Merge branch 'u-boot/master'

Conflicts:
	drivers/net/Makefile

(trivial merge)

1 files changed, 0 insertions, 346 deletions

diff --git a/board/mousse/README b/board/mousse/README
deleted file mode 100644
index d5dda7a8e7..0000000000
--- a/board/mousse/README
+++ /dev/null
@@ -1,346 +0,0 @@
-
-U-Boot for MOUSSE/MPC8240 (KAHLUA)
-----------------------------------
-James Dougherty (jfd@broadcom.com), 09/10/01
-
-The Broadcom/Vooha Mousse board is a 3U Compact PCI system board
-which uses the MPC8240, a 64MB SDRAM SIMM, and has onboard
-DEC 21143, NS16550 UART, an SGS M48T59Y TOD, and 4MB FLASH.
-See also: http://www.vooha.com/
-
-* NVRAM setenv/printenv/savenv supported.
-* Date Command
-* Serial Console support
-* Network support
-* FLASH of kernel images is supported.
-* FLASH of U-Boot to onboard and PLCC boot region.
-* Kernel command line options from NVRAM is supported.
-* IP PNP options supported.
-
-U-Boot Loading...
-
-
-U-Boot 1.0.5 (Sep 10 2001 - 00:22:25)
-
-CPU:   MPC8240 Revision 1.1 at 198 MHz: 16 kB I-Cache 16 kB D-Cache
-Board: MOUSSE MPC8240/KAHLUA - CHRP (MAP B)
-Built: Sep 10 2001 at 01:01:50
-MPLD:  Revision 127
-Local Bus:  33 MHz
-RTC:   M48T589 TOD/NVRAM (8176) bytes
-  Current date/time: 9/10/2001 0:18:52
-DRAM:  64 MB
-FLASH:  1.960 MB
-PCI:    scanning bus0 ...
-  bus dev fn venID devID class  rev MBAR0    MBAR1    IPIN ILINE
-  00  00  00 1057  0003  060000 11  00000008 00000000 01   00
-  00  0d  00 1011  0019  020000 41  80000001 80000000 01   01
-  00  0e  00 105a  4d38  018000 01  a0000001 a0001001 01   03
-In:    serial
-Out:   serial
-Err:   serial
-
-Hit any key to stop autoboot:  0
-=>
-
-I. Root FileSystem/IP Configuration
-
-bootcmd=tftp 100000 vmlinux.img;bootm
-bootdelay=3
-baudrate=9600
-ipaddr=<IP ADDRESS>
-netmask=<NETMASK>
-hostname=<NAME>
-serverip=<NFS SERVER IP ADDRESS>
-ethaddr=00:00:10:20:30:44
-nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs
-gateway=<IP ADDRESS>
-root=/dev/nfs
-stdin=serial
-stdout=serial
-stderr=serial
-
-NVRAM environment variables.
-
-use the command:
-
-setenv <attribute> <value>
-
-type "saveenv" to write to NVRAM.
-
-
-II. To boot from a hard drive:
-
-setenv root /dev/hda1
-
-
-III. IP options which configure the network:
-
-ipaddr=<IP ADDRESS OF MACHINE>
-netmask=<NETMASK>
-hostname=mousse
-ethaddr=00:00:10:20:30:44
-gateway=<IP ADDRESS OF GATEWAY/ROUTER>
-
-
-IV. IP Options which configure NFS Root/Boot Support
-
-root=/dev/nfs
-serverip=<NFS SERVER IP ADDRESS>
-nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs
-
-V. U-Boot Image Support
-
-The U-Boot boot loader assumes that after you build
-your kernel (vmlinux), you will create a U-Boot image
-using the following commands or script:
-
-#!/bin/csh
-/bin/touch vmlinux.img
-/bin/rm vmlinux.img
-set path=($TOOLBASE/bin $path)
-set path=($U_BOOT/tools $path)
-powerpc-linux-objcopy -S -O binary vmlinux vmlinux.bin
-gzip -vf vmlinux.bin
-mkimage -A ppc -O linux -T kernel -C gzip -a 0 -e 0 -n vmlinux.bin.gz -d vmlinux.bin.gz vmlinux.img
-ls -l vmlinux.img
-
-
-VI. ONBOARD FLASH Support
-
-FLASH support is provided for the onboard FLASH chip Bootrom area.
-U-Boot is loaded into either the ROM boot region of the FLASH chip,
-after first being boot-strapped from a pre-progammed AMD29F040 PLCC
-bootrom. The PLCC needs to be programmed with a ROM burner using
-AMD 29F040 ROM parts and the u-boot.bin or u-boot.hex (S-Record)
-images.
