Merge git://www.denx.de/git/u-boot into merge

7 files changed, 1303 insertions, 0 deletions

diff --git a/board/netstal/hcu5/Makefile b/board/netstal/hcu5/Makefile
new file mode 100644
index 0000000000..eee310b1a1
--- /dev/null
+++ b/board/netstal/hcu5/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2007 Netstal Maschinen AG
+# Niklaus Giger (ng@netstal.com)
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+vpath flash.c ../common
+COBJS	= $(BOARD).o sdram.o flash.o
+SOBJS	= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/netstal/hcu5/README.txt b/board/netstal/hcu5/README.txt
new file mode 100644
index 0000000000..3118da9e06
--- /dev/null
+++ b/board/netstal/hcu5/README.txt
@@ -0,0 +1,174 @@
+HCU5 configuration details and startup sequence
+
+(C) Copyright 2007 Netstal Maschinen AG
+    Niklaus Giger (Niklaus.Giger@netstal.com)
+
+TODO:
+-----
+- Fix error: Waiting for PHY auto negotiation to complete..... TIMEOUT !
+     - Does not occur if both EMAC are connected
+- Fix RTS/CTS problem (HW?)
+  CONFIG_SERIAL_MULTI/CONFIG_SERIAL_SOFTWARE_FIFO hangs after
+  Switching to interrupt driven serial input mode
+- Make vxWorks start from u-boot. Possible reasons
+    - Does vxWorks need an entry for the Machine Check interrupt like this
+      tlbentry( 0x40000000, SZ_256M, 0, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) ?
+
+Caveats:
+--------
+Errata CHIP_8: Incorrect Write to DDR SDRAM. (was not applied to sequoia.c)
+see hcu5.c.
+
+
+Memory Bank 0 -- Flash chip
+---------------------------
+
+0xfff00000 - 0xffffffff
+
+The flash chip is really only 512Kbytes, but the high address bit of
+the 1Meg region is ignored, so the flash is replicated through the
+region. Thus, this is consistent with a flash base address 0xfff80000.
+
+The placement at the end is to be consistent with reset behavior,
+where the processor itself initially uses this bus to load the branch
+vector and start running.
+
+On-Chip Memory
+--------------
+
+0xe0010000- 0xe0013fff   CFG_OCM_BASE
+The 440EPx includes a 16K on-chip memory that can be placed however
+software chooses.
+
+Internal Peripherals
+--------------------
+
+0xef600300 - 0xef6008ff
+
+These are scattered various peripherals internal to the PPC440EPX
+chip.
+
+Chip-Select 2: Flash Memory
+---------------------------
+
+Not used
+
+Chip-Select 3: CAN Interface
+----------------------------
+0xc800000: 2 Intel 82527 CAN-Controller
+
+
+Chip-Select 4: IMC-bus standard
+-------------------------------
+
+0xcc00000: Netstal specific IO-Bus
+
+
+Chip-Select 5: IMC-bus fast (inactive)
+--------------------------------------
+
+0xce00000: Netstal specific IO-Bus (fast, but not yet used)
+
+
+Memory Bank 1 -- DDR2
+-------------------------------------
+
+0x00000000 - 0xfffffff   # Default 256 MB
+
+PCI ??
+
+USB ??
+Only USB_STORAGE is enabled to load vxWorks
+from a memory stick.
+
+System-LEDs ??? (Analog zu HCU4 ???)
+
+Startup sequence
+----------------
+
+(cpu/ppc4xx/resetvec.S)
+depending on configs option
+call _start_440 _start_pci oder _start
+
+(cpu/ppc4xx/start.S)
+
+_start_440:
+	initialize register like
+	CCR0
+	debug
+	setup interrupt vectors
+	configure cache regions
+	clear and setup TLB
+	enable internal RAM
+	jump start_ram
+	which in turn will jump to start
+_start:
+	Clear and set up some registers.
+	Debug setup
+	Setup the internal SRAM
+	Setup the stack in internal SRAM
+    setup stack pointer (r1)
+    setup GOT
+	call cpu_init_f	/* run low-level CPU init code	   (from Flash) */
+
+    call cpu_init_f
+    board_init_f: (lib_ppc\board.c)
+	init_sequence defines a list of function to be called
+	    board_early_init_f: (board/netstal/hcu5/hcu5.c)
+		We are using Bootstrap-Option A
+		if CPR0_ICFG_RLI_MASK == 0 then set some registers and reboot
+		Setup the GPIO pins
+		Setup the interrupt controller polarities, triggers, etc.
+		Ethernet, PCI, USB enable
+		setup BOOT FLASH (Chip timing)
+	    init_baudrate,
+	    serial_init
+	    checkcpu
+	    misc_init_f #ifdef
+	    init_func_i2c #ifdef
+	    post_init_f  #ifdef
+	    init_func_ram -> calls init_dram board/netstal/hcu5/sdram.c
+		(EYE function removed!!)
