mx35: Clean up lowlevel_init

Clean up mx35 lowlevel_init:
 - Indent with tabs.
 - Fix comments.
 - Use defined values instead of literal constants.
 - Use defined macros instead of duplicating code.
 - Use macro parameters with default values instead of #define'd configs.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

2 files changed, 2 insertions, 142 deletions

diff --git a/board/freescale/mx35pdk/lowlevel_init.S b/board/freescale/mx35pdk/lowlevel_init.S
index 698c4cf0c5..75bb958619 100644
--- a/board/freescale/mx35pdk/lowlevel_init.S
+++ b/board/freescale/mx35pdk/lowlevel_init.S
@@ -23,6 +23,7 @@
 #include <asm/arch/imx-regs.h>
 #include <generated/asm-offsets.h>
 #include "mx35pdk.h"
+#include <asm/arch/lowlevel_macro.S>
 
 /*
  * return soc version
@@ -40,91 +41,6 @@
 	addne \ret, \ret, #0x10
 .endm
 
-/*
- * AIPS setup - Only setup MPROTx registers.
- * The PACR default values are good.
- */
-.macro init_aips
-	/*
-	 * Set all MPROTx to be non-bufferable, trusted for R/W,
-	 * not forced to user-mode.
-	 */
-	ldr r0, =AIPS1_BASE_ADDR
-	ldr r1, =AIPS_MPR_CONFIG
-	str r1, [r0, #0x00]
-	str r1, [r0, #0x04]
-	ldr r0, =AIPS2_BASE_ADDR
-	str r1, [r0, #0x00]
-	str r1, [r0, #0x04]
-
-	/*
-	 * Clear the on and off peripheral modules Supervisor Protect bit
-	 * for SDMA to access them. Did not change the AIPS control registers
-	 * (offset 0x20) access type
-	 */
-	ldr r0, =AIPS1_BASE_ADDR
-	ldr r1, =AIPS_OPACR_CONFIG
-	str r1, [r0, #0x40]
-	str r1, [r0, #0x44]
-	str r1, [r0, #0x48]
-	str r1, [r0, #0x4C]
-	str r1, [r0, #0x50]
-	ldr r0, =AIPS2_BASE_ADDR
-	str r1, [r0, #0x40]
-	str r1, [r0, #0x44]
-	str r1, [r0, #0x48]
-	str r1, [r0, #0x4C]
-	str r1, [r0, #0x50]
-.endm
-
-/* MAX (Multi-Layer AHB Crossbar Switch) setup */
-.macro init_max
-	ldr r0, =MAX_BASE_ADDR
-	/* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
-	ldr r1, =MAX_MPR_CONFIG
-	str r1, [r0, #0x000]        /* for S0 */
-	str r1, [r0, #0x100]        /* for S1 */
-	str r1, [r0, #0x200]        /* for S2 */
-	str r1, [r0, #0x300]        /* for S3 */
-	str r1, [r0, #0x400]        /* for S4 */
-	/* SGPCR - always park on last master */
-	ldr r1, =MAX_SGPCR_CONFIG
-	str r1, [r0, #0x010]        /* for S0 */
-	str r1, [r0, #0x110]        /* for S1 */
-	str r1, [r0, #0x210]        /* for S2 */
-	str r1, [r0, #0x310]        /* for S3 */
-	str r1, [r0, #0x410]        /* for S4 */
-	/* MGPCR - restore default values */
-	ldr r1, =MAX_MGPCR_CONFIG
-	str r1, [r0, #0x800]        /* for M0 */
-	str r1, [r0, #0x900]        /* for M1 */
-	str r1, [r0, #0xA00]        /* for M2 */
-	str r1, [r0, #0xB00]        /* for M3 */
-	str r1, [r0, #0xC00]        /* for M4 */
-	str r1, [r0, #0xD00]        /* for M5 */
-.endm
-
-/* M3IF setup */
-.macro init_m3if
-	/* Configure M3IF registers */
-	ldr r1, =M3IF_BASE_ADDR
-	/*
-	* M3IF Control Register (M3IFCTL)
-	* MRRP[0] = L2CC0 not on priority list (0 << 0)	= 0x00000000
-	* MRRP[1] = L2CC1 not on priority list (0 << 0)	= 0x00000000
-	* MRRP[2] = MBX not on priority list (0 << 0)	= 0x00000000
-	* MRRP[3] = MAX1 not on priority list (0 << 0)	= 0x00000000
-	* MRRP[4] = SDMA not on priority list (0 << 0)	= 0x00000000
-	* MRRP[5] = MPEG4 not on priority list (0 << 0)	= 0x00000000
-	* MRRP[6] = IPU1 on priority list (1 << 6)	= 0x00000040
-	* MRRP[7] = IPU2 not on priority list (0 << 0)	= 0x00000000
-	*						------------
-	*						  0x00000040
-	*/
-	ldr r0, =M3IF_CONFIG
-	str r0, [r1]  /* M3IF control reg */
-.endm
-
 /* CPLD on CS5 setup */
 .macro init_debug_board
 	ldr r0, =DBG_BASE_ADDR
@@ -210,38 +126,7 @@
 lowlevel_init:
 	mov r10, lr
 