-
-The PLCC overlays this same region of flash as the onboard FLASH,
-the jumper J100 is a chip-select for which flash chip you want to
-progam. When jumper J100 is connected to pins 2-3, you boot from
-PLCC FLASH.
-
-To bringup a system, simply flash a flash an AMD29F040 PLCC
-bootrom, and put this in the PLCC socket. Move jumper J100 to
-pins 2-3 and boot from the PLCC.
-
-
-Now, while the system is running, move Jumper J100 to
-pins 1-2 and follow the procedure below to FLASH a bootrom
-(u-boot.bin) image into the onboard bootrom region (AMD29LV160DB):
-
-tftp 100000 u-boot.bin
-protect off FFF00000 FFF7FFFF
-erase FFF00000 FFF7FFFF
-cp.b 100000 FFF00000 \${filesize}\
-
-
-Here is an example:
-
-=>tftp 100000 u-boot.bin
-eth_halt
-eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
-DEC Ethernet iobase=0x80000000
-ARP broadcast 1
-Filename 'u-boot.bin'.
-Load address: 0x100000
-Loading: #########################
-done
-Bytes transferred = 123220 (1e154 hex)
-eth_halt
-=>protect off FFF00000 FFF7FFFF
-Un-Protected 8 sectors
-=>erase FFF00000 FFF7FFFF
-Erase Flash from 0xfff00000 to 0xfff7ffff
-Erase FLASH[PLCC_BOOT] -8 sectors:........ done
-Erased 8 sectors
-=>cp.b 100000 FFF00000 1e154
-Copy to Flash... FLASH[PLCC_BOOT]:..done
-=>
-
-
-B. FLASH RAMDISK REGION
-
-FLASH support is provided for an Onboard 512K RAMDISK region.
-
-TThe following commands will FLASH a bootrom (u-boot.bin) image
-into the onboard FLASH region (AMD29LV160DB 2MB FLASH):
-
-tftp 100000 u-boot.bin
-protect off FFF80000 FFFFFFFF
-erase FFF80000 FFFFFFFF
-cp.b 100000 FFF80000 \${filesize}\
-
-
-C. FLASH KERNEL REGION (960KB)
-
-FLASH support is provided for the 960KB onboard FLASH1 segment.
-This allows flashing of kernel images which U-Boot can load
-and run (standalone) from the onboard FLASH chip. It also assumes
-
-The following commands will FLASH a kernel image to 0xffe10000
-
-tftp 100000 vmlinux.img
-protect off FFE10000 FFEFFFFF
-erase FFE10000 FFEFFFFF
-cp.b 100000 FFE10000 \${filesize}\
-reset
-
-Here is an example:
-
-
-=>tftp 100000 vmlinux.img
-eth_halt
-eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
-DEC Ethernet iobase=0x80000000
-ARP broadcast 1
-TFTP from server 209.128.93.133; our IP address is 209.128.93.138
-Filename 'vmlinux.img'.
-Load address: 0x100000
-Loading: #####################################################################################################################################################
-done
-Bytes transferred = 760231 (b99a7 hex)
-eth_halt
-=>protect off FFE10000 FFEFFFFF
-Un-Protected 15 sectors
-=>erase FFE10000 FFEFFFFF
-Erase Flash from 0xffe10000 to 0xffefffff
-Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done
-Erased 15 sectors
-=>cp.b 100000 FFE10000 b99a7
-Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done
-=>
-
-
-When finished, use the command:
-
-bootm ffe10000
-
-to start the kernel.
-
-Finally, to make this the default boot command, use
-the following commands:
-
-setenv bootcmd bootm ffe10000
-savenv
-
-to make it automatically boot the kernel from FLASH.
-
-
-To go back to development mode (NFS boot)
-
-setenv bootcmd tftp 100000 vmlinux.img\;bootm
-savenv
-
-
-=>tftp 100000 vmlinux.img
-eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
-DEC Ethernet iobase=0x80000000
-ARP broadcast 1
-Filename 'vmlinux.img'.
-Load address: 0x100000
-Loading: ####################################################################################################################################################
-done
-Bytes transferred = 752717 (b7c4d hex)
-eth_halt
-=>protect off FFE10000 FFEFFFFF
-Un-Protected 15 sectors
-=>erase FFE10000 FFEFFFFF
-Erase Flash from 0xffe10000 to 0xffefffff
-Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done
-Erased 15 sectors
-=>cp.b 100000 FFE10000 b7c4d
-Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done
-=>bootm ffe10000
-## Booting image at ffe10000 ...
