Initial revision

1 files changed, 350 insertions, 0 deletions

diff --git a/board/mousse/README b/board/mousse/README
new file mode 100644
index 0000000000..ef072bd92f
--- /dev/null
+++ b/board/mousse/README
@@ -0,0 +1,350 @@
+
+U-Boot for MOUSSE/MPC8240 (KAHLUA)
+----------------------------------
+James Dougherty (jfd@broadcom.com), 09/10/01
+
+The Broadcom/Vooha Mousse board is a 3U Compact PCI system board
+which uses the MPC8240, a 64MB SDRAM SIMM, and has onboard
+DEC 21143, NS16550 UART, an SGS M48T59Y TOD, and 4MB FLASH.
+See also: http://www.vooha.com/
+
+* NVRAM setenv/printenv/savenv supported.
+* Date Command
+* Serial Console support
+* Network support
+* FLASH of kernel images is supported.
+* FLASH of U-Boot to onboard and PLCC boot region.
+* Kernel command line options from NVRAM is supported.
+* IP PNP options supported.
+
+U-Boot Loading...
+
+
+
+U-Boot 1.0.5 (Sep 10 2001 - 00:22:25)
+
+CPU:   MPC8240 Revision 1.1 at 198 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MOUSSE MPC8240/KAHLUA - CHRP (MAP B)
+Built: Sep 10 2001 at 01:01:50
+MPLD:  Revision 127
+Local Bus:  33 MHz
+RTC:   M48T589 TOD/NVRAM (8176) bytes
+  Current date/time: 9/10/2001 0:18:52
+DRAM:  64 MB
+FLASH:  1.960 MB
+PCI:    scanning bus0 ...
+  bus dev fn venID devID class  rev MBAR0    MBAR1    IPIN ILINE
+  00  00  00 1057  0003  060000 11  00000008 00000000 01   00
+  00  0d  00 1011  0019  020000 41  80000001 80000000 01   01
+  00  0e  00 105a  4d38  018000 01  a0000001 a0001001 01   03
+In:    serial
+Out:   serial
+Err:   serial
+
+Hit any key to stop autoboot:  0
+=>
+
+I. Root FileSystem/IP Configuration
+
+bootcmd=tftp 100000 vmlinux.img;bootm
+bootdelay=3
+baudrate=9600
+ipaddr=<IP ADDRESS>
+netmask=<NETMASK>
+hostname=<NAME>
+serverip=<NFS SERVER IP ADDRESS>
+ethaddr=00:00:10:20:30:44
+nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs
+gateway=<IP ADDRESS>
+root=/dev/nfs
+stdin=serial
+stdout=serial
+stderr=serial
+
+NVRAM environment variables.
+
+use the command:
+
+setenv <attribute> <value>
+
+type "saveenv" to write to NVRAM.
+
+
+
+II. To boot from a hard drive:
+
+setenv root /dev/hda1
+
+
+III. IP options which configure the network:
+
+ipaddr=<IP ADDRESS OF MACHINE>
+netmask=<NETMASK>
+hostname=mousse
+ethaddr=00:00:10:20:30:44
+gateway=<IP ADDRESS OF GATEWAY/ROUTER>
+
+
+IV. IP Options which configure NFS Root/Boot Support
+
+root=/dev/nfs
+serverip=<NFS SERVER IP ADDRESS>
+nfsroot=<NFS SERVER IP ADDRESS>:/boot/root-fs
+
+V. U-Boot Image Support
+
+The U-Boot boot loader assumes that after you build
+your kernel (vmlinux), you will create a U-Boot image
+using the following commands or script:
+
+#!/bin/csh
+/bin/touch vmlinux.img
+/bin/rm vmlinux.img
+set path=($TOOLBASE/bin $path)
+set path=($U_BOOT/tools $path)
+powerpc-linux-objcopy -S -O binary vmlinux vmlinux.bin
+gzip -vf vmlinux.bin
+mkimage -A ppc -O linux -T kernel -C gzip -a 0 -e 0 -n vmlinux.bin.gz -d vmlinux.bin.gz vmlinux.img
+ls -l vmlinux.img
+
+
+VI. ONBOARD FLASH Support
+
+FLASH support is provided for the onboard FLASH chip Bootrom area.
+U-Boot is loaded into either the ROM boot region of the FLASH chip,
+after first being boot-strapped from a pre-progammed AMD29F040 PLCC
+bootrom. The PLCC needs to be programmed with a ROM burner using
+AMD 29F040 ROM parts and the u-boot.bin or u-boot.hex (S-Record)
+images.
