doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 57 insertions, 0 deletions

diff --git a/board/sbc8560/README b/board/sbc8560/README
new file mode 100644
index 0000000000..c4b642236e
--- /dev/null
+++ b/board/sbc8560/README
@@ -0,0 +1,57 @@
+The port was tested on Wind River System Sbc8560 board
+<www.windriver.com>. U-Boot was installed on the flash memory of the
+CPU card (no the SODIMM).
+
+NOTE: Please configure uboot compile to the proper PCI frequency and
+setup the appropriate DIP switch settings.
+
+SBC8560 board:
+
+Make sure boards switches are set to their appropriate conditions.
+Refer to the Engineering Reference Guide ERG-00300-002. Of particular
+importance are: 1) the settings for JP4 (JP4 1-3 and 2-4), which
+select the on-board FLASH device (Intel 28F128Jx); 2) The settings
+for the Clock SW9 (33 MHz or 66 MHz).
+
+	Note:	SW9 Settings: 66 MHz
+		4:1 ratio CCB clocks:SYSCLK
+		3:1 ration e500 Core:CCB
+		pos1 - on, pos2 - on, pos3 - off, pos4 - on, pos5 - off, pos6 - on
+	Note:	SW9 Settings: 33 MHz
+		8:1 ratio CCB clocks:SYSCLK
+		3:1 ration e500 Core:CCB
+		pos1 - on, pos2 - on, pos3 - on, pos4 - off, pos5 - off, pos6 - on
+
+
+Flashing the FLASH device with the "Wind River ICE":
+
+1) Properly connect and configure the Wind River ICE to the target
+   JTAG port. This includes running the SBC8560 register script. Make
+   sure target memory can be read and written.
+
+2) Build the u-boot image:
+	make distclean
+	make SBC8560_66_config or SBC8560_33_config
+	make CROSS_COMPILE=.../ELDK3.0/ppc_8xx-/ all
+
+   Note: reference is made to the ELDK3.0 compiler. Further, it seems
+	 the ppc_8xx compiler is required for the 85xx (no 85xx
+	 designated compiler in ELDK3.0)
+
+3) Convert the uboot (.elf) file to a uboot.bin file (using
+   visionClick converter). The bin file should be converted from
+   fffc0000 to ffffffff
+
+4) Setup the Flash Utility (tools menu) for:
+
+   Do a "dc clr" [visionClick] to load the default register settings
+   Determine the clock speed of the PCI bus and set SW9 accordingly
+	Note: the speed of the PCI bus defaults to the slowest PCI card
+   PlayBack the "default" register file for the SBC8560
+   Select the uboot.bin file with zero bias
+   Select the initialize Target prior to programming
+   Select the V28F640Jx (8192 x 8) 1 device FLASH Algorithm
+   Select the erase base address from FFFC0000 to FFFFFFFF
+   Select the start address from 0 with size of 4000
+
+5) Erase and Program