+	    test_dram call
+
+	 * Reserve memory at end of RAM for (top down in that order):
+	 *  - kernel log buffer
+	 *  - protected RAM
+	 *  - LCD framebuffer
+	 *  - monitor code
+	 *  - board info struct
+	Save local variables to board info struct
+	call relocate_code() does not return
+	relocate_code: (cpu/ppc4xx/start.S)
+-------------------------------------------------------
+From now on our copy is in RAM and we will run from there,
+	starting with board_init_r
+-------------------------------------------------------
+    board_init_r: (lib_ppc\board.c)
+	setup bd function pointers
+	trap_init
+	flash_init: (board/netstal/hcu5/flash.c)
+		/* setup for u-boot erase, update */
+	setup bd flash info
+	cpu_init_r: (cpu/ppc4xx/cpu_init.c)
+	    peripheral chip select in using defines like
+	    CFG_EBC_PB0A, CFG_EBC_PB0C from hcu5.h
+	mem_malloc_init
+	malloc_bin_reloc
+	spi_init (r or f)??? (CFG_ENV_IS_IN_EEPROM)
+	env_relocated
+	misc_init_r(bd): (board/netstal/hcu5.c)
+	    ethaddr mit serial number ergänzen
+    Then we will somehow go into the command loop
+
+Most of the HW specific code for the HCU5 may be found in
+include/configs/hcu5.h
+board/netstal/hcu5/*
+cpu/ppc4xx/*
+lib_ppc/*
+include/ppc440.h
+
+Drivers for serial etc are found under drivers/
+
+Don't ask question if you did not look at the README !!
+Most CFG_* and CONFIG_* switches are mentioned/explained there.
diff --git a/board/netstal/hcu5/config.mk b/board/netstal/hcu5/config.mk
new file mode 100644
index 0000000000..cfd574412c
--- /dev/null
+++ b/board/netstal/hcu5/config.mk
@@ -0,0 +1,30 @@
+#
+# (C) Copyright 2005 Netstal Maschinen AG
+#     Niklaus Giger (ng@netstal.com)
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Netstal Maschinen AG: HCU5 boards
+#
+
+TEXT_BASE = 0xFFFa0000
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG -g
+endif
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
new file mode 100644
index 0000000000..23df0814ff
--- /dev/null
+++ b/board/netstal/hcu5/hcu5.c
@@ -0,0 +1,525 @@
+/*
+ *(C) Copyright 2005-2007 Netstal Maschinen AG
+ *    Niklaus Giger (Niklaus.Giger@netstal.com)
+ *
+ *    This source code is free software; you can redistribute it
+ *    and/or modify it in source code form under the terms of the GNU
+ *    General Public License as published by the Free Software
+ *    Foundation; either version 2 of the License, or (at your option)
+ *    any later version.
+ *
+ *    This program is distributed in the hope that it will be useful,
+ *    but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *    GNU General Public License for more details.
+ *
+ *    You should have received a copy of the GNU General Public License
+ *    along with this program; if not, write to the Free Software
+ *    Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <ppc440.h>
+#include <asm/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void sysLedSet(u32 value);
+
+extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+#undef BOOTSTRAP_OPTION_A_ACTIVE
+
+#define SDR0_CP440		0x0180
+
+#define SYSTEM_RESET		0x30000000
+#define CHIP_RESET		0x20000000
+
+#define SDR0_ECID0		0x0080
+#define SDR0_ECID1		0x0081
+#define SDR0_ECID2		0x0082
+#define SDR0_ECID3		0x0083
+
+#define SYS_IO_ADDRESS		0xcce00000
+
+#define DEFAULT_ETH_ADDR  "ethaddr"
+/* ethaddr for first or etha1ddr for second ethernet */
+
+enum {
+	/* HW_GENERATION_HCU1 is no longer supported */
+	HW_GENERATION_HCU2  = 0x10,
+	HW_GENERATION_HCU3  = 0x10,
+	HW_GENERATION_HCU4  = 0x20,
+	HW_GENERATION_HCU5  = 0x30,
+	HW_GENERATION_MCU   = 0x08,
+	HW_GENERATION_MCU20 = 0x0a,
+	HW_GENERATION_MCU25 = 0x09,
+};
+
+
+/*
+ * This function is run very early, out of flash, and before devices are
+ * initialized. It is called by lib_ppc/board.c:board_init_f by virtue
+ * of being in the init_sequence array.
+ *
+ * The SDRAM has been initialized already -- start.S:start called
+ * init.S:init_sdram early on -- but it is not yet being used for
+ * anything, not even stack. So be careful.