+
+The PLCC overlays this same region of flash as the onboard FLASH,
+the jumper J100 is a chip-select for which flash chip you want to
+progam. When jumper J100 is connected to pins 2-3, you boot from
+PLCC FLASH.
+
+To bringup a system, simply flash a flash an AMD29F040 PLCC
+bootrom, and put this in the PLCC socket. Move jumper J100 to
+pins 2-3 and boot from the PLCC.
+
+
+Now, while the system is running, move Jumper J100 to
+pins 1-2 and follow the procedure below to FLASH a bootrom
+(u-boot.bin) image into the onboard bootrom region (AMD29LV160DB):
+
+tftp 100000 u-boot.bin
+protect off FFF00000 FFF7FFFF
+erase FFF00000 FFF7FFFF
+cp.b 100000 FFF00000 \$(filesize)\
+
+
+Here is an example:
+
+=>tftp 100000 u-boot.bin
+eth_halt
+eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
+DEC Ethernet iobase=0x80000000
+ARP broadcast 1
+Filename 'u-boot.bin'.
+Load address: 0x100000
+Loading: #########################
+done
+Bytes transferred = 123220 (1e154 hex)
+eth_halt
+=>protect off FFF00000 FFF7FFFF
+Un-Protected 8 sectors
+=>erase FFF00000 FFF7FFFF
+Erase Flash from 0xfff00000 to 0xfff7ffff
+Erase FLASH[PLCC_BOOT] -8 sectors:........ done
+Erased 8 sectors
+=>cp.b 100000 FFF00000 1e154
+Copy to Flash... FLASH[PLCC_BOOT]:..done
+=>
+
+
+B. FLASH RAMDISK REGION
+
+FLASH support is provided for an Onboard 512K RAMDISK region.
+
+TThe following commands will FLASH a bootrom (u-boot.bin) image
+into the onboard FLASH region (AMD29LV160DB 2MB FLASH):
+
+tftp 100000 u-boot.bin
+protect off FFF80000 FFFFFFFF
+erase FFF80000 FFFFFFFF
+cp.b 100000 FFF80000 \$(filesize)\
+
+
+
+C. FLASH KERNEL REGION (960KB)
+
+FLASH support is provided for the 960KB onboard FLASH1 segment.
+This allows flashing of kernel images which U-Boot can load
+and run (standalone) from the onboard FLASH chip. It also assumes
+
+The following commands will FLASH a kernel image to 0xffe10000
+
+tftp 100000 vmlinux.img
+protect off FFE10000 FFEFFFFF
+erase FFE10000 FFEFFFFF
+cp.b 100000 FFE10000 \$(filesize)\
+reset
+
+Here is an example:
+
+
+=>tftp 100000 vmlinux.img
+eth_halt
+eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
+DEC Ethernet iobase=0x80000000
+ARP broadcast 1
+TFTP from server 209.128.93.133; our IP address is 209.128.93.138
+Filename 'vmlinux.img'.
+Load address: 0x100000
+Loading: #####################################################################################################################################################
+done
+Bytes transferred = 760231 (b99a7 hex)
+eth_halt
+=>protect off FFE10000 FFEFFFFF
+Un-Protected 15 sectors
+=>erase FFE10000 FFEFFFFF
+Erase Flash from 0xffe10000 to 0xffefffff
+Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done
+Erased 15 sectors
+=>cp.b 100000 FFE10000 b99a7
+Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done
+=>
+
+
+
+When finished, use the command:
+
+bootm ffe10000
+
+to start the kernel.
+
+Finally, to make this the default boot command, use
+the following commands:
+
+setenv bootcmd bootm ffe10000
+savenv
+
+to make it automatically boot the kernel from FLASH.
+
+
+To go back to development mode (NFS boot)
+
+setenv bootcmd tftp 100000 vmlinux.img\;bootm
+savenv
+
+
+=>tftp 100000 vmlinux.img
+eth0: DC21143 Ethernet adapter(bus=0, device=13, func=0)
+DEC Ethernet iobase=0x80000000
+ARP broadcast 1
+Filename 'vmlinux.img'.
+Load address: 0x100000
+Loading: ####################################################################################################################################################
+done
+Bytes transferred = 752717 (b7c4d hex)
+eth_halt
+=>protect off FFE10000 FFEFFFFF
+Un-Protected 15 sectors
+=>erase FFE10000 FFEFFFFF
+Erase Flash from 0xffe10000 to 0xffefffff
+Erase FLASH[F0_SA3(KERNEL)] -15 sectors:............... done
+Erased 15 sectors
+=>cp.b 100000 FFE10000 b7c4d
+Copy to Flash... FLASH[F0_SA3(KERNEL)]:............done
+=>bootm ffe10000
+## Booting image at ffe10000 ...
