Merge branch 'wd'

3 files changed, 227 insertions, 2 deletions

diff --git a/board/kup/common/pcmcia.c b/board/kup/common/pcmcia.c
new file mode 100644
index 0000000000..1f61a0ecd1
--- /dev/null
+++ b/board/kup/common/pcmcia.c
@@ -0,0 +1,225 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "KUP"
+
+#define KUP4K_PCMCIA_B_3V3 (0x00020000)
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(slot);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(2500);
+
+	/*
+	* Configure Port B pins for
+	* 3 Volts enable
+	*/
+	if (slot) { /* Slot A is built-in */
+		cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
+		cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+		/* remove all power */
+		cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
+	}
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	printf("%s  Slot %c:", slot ? "" : "\n", 'A' + slot);
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		puts (" 5.0V card found: NOT SUPPORTED !!!\n");
+	} else {
+		if(slot)
+			cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+		puts (" 3.3V card found: ");
+	}
+#if 0
+	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
+	cp->cp_pbdir &= ~(0x0020 | 0x0010);
+	cp->cp_pbpar &= ~(0x0020 | 0x0010);
+	udelay(500000);
+#endif
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* remove all power */
+	if (slot)
+		cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "	\
+			PCMCIA_BOARD_MSG	\
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	if (!slot) /* Slot A is not configurable */
+		return 0;
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(slot);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	debug ("PCMCIA power OFF\n");
+	/*
+	* Configure Port B pins for
+	* 3 Volts enable
+	*/
+	cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
+	cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+	/* remove all power */
+	cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
+
+	switch(vcc) {
+		case  0: 		break;
+		case 33:
+			cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+			debug ("PCMCIA powered at 3.3V\n");
+			break;
+		case 50:
+			debug ("PCMCIA: 5Volt vcc not supported\n");
+			break;
+		default:
+			puts("PCMCIA: vcc not supported");
+			break;
+	}
+	udelay(10000);
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
+			       ? "only 5 V --> NOT SUPPORTED"
+	: "can do 3.3V");
+
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/kup/kup4k/Makefile b/board/kup/kup4k/Makefile
index 62d289b436..4a3954c389 100644
--- a/board/kup/kup4k/Makefile
+++ b/board/kup/kup4k/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/kup/kup4x/Makefile b/board/kup/kup4x/Makefile
index 62d289b436..4a3954c389 100644
--- a/board/kup/kup4x/Makefile
+++ b/board/kup/kup4x/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)