+ */
+
+int board_early_init_f(void)
+{
+	u32 reg;
+
+#ifdef BOOTSTRAP_OPTION_A_ACTIVE
+	/* Booting with Bootstrap Option A
+	 * First boot, with CPR0_ICFG_RLI_MASK == 0
+	 * no we setup varios boot strapping register,
+	 * then we do reset the PPC440 using a chip reset
+	 * Unfortunately, we cannot use this option, as Nto1 is not set
+	 * with Bootstrap Option A and cannot be changed later on by SW
+	 * There are no other possible boostrap options with a 8 bit ROM
+	 * See Errata (Version 1.04) CHIP_9
+	 */
+
+	u32 cpr0icfg;
+	u32 dbcr;
+
+	mfcpr(CPR0_ICFG, cpr0icfg);
+	if (!(cpr0icfg & CPR0_ICFG_RLI_MASK)) {
+		mtcpr(CPR0_MALD,   0x02000000);
+		mtcpr(CPR0_OPBD,   0x02000000);
+	        mtcpr(CPR0_PERD,   0x05000000);  /* 1:5 */
+		mtcpr(CPR0_PLLC,   0x40000238);
+		mtcpr(CPR0_PLLD,   0x01010414);
+		mtcpr(CPR0_PRIMAD, 0x01000000);
+		mtcpr(CPR0_PRIMBD, 0x01000000);
+		mtcpr(CPR0_SPCID,  0x03000000);
+		mtsdr(SDR0_PFC0,   0x00003E00);  /* [CTE] = 0 */
+		mtsdr(SDR0_CP440,  0x0EAAEA02);  /* [Nto1] = 1*/
+		mtcpr(CPR0_ICFG,   cpr0icfg | CPR0_ICFG_RLI_MASK);
+
+		/*
+		 * Initiate system reset in debug control register DBCR
+		 */
+		dbcr = mfspr(dbcr0);
+		mtspr(dbcr0, dbcr | CHIP_RESET);
+	}
+	mtsdr(SDR0_CP440, 0x0EAAEA02);  /* [Nto1] = 1*/
+#endif
+	mtdcr(ebccfga, xbcfg);
+	mtdcr(ebccfgd, 0xb8400000);
+
+	/*--------------------------------------------------------------------
+	 * Setup the GPIO pins
+	 *-------------------------------------------------------------------*/
+	/* test-only: take GPIO init from pcs440ep ???? in config file */
+	out32(GPIO0_OR, 0x00000000);
+	out32(GPIO0_TCR, 0x7C2FF1CF);
+	out32(GPIO0_OSRL, 0x40055000);
+	out32(GPIO0_OSRH, 0x00000000);
+	out32(GPIO0_TSRL, 0x40055000);
+	out32(GPIO0_TSRH, 0x00000400);
+	out32(GPIO0_ISR1L, 0x40000000);
+	out32(GPIO0_ISR1H, 0x00000000);
+	out32(GPIO0_ISR2L, 0x00000000);
+	out32(GPIO0_ISR2H, 0x00000000);
+	out32(GPIO0_ISR3L, 0x00000000);
+	out32(GPIO0_ISR3H, 0x00000000);
+
+	out32(GPIO1_OR, 0x00000000);
+	out32(GPIO1_TCR, 0xC6007FFF);
+	out32(GPIO1_OSRL, 0x00140000);
+	out32(GPIO1_OSRH, 0x00000000);
+	out32(GPIO1_TSRL, 0x00000000);
+	out32(GPIO1_TSRH, 0x00000000);
+	out32(GPIO1_ISR1L, 0x05415555);
+	out32(GPIO1_ISR1H, 0x40000000);
+	out32(GPIO1_ISR2L, 0x00000000);
+	out32(GPIO1_ISR2H, 0x00000000);
+	out32(GPIO1_ISR3L, 0x00000000);
+	out32(GPIO1_ISR3H, 0x00000000);
+
+	/*--------------------------------------------------------------------
+	 * Setup the interrupt controller polarities, triggers, etc.
+	 *-------------------------------------------------------------------*/
+	mtdcr(uic0sr, 0xffffffff);	/* clear all */
+	mtdcr(uic0er, 0x00000000);	/* disable all */
+	mtdcr(uic0cr, 0x00000005);	/* ATI & UIC1 crit are critical */
+	mtdcr(uic0pr, 0xfffff7ff);	/* per ref-board manual */
+	mtdcr(uic0tr, 0x00000000);	/* per ref-board manual */
+	mtdcr(uic0vr, 0x00000000);	/* int31 highest, base=0x000 */
+	mtdcr(uic0sr, 0xffffffff);	/* clear all */
+
+	mtdcr(uic1sr, 0xffffffff);	/* clear all */
+	mtdcr(uic1er, 0x00000000);	/* disable all */
+	mtdcr(uic1cr, 0x00000000);	/* all non-critical */
+	mtdcr(uic1pr, 0xffffffff);	/* per ref-board manual */
+	mtdcr(uic1tr, 0x00000000);	/* per ref-board manual */
+	mtdcr(uic1vr, 0x00000000);	/* int31 highest, base=0x000 */
+	mtdcr(uic1sr, 0xffffffff);	/* clear all */
+
+	mtdcr(uic2sr, 0xffffffff);	/* clear all */
+	mtdcr(uic2er, 0x00000000);	/* disable all */
+	mtdcr(uic2cr, 0x00000000);	/* all non-critical */
+	mtdcr(uic2pr, 0xffffffff);	/* per ref-board manual */
