:60
+eth1addr=00:e0:0c:bc:e5:61
+hostname=M54455EVB
+netdev=eth0
+inpclk=33333333
+loadaddr=40010000
+load=tftp ${loadaddr) ${u-boot}
+upd=run load; run prog
+prog=prot off 0 2ffff;era 0 2ffff;cp.b ${loadaddr} 0 ${filesize};save
+ethact=FEC0
+mtdids=nor0=M54455EVB-1
+mtdparts=M54455EVB-1:16m(user)
+u-boot=u-boot54455.bin
+filesize=292b4
+fileaddr=40010000
+gatewayip=192.168.1.1
+netmask=255.255.255.0
+ipaddr=192.168.1.3
+serverip=192.168.1.2
+stdin=serial
+stdout=serial
+stderr=serial
+mem=261632k
+
+Environment size: 563/8188 bytes
+-> bdinfo
+memstart    = 0x40000000
+memsize     = 0x10000000
+flashstart  = 0x00000000
+flashsize   = 0x01080000
+flashoffset = 0x00000000
+sramstart   = 0x80000000
+sramsize    = 0x00008000
+mbar        = 0xFC000000
+busfreq     = 133.333 MHz
+pcifreq     = 33.333 MHz
+flbfreq     = 66.666 MHz
+inpfreq     = 33.333 MHz
+vcofreq     = 533.333 MHz
+ethaddr     = 00:E0:0C:BC:E5:60
+eth1addr    = 00:E0:0C:BC:E5:61
+ip_addr     = 192.168.1.3
+baudrate    = 115200 bps
+->
+-> help
+?       - alias for 'help'
+base    - print or set address offset
+bdinfo  - print Board Info structure
+boot    - boot default, i.e., run 'bootcmd'
+bootd   - boot default, i.e., run 'bootcmd'
+bootelf - Boot from an ELF image in memory
+bootm   - boot application image from memory
+bootp	- boot image via network using BootP/TFTP protocol
+bootvx  - Boot vxWorks from an ELF image
+cmp     - memory compare
+coninfo - print console devices and information
+cp      - memory copy
+crc32   - checksum calculation
+date    - get/set/reset date & time
+dcache  - enable or disable data cache
+diskboot- boot from IDE device
+echo    - echo args to console
+erase   - erase FLASH memory
+ext2load- load binary file from a Ext2 filesystem
+ext2ls  - list files in a directory (default /)
+fatinfo - print information about filesystem
+fatload - load binary file from a dos filesystem
+fatls   - list files in a directory (default /)
+flinfo  - print FLASH memory information
+fsinfo	- print information about filesystems
+fsload	- load binary file from a filesystem image
+go      - start application at address 'addr'
+help    - print online help
+i2c     - I2C sub-system
+icache  - enable or disable instruction cache
+ide     - IDE sub-system
+iminfo  - print header information for application image
+imls    - list all images found in flash
+itest	- return true/false on integer compare
+loadb   - load binary file over serial line (kermit mode)
+loads   - load S-Record file over serial line
+loady   - load binary file over serial line (ymodem mode)
+loop    - infinite loop on address range
+ls	- list files in a directory (default /)
+md      - memory display
+mii     - MII utility commands
+mm      - memory modify (auto-incrementing)
+mtest   - simple RAM test
+mw      - memory write (fill)
+nfs	- boot image via network using NFS protocol
+nm      - memory modify (constant address)
+pci     - list and access PCI Configuration Space
+ping	- send ICMP ECHO_REQUEST to network host
+printenv- print environment variables
+protect - enable or disable FLASH write protection
+rarpboot- boot image via network using RARP/TFTP protocol
+reset   - Perform RESET of the CPU
+run     - run commands in an environment variable
+saveenv - save environment variables to persistent storage
+setenv  - set environment variables
+sleep   - delay execution for some time
+source  - run script from memory
+tftpboot- boot image via network using TFTP protocol
+version - print monitor version
+->bootm 4000000
+
+## Booting image at 04000000 ...
+   Image Name:   Linux Kernel Image
+   Created:      2007-08-14  15:13:00 UTC
+   Image Type:   M68K Linux Kernel Image (uncompressed)
+   Data Size:    2301952 Bytes =  2.2 MB
+   Load Address: 40020000
+   Entry Point:  40020000
+   Verifying Checksum ... OK
+OK
+Linux version 2.6.20-gfe5136d6-dirty (mattw@kea) (gcc version 4.2.0 20070318 (pr
+erelease) (Sourcery G++ Lite 4.2-20)) #108 Mon Aug 13 13:00:13 MDT 2007
+starting up linux startmem 0xc0254000, endmem 0xcfffffff, size 253MB
+Built 1 zonelists.  Total pages: 32624
+Kernel command line: root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=ph
+ysmap-flash.0:5M(kernel)ro,-(jffs2)
+PID hash table entries: 1024 (order: 10, 4096 bytes)
+Console: colour dummy device 80x25
+Dentry cache hash table entries: 32768 (order: 4, 131072 bytes)
+Inode-cache hash table entries: 16384 (order: 3, 65536 bytes)
+Memory: 257496k/262136k available (1864k kernel code, 2440k data, 88k init)
+Mount-cache hash table entries: 1024
+NET: Registered protocol family 16
+SCSI subsystem initialized
+NET: Registered protocol family 2
+IP route cache hash table entries: 2048 (order: 0, 8192 bytes)
+TCP established hash table entries: 8192 (order: 2, 32768 bytes)
+TCP bind hash table entries: 4096 (order: 1, 16384 bytes)
+TCP: Hash tables configured (established 8192 bind 4096)
+TCP reno registered
+JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
+io scheduler noop registered
+io scheduler anticipatory registered
+io scheduler deadline registered
+io scheduler cfq registered (default)
+ColdFire internal UART serial driver version 1.00
+ttyS0 at 0xfc060000 (irq = 90) is a builtin ColdFire UART
+ttyS1 at 0xfc064000 (irq = 91) is a builtin ColdFire UART
+ttyS2 at 0xfc068000 (irq = 92) is a builtin ColdFire UART
+RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
+loop: loaded (max 8 devices)
+FEC ENET Version 0.2
+fec: PHY @ 0x0, ID 0x20005ca2 -- DP83849
+eth0: ethernet 00:08:ee:00:e4:19
+physmap platform flash device: 01000000 at 04000000
+physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
+ Intel/Sharp Extended Query Table at 0x0031
+Using buffer write method
+cfi_cmdset_0001: Erase suspend on write enabled
+2 cmdlinepart partitions found on MTD device physmap-flash.0
+Creating 2 MTD partitions on "physmap-flash.0":
+0x00000000-0x00500000 : "kernel"
+mtd: Giving out device 0 to kernel
+0x00500000-0x01000000 : "jffs2"
+mtd: Giving out device 1 to jffs2
+mice: PS/2 mouse device common for all mice
+i2c /dev entries driver
+TCP cubic registered
+NET: Registered protocol family 1
+NET: Registered protocol family 17
+NET: Registered protocol family 15
+VFS: Mounted root (jffs2 filesystem).
+Setting the hostname to freescale
+Mounting filesystems
+mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory
+Starting syslogd and klogd
+Setting up networking on loopback device:
+Setting up networking on eth0:
+eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX.
+Adding static route for default gateway to 172.27.255.254:
+Setting nameserver to 172.27.0.1 in /etc/resolv.conf:
+Starting inetd:
+/ #