-   Image Name:   vmlinux.bin.gz
-   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
-   Data Size:    752653 Bytes = 735 kB = 0 MB
-   Load Address: 00000000
-   Entry Point:  00000000
-   Verifying Checksum ... OK
-   Uncompressing Kernel Image ... OK
-Total memory = 64MB; using 0kB for hash table (at 00000000)
-Linux version 2.4.2_hhl20 (jfd@atlantis) (gcc version 2.95.2 19991024 (release)) #597 Wed Sep 5 23:23:23 PDT 2001
-cpu0: MPC8240/KAHLUA : MOUSSE Platform : 64MB RAM: MPLD Rev. 7f
-Sandpoint port (C) 2000, 2001 MontaVista Software, Inc. (source@mvista.com)
-IP PNP: 802.3 Ethernet Address=<0:0:10:20:30:44>
-NOTICE: mounting root file system via NFS
-On node 0 totalpages: 16384
-zone(0): 16384 pages.
-zone(1): 0 pages.
-zone(2): 0 pages.
-time_init: decrementer frequency = 16.665914 MHz
-time_init: MPC8240 PCI Bus frequency = 33.331828 MHz
-Calibrating delay loop... 133.12 BogoMIPS
-Memory: 62436k available (1336k kernel code, 500k data, 88k init, 0k highmem)
-Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
-Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
-Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
-Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
-POSIX conformance testing by UNIFIX
-PCI: Probing PCI hardware
-Linux NET4.0 for Linux 2.4
-Based upon Swansea University Computer Society NET3.039
-Initializing RT netlink socket
-Starting kswapd v1.8
-pty: 256 Unix98 ptys configured
-block: queued sectors max/low 41394kB/13798kB, 128 slots per queue
-Uniform Multi-Platform E-IDE driver Revision: 6.31
-ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
-PDC20262: IDE controller on PCI bus 00 dev 70
-PDC20262: chipset revision 1
-PDC20262: not 100% native mode: will probe irqs later
-PDC20262: ROM enabled at 0x000d0000
-PDC20262: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
-PDC20262: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
-PDC20262: irq=3 dev->irq=3
-    ide0: BM-DMA at 0xbfff00-0xbfff07, BIOS settings: hda:DMA, hdb:DMA
-    ide1: BM-DMA at 0xbfff08-0xbfff0f, BIOS settings: hdc:pio, hdd:pio
-hda: WDC WD300AB-00BVA0, ATA DISK drive
-hdc: SONY CD-RW CRX160E, ATAPI CD/DVD-ROM drive
-ide0 at 0xbfff78-0xbfff7f,0xbfff76 on irq 3
-ide1 at 0xbfff68-0xbfff6f,0xbfff66 on irq 3
-hda: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=58168/16/63, UDMA(66)
-hdc: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache
-Uniform CD-ROM driver Revision: 3.12
-Partition check:
- /dev/ide/host0/bus0/target0/lun0: p1 p2
-hd: unable to get major 3 for hard disk
-udf: registering filesystem
-loop: loaded (max 8 devices)
-Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
-ttyS00 at 0xffe08080 (irq = 4) is a ST16650
-Linux Tulip driver version 0.9.13a (January 20, 2001)
-eth0: Digital DS21143 Tulip rev 65 at 0xbfff80, EEPROM not present, 00:00:10:20:30:44, IRQ 1.
-eth0:  MII transceiver #0 config 3000 status 7829 advertising 01e1.
-NET4: Linux TCP/IP 1.0 for NET4.0
-IP Protocols: ICMP, UDP, TCP
-IP: routing cache hash table of 512 buckets, 4Kbytes
-TCP: Hash tables configured (established 4096 bind 4096)
-NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
-devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
-devfs: boot_options: 0x0
-VFS: Mounted root (nfs filesystem).
-Mounted devfs on /dev
-Freeing unused kernel memory: 88k init 4k openfirmware
-eth0: Setting full-duplex based on MII#0 link partner capability of 45e1.
-INIT: version 2.78 booting
-INIT: Entering runlevel: 2
-
-
-Welcome to Linux/PPC
-MPC8240/MOUSSE
-
-
-mousse login: root
-Password:
-PAM_unix[13]: (login) session opened for user root by LOGIN(uid=0)
-Last login: Thu Sep  6 00:16:51 2001 on console
-
-
-Welcome to Linux/PPC
-MPC8240/MOUSSE
-
-
-mousse#