+	mtdcr(uic2tr, 0x00000000);	/* per ref-board manual */
+	mtdcr(uic2vr, 0x00000000);	/* int31 highest, base=0x000 */
+	mtdcr(uic2sr, 0xffffffff);	/* clear all */
+	mtsdr(sdr_pfc0, 0x00003E00);	/* Pin function:  */
+	mtsdr(sdr_pfc1, 0x00848000);	/* Pin function: UART0 has 4 pins */
+
+	/* PCI arbiter enabled */
+	mfsdr(sdr_pci0, reg);
+	mtsdr(sdr_pci0, 0x80000000 | reg);
+
+	pci_pre_init(0);
+
+	/* setup BOOT FLASH */
+	mtsdr(SDR0_CUST0, 0xC0082350);
+
+	return 0;
+}
+
+int board_pre_init(void)
+{
+	return board_early_init_f();
+}
+
+int checkboard(void)
+{
+	unsigned int j;
+	u16 *hwVersReg    = (u16 *) HCU_HW_VERSION_REGISTER;
+	u16 *boardVersReg = (u16 *) HCU_CPLD_VERSION_REGISTER;
+	u16 generation = *boardVersReg & 0xf0;
+	u16 index      = *boardVersReg & 0x0f;
+	u32 ecid0, ecid1, ecid2, ecid3;
+
+	printf("Netstal Maschinen AG: ");
+	if (generation == HW_GENERATION_HCU3)
+		printf("HCU3: index %d", index);
+	else if (generation == HW_GENERATION_HCU4)
+		printf("HCU4: index %d", index);
+	else if (generation == HW_GENERATION_HCU5)
+		printf("HCU5: index %d", index);
+	printf(" HW 0x%02x\n", *hwVersReg & 0xff);
+	mfsdr(SDR0_ECID0, ecid0);
+	mfsdr(SDR0_ECID1, ecid1);
+	mfsdr(SDR0_ECID2, ecid2);
+	mfsdr(SDR0_ECID3, ecid3);
+
+	printf("Chip ID 0x%x 0x%x 0x%x 0x%x\n", ecid0, ecid1, ecid2, ecid3);
+	for (j = 0;j < 6; j++) {
+		sysLedSet(1 << j);
+		udelay(200 * 1000);
+	}
+
+	return 0;
+}
+
+u32 sysLedGet(void)
+{
+	return in16(SYS_IO_ADDRESS) & 0x3f;
+}
+
+void sysLedSet(u32 value /* value to place in LEDs */)
+{
+	out16(SYS_IO_ADDRESS, value);
+}
+
+/*---------------------------------------------------------------------------+
+ * getSerialNr
+ *---------------------------------------------------------------------------*/
+static u32 getSerialNr(void)
+{
+	u32 *serial = (u32 *)CFG_FLASH_BASE;
+
+	if (*serial == 0xffffffff)
+		return get_ticks();
+
+	return *serial;
+}
+
+
+/*---------------------------------------------------------------------------+
+ * misc_init_r.
+ *---------------------------------------------------------------------------*/
+int misc_init_r(void)
+{
+	char *s = getenv(DEFAULT_ETH_ADDR);
+	char *e;
+	int i;
+	u32 serial = getSerialNr();
+	unsigned long usb2d0cr = 0;
+	unsigned long usb2phy0cr, usb2h0cr = 0;
+	unsigned long sdr0_pfc1;
+
+	for (i = 0; i < 6; ++i) {
+		gd->bd->bi_enetaddr[i] = s ? simple_strtoul(s, &e, 16) : 0;
+		if (s)
+			s = (*e) ? e + 1 : e;
+	}
+
+	if (gd->bd->bi_enetaddr[3] == 0 &&
+	    gd->bd->bi_enetaddr[4] == 0 &&
+	    gd->bd->bi_enetaddr[5] == 0) {
+		char ethaddr[22];
+
+		/* Must be in sync with CONFIG_ETHADDR */
+		gd->bd->bi_enetaddr[0] = 0x00;
+		gd->bd->bi_enetaddr[1] = 0x60;
+		gd->bd->bi_enetaddr[2] = 0x13;
+		gd->bd->bi_enetaddr[3] = (serial >> 16) & 0xff;
+		gd->bd->bi_enetaddr[4] = (serial >>  8) & 0xff;
+		/* byte[5].bit 0 must be zero */
+		gd->bd->bi_enetaddr[5] = (serial >>  0) & 0xfe;
+		sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X\0",
+			gd->bd->bi_enetaddr[0], gd->bd->bi_enetaddr[1],
+			gd->bd->bi_enetaddr[2], gd->bd->bi_enetaddr[3],
+			gd->bd->bi_enetaddr[4], gd->bd->bi_enetaddr[5]) ;
+		printf("%s: Setting eth %s serial 0x%x\n",  __FUNCTION__,
+		       ethaddr, serial);
+		setenv(DEFAULT_ETH_ADDR, ethaddr);
+	}
+
+#ifdef CFG_ENV_IS_IN_FLASH
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
+			    &flash_info[0]);
+
+	/* Env protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    CFG_ENV_ADDR_REDUND,
+			    CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
+			    &flash_info[0]);
+#endif
+
+	/*
+	 * USB stuff...
