85xx: Add P2020DS support

The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.

Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

1 files changed, 130 insertions, 0 deletions

diff --git a/board/freescale/p2020ds/ddr.c b/board/freescale/p2020ds/ddr.c
new file mode 100644
index 0000000000..b9c0cb2576
--- /dev/null
+++ b/board/freescale/p2020ds/ddr.c
@@ -0,0 +1,130 @@
+/*
+ * Copyright 2008-2009 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0)
+			i2c_address = SPD_EEPROM_ADDRESS1;
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+typedef struct {
+	u32 datarate_mhz_low;
+	u32 datarate_mhz_high;
+	u32 n_ranks;
+	u32 clk_adjust;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2T;
+} board_specific_parameters_t;
+
+/* ranges for parameters:
+ *  wr_data_delay = 0-6
+ *  clk adjust = 0-8
+ *  cpo 2-0x1E (30)
+ */
+
+
+/* XXX: these values need to be checked for all interleaving modes.  */
+/* XXX: No reliable dual-rank 800 MHz setting has been found.  It may
+ *      seem reliable, but errors will appear when memory intensive
+ *      program is run. */
+/* XXX: Single rank at 800 MHz is OK.  */
+const board_specific_parameters_t board_specific_parameters[][20] = {
+	{
+	/* 	memory controller 0 			*/
+	/*	  lo|  hi|  num|  clk| cpo|wrdata|2T	*/
+	/*	 mhz| mhz|ranks|adjst|    | delay|	*/
+		{  0, 333,    2,    6,   7,    3,  0},
+		{334, 400,    2,    6,   9,    3,  0},
+		{401, 549,    2,    6,  11,    3,  0},
+		{550, 680,    2,    1,  10,    5,  0},
+		{681, 850,    2,    1,  12,    5,  1},
+		{  0, 333,    1,    6,   7,    3,  0},
+		{334, 400,    1,    6,   9,    3,  0},
+		{401, 549,    1,    6,  11,    3,  0},
+		{550, 680,    1,    1,  10,    5,  0},
+		{681, 850,    1,    1,  12,    5,  0}
+	},
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const board_specific_parameters_t *pbsp =
+				&(board_specific_parameters[ctrl_num][0]);
+	u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+				sizeof(board_specific_parameters[0][0]);
+	u32 i;
+	ulong ddr_freq;
+
+	/* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+	 * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+	 * there are two dimms in the controller, set odt_rd_cfg to 3 and
+	 * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
+	 */
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i&1) {	/* odd CS */
+			popts->cs_local_opts[i].odt_rd_cfg = 0;
+			popts->cs_local_opts[i].odt_wr_cfg = 0;
+		} else {	/* even CS */
+			if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+				popts->cs_local_opts[i].odt_rd_cfg = 0;
+				popts->cs_local_opts[i].odt_wr_cfg = 4;
+			} else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+				popts->cs_local_opts[i].odt_rd_cfg = 3;
+				popts->cs_local_opts[i].odt_wr_cfg = 3;
+			}
+		}
+	}
+
+	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	for (i = 0; i < num_params; i++) {
+		if (ddr_freq >= pbsp->datarate_mhz_low &&
+		    ddr_freq <= pbsp->datarate_mhz_high &&
+		    pdimm->n_ranks == pbsp->n_ranks) {
+			popts->clk_adjust = pbsp->clk_adjust;
+			popts->cpo_override = pbsp->cpo;
+			popts->write_data_delay = pbsp->write_data_delay;
+			popts->twoT_en = pbsp->force_2T;
+		}
+		pbsp++;
+	}
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}