ls1088a: Add VID support for QDS and RDB platforms

This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.

This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.

Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

1 files changed, 127 insertions, 0 deletions

diff --git a/board/freescale/ls1088a/ls1088a.c b/board/freescale/ls1088a/ls1088a.c
index d12bcaed8f..188f76dcd2 100644
--- a/board/freescale/ls1088a/ls1088a.c
+++ b/board/freescale/ls1088a/ls1088a.c
@@ -19,9 +19,13 @@
 #include <asm/arch-fsl-layerscape/soc.h>
 #include <asm/arch/ppa.h>
 #include <hwconfig.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
 
 #include "../common/qixis.h"
 #include "ls1088a_qixis.h"
+#include "../common/vid.h"
+#include <fsl_immap.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -51,6 +55,16 @@ unsigned long long get_qixis_addr(void)
 }
 #endif
 
+#if defined(CONFIG_VID)
+int init_func_vid(void)
+{
+	if (adjust_vdd(0) < 0)
+		printf("core voltage not adjusted\n");
+
+	return 0;
+}
+#endif
+
 #if !defined(CONFIG_SPL_BUILD)
 int checkboard(void)
 {
@@ -323,6 +337,119 @@ int misc_init_r(void)
 }
 #endif
 
+int i2c_multiplexer_select_vid_channel(u8 channel)
+{
+	return select_i2c_ch_pca9547(channel);
+}
+
+#ifdef CONFIG_TARGET_LS1088AQDS
+/* read the current value(SVDD) of the LTM Regulator Voltage */
+int get_serdes_volt(void)
+{
+	int  ret, vcode = 0;
+	u8 chan = PWM_CHANNEL0;
+
+	/* Select the PAGE 0 using PMBus commands PAGE for VDD */
+	ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
+			PMBUS_CMD_PAGE, 1, &chan, 1);
+	if (ret) {
+		printf("VID: failed to select VDD Page 0\n");
+		return ret;
+	}
+
+	/* Read the output voltage using PMBus command READ_VOUT */
+	ret = i2c_read(I2C_SVDD_MONITOR_ADDR,
+		       PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2);
+	if (ret) {
+		printf("VID: failed to read the volatge\n");
+		return ret;
+	}
+
+	return vcode;
+}
+
+int set_serdes_volt(int svdd)
+{
+	int ret, vdd_last;
+	u8 buff[5] = {0x04, PWM_CHANNEL0, PMBUS_CMD_VOUT_COMMAND,
+			svdd & 0xFF, (svdd & 0xFF00) >> 8};
+
+	/* Write the desired voltage code to the SVDD regulator */
+	ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
+			PMBUS_CMD_PAGE_PLUS_WRITE, 1, (void *)&buff, 5);
+	if (ret) {
+		printf("VID: I2C failed to write to the volatge regulator\n");
+		return -1;
+	}
+
+	/* Wait for the volatge to get to the desired value */
+	do {
+		vdd_last = get_serdes_volt();
+		if (vdd_last < 0) {
+			printf("VID: Couldn't read sensor abort VID adjust\n");
+			return -1;
+		}
+	} while (vdd_last != svdd);
+
+	return 1;
+}
+#else
+int get_serdes_volt(void)
+{
+	return 0;
+}
+
+int set_serdes_volt(int svdd)
+{
+	int ret;
+	u8 brdcfg4;
+
+	printf("SVDD changing of RDB\n");
+
+	/* Read the BRDCFG54 via CLPD */
+	ret = i2c_read(CONFIG_SYS_I2C_FPGA_ADDR,
+		       QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
+	if (ret) {
+		printf("VID: I2C failed to read the CPLD BRDCFG4\n");
+		return -1;
+	}
+
+	brdcfg4 = brdcfg4 | 0x08;
+
+	/* Write to the BRDCFG4 */
+	ret = i2c_write(CONFIG_SYS_I2C_FPGA_ADDR,
+			QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
+	if (ret) {
+		debug("VID: I2C failed to set the SVDD CPLD BRDCFG4\n");
+		return -1;
+	}
+
+	/* Wait for the volatge to get to the desired value */
+	udelay(10000);
+
+	return 1;
+}
+#endif
+
+/* this function disables the SERDES, changes the SVDD Voltage and enables it*/
+int board_adjust_vdd(int vdd)
+{
+	int ret = 0;
+
+	debug("%s: vdd = %d\n", __func__, vdd);
+
+	/* Special settings to be performed when voltage is 900mV */
+	if (vdd == 900) {
+		ret = setup_serdes_volt(vdd);
+		if (ret < 0) {
+			ret = -1;
+			goto exit;
+		}
+	}
+exit:
+	return ret;
+}
+
 int board_init(void)
 {
 	init_final_memctl_regs();