+	 */
+
+	/* SDR Setting */
+	mfsdr(SDR0_PFC1, sdr0_pfc1);
+	mfsdr(SDR0_USB2D0CR, usb2d0cr);
+	mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+	mfsdr(SDR0_USB2H0CR, usb2h0cr);
+
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;	/*1*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;		/*0*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;		/*1*/
+	usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
+	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;		/*1*/
+
+	/* An 8-bit/60MHz interface is the only possible alternative
+	   when connecting the Device to the PHY */
+	usb2h0cr   = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
+	usb2h0cr   = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;	/*1*/
+
+	/* To enable the USB 2.0 Device function through the UTMI interface */
+	usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
+	usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION;		/*1*/
+
+	sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
+	sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL;		/*0*/
+
+	mtsdr(SDR0_PFC1, sdr0_pfc1);
+	mtsdr(SDR0_USB2D0CR, usb2d0cr);
+	mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+	mtsdr(SDR0_USB2H0CR, usb2h0cr);
+
+	/*clear resets*/
+	udelay(1000);
+	mtsdr(SDR0_SRST1, 0x00000000);
+	udelay(1000);
+	mtsdr(SDR0_SRST0, 0x00000000);
+
+	printf("USB:   Host(int phy) Device(ext phy)\n");
+
+	return 0;
+}
+
+/*************************************************************************
+ *  pci_pre_init
+ *
+ *  This routine is called just prior to registering the hose and gives
+ *  the board the opportunity to check things. Returning a value of zero
+ *  indicates that things are bad & PCI initialization should be aborted.
+ *
+ *	Different boards may wish to customize the pci controller structure
+ *	(add regions, override default access routines, etc) or perform
+ *	certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int pci_pre_init(struct pci_controller *hose)
+{
+	unsigned long addr;
+
+	/*-------------------------------------------------------------------+
+	 * As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
+	 * Workaround: Disable write pipelining to DDR SDRAM by setting
+	 * PLB0_ACR[WRP] = 0.
+	 *-------------------------------------------------------------------*/
+
+	/*-------------------------------------------------------------------+
+	  | Set priority for all PLB3 devices to 0.
+	  | Set PLB3 arbiter to fair mode.
+	  +-------------------------------------------------------------------*/
+	mfsdr(sdr_amp1, addr);
+	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	addr = mfdcr(plb3_acr);
+	/* mtdcr(plb3_acr, addr & ~plb1_acr_wrp_mask); */  /* ngngng */
+	mtdcr(plb3_acr, addr | 0x80000000); /* Sequoia */
+
+	/*-------------------------------------------------------------------+
+	  | Set priority for all PLB4 devices to 0.
+	  +-------------------------------------------------------------------*/
+	mfsdr(sdr_amp0, addr);
+	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	/* mtdcr(plb4_acr, addr & ~plb1_acr_wrp_mask); */  /* ngngng */
+	mtdcr(plb4_acr, addr);  /* Sequoia */
+
+	/*-------------------------------------------------------------------+
+	  | Set Nebula PLB4 arbiter to fair mode.
+	  +-------------------------------------------------------------------*/
+	/* Segment0 */
+	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	/* addr = (addr & ~plb0_acr_wrp_mask); */  /* ngngng */
+	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; /* Sequoia */
+
+	/* mtdcr(plb0_acr, addr); */ /* Sequoia */
+	mtdcr(plb0_acr, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
+
+	/* Segment1 */
+	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~plb1_acr_wrp_mask) ;
+	/* mtdcr(plb1_acr, addr); */ /* Sequoia */
+	mtdcr(plb1_acr, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
+
+	return 1;
+}
+#endif	/* defined(CONFIG_PCI) */
+
+/*************************************************************************
+ *  pci_target_init
+ *
+ *	The bootstrap configuration provides default settings for the pci
+ *	inbound map (PIM). But the bootstrap config choices are limited and
+ *	may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller *hose)
+{
+	/*-------------------------------------------------------------+
+	 * Set up Direct MMIO registers
+	 *-------------------------------------------------------------*/
+	/*-------------------------------------------------------------+
+	  | PowerPC440EPX PCI Master configuration.
+	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
+	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address
+	  |		  0xA0000000-0xDFFFFFFF
+	  |   Use byte reversed out routines to handle endianess.
+	  | Make this region non-prefetchable.
+	  +-------------------------------------------------------------*/
+	/* PMM0 Mask/Attribute - disabled b4 setting */
+	out32r(PCIX0_PMM0MA, 0x00000000);
+	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
+	/* PMM0 PCI Low Address */
+	out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE);
+	out32r(PCIX0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
+	/* 512M + No prefetching, and enable region */
+	out32r(PCIX0_PMM0MA, 0xE0000001);
+
+	/* PMM0 Mask/Attribute - disabled b4 setting */
+	out32r(PCIX0_PMM1MA, 0x00000000);
+	out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2);	/* PMM0 Local Address */
+	/* PMM0 PCI Low Address */
+	out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2);
+	out32r(PCIX0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
+	/* 512M + No prefetching, and enable region */
+	out32r(PCIX0_PMM1MA, 0xE0000001);
+
+	out32r(PCIX0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
+	out32r(PCIX0_PTM1LA, 0);	/* Local Addr. Reg */
+	out32r(PCIX0_PTM2MS, 0);	/* Memory Size/Attribute */
+	out32r(PCIX0_PTM2LA, 0);	/* Local Addr. Reg */
+
+	/*------------------------------------------------------------------+
+	 * Set up Configuration registers
+	 *------------------------------------------------------------------*/
+
+	/* Program the board's subsystem id/vendor id */
+	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
+			      CFG_PCI_SUBSYS_VENDORID);
+	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
+
+	/* Configure command register as bus master */
+	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
+
+	/* 240nS PCI clock */
+	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
+
+	/* No error reporting */
+	pci_write_config_word(0, PCI_ERREN, 0);
+
+	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+}
+#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+/*************************************************************************
+ *  pci_master_init
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
+void pci_master_init(struct pci_controller *hose)
+{
+	unsigned short temp_short;
+
+	/*---------------------------------------------------------------+
+	  | Write the PowerPC440 EP PCI Configuration regs.