-	mrc 15, 0, r1, c1, c0, 0
-
-	mrc 15, 0, r0, c1, c0, 1
-	orr r0, r0, #7
-	mcr 15, 0, r0, c1, c0, 1
-	orr r1, r1, #(1<<11)
-
-	/* Set unaligned access enable */
-	orr r1, r1, #(1<<22)
-
-	/* Set low int latency enable */
-	orr r1, r1, #(1<<21)
-
-	mcr 15, 0, r1, c1, c0, 0
-
-	mov r0, #0
-
-	/* Set branch prediction enable */
-	mcr 15, 0, r0, c15, c2, 4
-
-	mcr 15, 0, r0, c7, c7, 0        /* invalidate I cache and D cache */
-	mcr 15, 0, r0, c8, c7, 0        /* invalidate TLBs */
-	mcr 15, 0, r0, c7, c10, 4       /* Drain the write buffer */
-
-	/*
-	 * initializes very early AIPS
-	 * Then it also initializes Multi-Layer AHB Crossbar Switch,
-	 * M3IF
-	 * Also setup the Peripheral Port Remap register inside the core
-	 */
-	ldr r0, =0x40000015        /* start from AIPS 2GB region */
-	mcr p15, 0, r0, c15, c2, 4
+	core_init
 
 	init_aips
 
diff --git a/board/freescale/mx35pdk/mx35pdk.h b/board/freescale/mx35pdk/mx35pdk.h
index 6aeb21835b..f15aa4f7be 100644
--- a/board/freescale/mx35pdk/mx35pdk.h
+++ b/board/freescale/mx35pdk/mx35pdk.h
@@ -26,31 +26,6 @@
 #ifndef __BOARD_MX35_3STACK_H
 #define __BOARD_MX35_3STACK_H
 
-#define AIPS_MPR_CONFIG		0x77777777
-#define AIPS_OPACR_CONFIG	0x00000000
-
-/* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
-#define MAX_MPR_CONFIG		0x00302154
-/* SGPCR - always park on last master */
-#define MAX_SGPCR_CONFIG	0x00000010
-/* MGPCR - restore default values */
-#define MAX_MGPCR_CONFIG	0x00000000
-
-/*
- * M3IF Control Register (M3IFCTL)
- * MRRP[0] = L2CC0 not on priority list (0 << 0) = 0x00000000
- * MRRP[1] = L2CC1 not on priority list (0 << 0) = 0x00000000
- * MRRP[2] = MBX not on priority list (0 << 0)   = 0x00000000
- * MRRP[3] = MAX1 not on priority list (0 << 0)  = 0x00000000
- * MRRP[4] = SDMA not on priority list (0 << 0)  = 0x00000000
- * MRRP[5] = MPEG4 not on priority list (0 << 0) = 0x00000000
- * MRRP[6] = IPU1 on priority list (1 << 6)      = 0x00000040
- * MRRP[7] = IPU2 not on priority list (0 << 0)  = 0x00000000
- *                                               ------------
- *                                                 0x00000040
- */
-#define M3IF_CONFIG	0x00000040
-
 #define DBG_BASE_ADDR		WEIM_CTRL_CS5
 #define DBG_CSCR_U_CONFIG	0x0000D843
 #define DBG_CSCR_L_CONFIG	0x22252521