+   Image Name:   vmlinux.bin.gz
+   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
+   Data Size:    752653 Bytes = 735 kB = 0 MB
+   Load Address: 00000000
+   Entry Point:  00000000
+   Verifying Checksum ... OK
+   Uncompressing Kernel Image ... OK
+Total memory = 64MB; using 0kB for hash table (at 00000000)
+Linux version 2.4.2_hhl20 (jfd@atlantis) (gcc version 2.95.2 19991024 (release)) #597 Wed Sep 5 23:23:23 PDT 2001
+cpu0: MPC8240/KAHLUA : MOUSSE Platform : 64MB RAM: MPLD Rev. 7f
+Sandpoint port (C) 2000, 2001 MontaVista Software, Inc. (source@mvista.com)
+IP PNP: 802.3 Ethernet Address=<0:0:10:20:30:44>
+NOTICE: mounting root file system via NFS
+On node 0 totalpages: 16384
+zone(0): 16384 pages.
+zone(1): 0 pages.
+zone(2): 0 pages.
+time_init: decrementer frequency = 16.665914 MHz
+time_init: MPC8240 PCI Bus frequency = 33.331828 MHz
+Calibrating delay loop... 133.12 BogoMIPS
+Memory: 62436k available (1336k kernel code, 500k data, 88k init, 0k highmem)
+Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
+Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
+Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
+Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
+POSIX conformance testing by UNIFIX
+PCI: Probing PCI hardware
+Linux NET4.0 for Linux 2.4
+Based upon Swansea University Computer Society NET3.039
+Initializing RT netlink socket
+Starting kswapd v1.8
+pty: 256 Unix98 ptys configured
+block: queued sectors max/low 41394kB/13798kB, 128 slots per queue
+Uniform Multi-Platform E-IDE driver Revision: 6.31
+ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
+PDC20262: IDE controller on PCI bus 00 dev 70
+PDC20262: chipset revision 1
+PDC20262: not 100% native mode: will probe irqs later
+PDC20262: ROM enabled at 0x000d0000
+PDC20262: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
+PDC20262: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
+PDC20262: irq=3 dev->irq=3
+    ide0: BM-DMA at 0xbfff00-0xbfff07, BIOS settings: hda:DMA, hdb:DMA
+    ide1: BM-DMA at 0xbfff08-0xbfff0f, BIOS settings: hdc:pio, hdd:pio
+hda: WDC WD300AB-00BVA0, ATA DISK drive
+hdc: SONY CD-RW CRX160E, ATAPI CD/DVD-ROM drive
+ide0 at 0xbfff78-0xbfff7f,0xbfff76 on irq 3
+ide1 at 0xbfff68-0xbfff6f,0xbfff66 on irq 3
+hda: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=58168/16/63, UDMA(66)
+hdc: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache
+Uniform CD-ROM driver Revision: 3.12
+Partition check:
+ /dev/ide/host0/bus0/target0/lun0: p1 p2
+hd: unable to get major 3 for hard disk
+udf: registering filesystem
+loop: loaded (max 8 devices)
+Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
+ttyS00 at 0xffe08080 (irq = 4) is a ST16650
+Linux Tulip driver version 0.9.13a (January 20, 2001)
+eth0: Digital DS21143 Tulip rev 65 at 0xbfff80, EEPROM not present, 00:00:10:20:30:44, IRQ 1.
+eth0:  MII transceiver #0 config 3000 status 7829 advertising 01e1.
+NET4: Linux TCP/IP 1.0 for NET4.0
+IP Protocols: ICMP, UDP, TCP
+IP: routing cache hash table of 512 buckets, 4Kbytes
+TCP: Hash tables configured (established 4096 bind 4096)
+NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
+devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
+devfs: boot_options: 0x0
+VFS: Mounted root (nfs filesystem).
+Mounted devfs on /dev
+Freeing unused kernel memory: 88k init 4k openfirmware
+eth0: Setting full-duplex based on MII#0 link partner capability of 45e1.
+INIT: version 2.78 booting
+INIT: Entering runlevel: 2
+
+
+Welcome to Linux/PPC
+MPC8240/MOUSSE
+
+
+mousse login: root
+Password:
+PAM_unix[13]: (login) session opened for user root by LOGIN(uid=0)
+Last login: Thu Sep  6 00:16:51 2001 on console
+
+
+Welcome to Linux/PPC
+MPC8240/MOUSSE
+
+
+mousse#