+	  |   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
+	  |   Enable PowerPC440 EP to act as a PCI memory target (PTM).
+	  +--------------------------------------------------------------*/
+	pci_read_config_word(0, PCI_COMMAND, &temp_short);
+	pci_write_config_word(0, PCI_COMMAND,
+			      temp_short | PCI_COMMAND_MASTER |
+			      PCI_COMMAND_MEMORY);
+}
+#endif
+/* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */
+
+/*************************************************************************
+ *  is_pci_host
+ *
+ *	This routine is called to determine if a pci scan should be
+ *	performed. With various hardware environments (especially cPCI and
+ *	PPMC) it's insufficient to depend on the state of the arbiter enable
+ *	bit in the strap register, or generic host/adapter assumptions.
+ *
+ *	Rather than hard-code a bad assumption in the general 440 code, the
+ *	440 pci code requires the board to decide at runtime.
+ *
+ *	Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int is_pci_host(struct pci_controller *hose)
+{
+	return 1;
+}
+#endif				/* defined(CONFIG_PCI) */
diff --git a/board/netstal/hcu5/init.S b/board/netstal/hcu5/init.S
new file mode 100644
index 0000000000..5ab6cd24d7
--- /dev/null
+++ b/board/netstal/hcu5/init.S
@@ -0,0 +1,79 @@
+/*
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+#include <asm/mmu.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+	.section .bootpg,"ax"
+	.globl tlbtab
+
+tlbtab:
+	tlbtab_start
+
+	/* vxWorks needs this entry for the Machine Check interrupt,  */
+	/* tlbentry( 0x40000000, SZ_256M, 0, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) */
+
+	/*
+	 * BOOT_CS (FLASH) must be second. Before relocation SA_I can be off to use the
+	 * speed up boot process. It is patched after relocation to enable SA_I
+	 */
+	tlbentry( CFG_BOOT_BASE_ADDR, SZ_1M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G )
+
+	/* TLB-entry for PCI Memory */
+	tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I )
+
+	/* TLB-entry for EBC (CFG_CPLD) */
+	/* tlbentry( CFG_CPLD, SZ_1K, CFG_CPLD, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) */
+	/* 		CAN */
+	tlbentry( CFG_CS_1, SZ_16M, CFG_CS_1, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+	 /* 		IMC + CPLD */
+	tlbentry( CFG_CS_2, SZ_16M, CFG_CS_2, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+	tlbentry( CFG_CS_2 + 0x1000000, SZ_16M, CFG_CS_2 + 0x1000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+	 /* 		IMC-Fast */
+	tlbentry( CFG_CS_3, SZ_16M, CFG_CS_3, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+	tlbentry( CFG_CS_3 + 0x1000000, SZ_16M, CFG_CS_3 + 0x1000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* TLB-entry for Internal Registers & OCM */
+	tlbentry( CFG_PCI_BASE, SZ_16M, 0xe0000000, 0,  AC_R|AC_W|AC_X|SA_I )
+
+	/*TLB-entry PCI registers*/
+	tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1,  AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* TLB-entry for peripherals */
+	tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I)
+
+	/* TLB for SDRAM will be added by initdram (sdram.c) */
+
+	tlbtab_end
diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c
new file mode 100644
index 0000000000..40391958d2
--- /dev/null
+++ b/board/netstal/hcu5/sdram.c
@@ -0,0 +1,302 @@
+/*
+ * (C) Copyright 2007
+ * Niklaus Giger (Niklaus.Giger@netstal.com)
+ * (C) Copyright 2006
+ * Sylvie Gohl,             AMCC/IBM, gohl.sylvie@fr.ibm.com
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Thierry Roman,           AMCC/IBM, thierry_roman@fr.ibm.com
+ * Alain Saurel,            AMCC/IBM, alain.saurel@fr.ibm.com
+ * Robert Snyder,           AMCC/IBM, rob.snyder@fr.ibm.com
+ *
+ * (C) Copyright 2006
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* define DEBUG for debug output */
+#undef DEBUG
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/mmu.h>
+#include <ppc440.h>
+
+void sysLedSet(u32 value);
+void dcbz_area(u32 start_address, u32 num_bytes);
+void dflush(void);
+
+#define DDR_DCR_BASE 0x10
+#define ddrcfga  (DDR_DCR_BASE+0x0)   /* DDR configuration address reg */
+#define ddrcfgd  (DDR_DCR_BASE+0x1)   /* DDR configuration data reg    */
+
+#define DDR0_01_INT_MASK_MASK             0x000000FF
+#define DDR0_00_INT_ACK_ALL               0x7F000000
+#define DDR0_01_INT_MASK_ALL_ON           0x000000FF
+#define DDR0_01_INT_MASK_ALL_OFF          0x00000000
+
+#define DDR0_17_DLLLOCKREG_MASK           0x00010000 /* Read only */
+#define DDR0_17_DLLLOCKREG_UNLOCKED       0x00000000
+#define DDR0_17_DLLLOCKREG_LOCKED         0x00010000
+
+#define DDR0_22                         0x16
+/* ECC */
+#define DDR0_22_CTRL_RAW_MASK             0x03000000
+#define DDR0_22_CTRL_RAW_ECC_DISABLE      0x00000000 /* ECC not enabled */
+#define DDR0_22_CTRL_RAW_ECC_CHECK_ONLY   0x01000000 /* ECC no correction */
+#define DDR0_22_CTRL_RAW_NO_ECC_RAM       0x02000000 /* Not a ECC RAM*/
+#define DDR0_22_CTRL_RAW_ECC_ENABLE       0x03000000 /* ECC correcting on */
+#define DDR0_03_CASLAT_DECODE(n)            ((((unsigned long)(n))>>16)&0x7)
+
+#ifdef CFG_ENABLE_SDRAM_CACHE
+#define MY_TLB_WORD2_I_ENABLE	0		/* enable caching on DDR2 */
+#else
+#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on DDR2 */
+#endif
+
+void program_tlb(u32 phys_addr, u32 virt_addr, u32 size, u32 tlb_word2_i_value);
+
+#ifdef CONFIG_ADD_RAM_INFO
+void board_add_ram_info(int use_default)
+{
+	PPC440_SYS_INFO board_cfg;
+	u32 val;
+	mfsdram(DDR0_22, val);
+	val &= DDR0_22_CTRL_RAW_MASK;
+	switch (val) {
+	case DDR0_22_CTRL_RAW_ECC_DISABLE:
+		puts(" (ECC disabled");
+		break;
+	case DDR0_22_CTRL_RAW_ECC_CHECK_ONLY:
+		puts(" (ECC check only");
+		break;
+	case DDR0_22_CTRL_RAW_NO_ECC_RAM:
+		puts(" (no ECC ram");
+		break;
+	case DDR0_22_CTRL_RAW_ECC_ENABLE:
+		puts(" (ECC enabled");
+		break;
+	}
+
+	get_sys_info(&board_cfg);
+	printf(", %d MHz", (board_cfg.freqPLB * 2) / 1000000);
+
+	mfsdram(DDR0_03, val);
+	val = DDR0_03_CASLAT_DECODE(val);
+	printf(", CL%d)", val);
+}
+#endif
+
+/*--------------------------------------------------------------------
+ * wait_for_dlllock.
+ *--------------------------------------------------------------------*/
+static int wait_for_dlllock(void)
+{
+	unsigned long val;
+	int wait = 0;
+
+	/* -----------------------------------------------------------+
+	 * Wait for the DCC master delay line to finish calibration
+	 * ----------------------------------------------------------*/
+	mtdcr(ddrcfga, DDR0_17);
+	val = DDR0_17_DLLLOCKREG_UNLOCKED;
+
+	while (wait != 0xffff) {
+		val = mfdcr(ddrcfgd);
+		if ((val & DDR0_17_DLLLOCKREG_MASK) ==
+		    DDR0_17_DLLLOCKREG_LOCKED)
+			/* dlllockreg bit on */
+			return 0;
+		else
+			wait++;
+	}
+	debug("0x%04x: DDR0_17 Value (dlllockreg bit): 0x%08x\n", wait, val);
+	debug("Waiting for dlllockreg bit to raise\n");
+
+	return -1;
+}
+
+/***********************************************************************
+ *
+ * sdram_panic -- Panic if we cannot configure the sdram correctly
+ *
+ ************************************************************************/
+void sdram_panic(const char *reason)
+{
+	printf("\n%s: reason %s",  __FUNCTION__,  reason);
+	sysLedSet(0xff);
+	while (1) {
+	}
+	/* Never return */
+}
+
+#ifdef CONFIG_DDR_ECC
+static void blank_string(int size)
+{
+	int i;
+
+	for (i=0; i<size; i++)
+		putc('\b');
+	for (i=0; i<size; i++)
+		putc(' ');
+	for (i=0; i<size; i++)
+		putc('\b');
+}
+/*---------------------------------------------------------------------------+
+ * program_ecc.
+ *---------------------------------------------------------------------------*/
+static void program_ecc(unsigned long start_address, unsigned long num_bytes,
+			unsigned long tlb_word2_i_value)
+{
+	unsigned long current_address= start_address;
+	int loopi = 0;
+	u32 val;
+
+	char str[] = "ECC generation -";
+	char slash[] = "\\|/-\\|/-";
+
+	sync();
+	eieio();
+
+	puts(str);
+
+	if (tlb_word2_i_value == TLB_WORD2_I_ENABLE) {
+		/* ECC bit set method for non-cached memory */
+		/* This takes various seconds */
+		for(current_address = 0; current_address < num_bytes;
+		     current_address += sizeof(u32)) {
+			*(u32 *)current_address = 0;
+			if ((current_address % (2 << 20)) == 0) {
+				putc('\b');
+				putc(slash[loopi++ % 8]);
+			}
+		}
+	} else {
+		/* ECC bit set method for cached memory */
+		/* Fast method, no noticeable delay */
+		dcbz_area(start_address, num_bytes);
+		dflush();
+	}
+	blank_string(strlen(str));
+
+	/* Clear error status */
+	mfsdram(DDR0_00, val);
+	mtsdram(DDR0_00, val | DDR0_00_INT_ACK_ALL);
+
+	/* Set 'int_mask' parameter to functionnal value */
+	mfsdram(DDR0_01, val);
+	mtsdram(DDR0_01, ((val &~ DDR0_01_INT_MASK_MASK) |
+			  DDR0_01_INT_MASK_ALL_OFF));
+
+	return;
+}
+
+#endif
+
+/***********************************************************************
+ *
+ * initdram -- 440EPx's DDR controller is a DENALI Core
+ *
+ ************************************************************************/
+long int initdram (int board_type)
+{
+#define	HCU_HW_SDRAM_CONFIG_MASK 0x7
+#define INVALID_HW_CONFIG   "Invalid HW-Config"
+	u16 *hwVersReg = (u16 *) HCU_HW_VERSION_REGISTER;
+	unsigned int dram_size = 0;
+
+	mtsdram(DDR0_02, 0x00000000);
+
+	/* Values must be kept in sync with Excel-table <<A0001492.>> ! */
+	mtsdram(DDR0_00, 0x0000190A);
+	mtsdram(DDR0_01, 0x01000000);
+	mtsdram(DDR0_03, 0x02030602);
+	mtsdram(DDR0_04, 0x0A020200);
+	mtsdram(DDR0_05, 0x02020307);
+	switch (*hwVersReg & HCU_HW_SDRAM_CONFIG_MASK) {
+	case 0:
+		dram_size = 128 * 1024 * 1024 ;
+		mtsdram(DDR0_06, 0x0102C80D);  /* 128MB RAM */
+		mtsdram(DDR0_11, 0x000FC800);  /* 128MB RAM */
+		mtsdram(DDR0_43, 0x030A0300);  /* 128MB RAM */
+		break;
+	case 1:
+		dram_size = 256 * 1024 * 1024 ;
+		mtsdram(DDR0_06, 0x0102C812);  /* 256MB RAM */
+		mtsdram(DDR0_11, 0x0014C800);  /* 256MB RAM */
+		mtsdram(DDR0_43, 0x030A0200);  /* 256MB RAM */
+		break;
+	default:
+		sdram_panic(INVALID_HW_CONFIG);
+		break;
+	}
+	dram_size -= 16 * 1024 * 1024;
+	mtsdram(DDR0_07, 0x00090100);
+	/*
+	 * TCPD=200 cycles of clock input is required to lock the DLL.
+	 * CKE must be HIGH the entire time.mtsdram(DDR0_08, 0x02C80001);
+	 */
+	mtsdram(DDR0_08, 0x02C80001);
+	mtsdram(DDR0_09, 0x00011D5F);
+	mtsdram(DDR0_10, 0x00000100);
+	mtsdram(DDR0_12, 0x00000003);
+	mtsdram(DDR0_14, 0x00000000);
+	mtsdram(DDR0_17, 0x1D000000);
+	mtsdram(DDR0_18, 0x1D1D1D1D);
+	mtsdram(DDR0_19, 0x1D1D1D1D);
+	mtsdram(DDR0_20, 0x0B0B0B0B);
+	mtsdram(DDR0_21, 0x0B0B0B0B);
+	#define ECC_RAM  0x03267F0B
+	#define NO_ECC_RAM  0x00267F0B
+#ifdef CONFIG_DDR_ECC
+	mtsdram(DDR0_22, ECC_RAM);
+#else
+	mtsdram(DDR0_22, NO_ECC_RAM);
+#endif
+
+	mtsdram(DDR0_23, 0x00000000);
+	mtsdram(DDR0_24, 0x01020001);
+	mtsdram(DDR0_26, 0x2D930517);
+	mtsdram(DDR0_27, 0x00008236);
+	mtsdram(DDR0_28, 0x00000000);
+	mtsdram(DDR0_31, 0x00000000);
+	mtsdram(DDR0_42, 0x01000006);
+	mtsdram(DDR0_44, 0x00000003);
+	mtsdram(DDR0_02, 0x00000001);
+	wait_for_dlllock();
+	mtsdram(DDR0_00, 0x40000000);  /* Zero init bit */
+
+	/*
+	 * Program tlb entries for this size (dynamic)
+	 */
+	program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE);
+
+	/*
+	 * Setup 2nd TLB with same physical address but different virtual
+	 * address with cache enabled. This is done for fast ECC generation.
+	 */
+	program_tlb(0, CFG_DDR_CACHED_ADDR, dram_size, 0);
+
+#ifdef CONFIG_DDR_ECC
+	/*
+	 * If ECC is enabled, initialize the parity bits.
+	 */
+	program_ecc(CFG_DDR_CACHED_ADDR, dram_size, 0);
+#endif
+
+	return (dram_size);
+}
diff --git a/board/netstal/hcu5/u-boot.lds b/board/netstal/hcu5/u-boot.lds
new file mode 100644
index 0000000000..6d255a94ea
--- /dev/null
+++ b/board/netstal/hcu5/u-boot.lds
@@ -0,0 +1,144 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+
+  ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified.");
+
+  _end = . ;
+  PROVIDE (end = .);
+}