Raname solidcard3 into sc3; add redundant env for sc3

1 files changed, 382 insertions, 0 deletions

diff --git a/board/sc3/init.S b/board/sc3/init.S
new file mode 100644
index 0000000000..e7b3c83949
--- /dev/null
+++ b/board/sc3/init.S
@@ -0,0 +1,382 @@
+/*------------------------------------------------------------------------------+
+ *
+ *	 This souce code has been made available to you by EuroDesign
+ *	 (www.eurodsn.de). It's based on the original IBM source code, so
+ *	 this follows:
+ *
+ *	 This source code has been made available to you by IBM on an AS-IS
+ *	 basis.  Anyone receiving this source is licensed under IBM
+ *	 copyrights to use it in any way he or she deems fit, including
+ *	 copying it, modifying it, compiling it, and redistributing it either
+ *	 with or without modifications.  No license under IBM patents or
+ *	 patent applications is to be implied by the copyright license.
+ *
+ *	 Any user of this software should understand that IBM cannot provide
+ *	 technical support for this software and will not be responsible for
+ *	 any consequences resulting from the use of this software.
+ *
+ *	 Any person who transfers this source code or any derivative work
+ *	 must include the IBM copyright notice, this paragraph, and the
+ *	 preceding two paragraphs in the transferred software.
+ *
+ *	 COPYRIGHT   I B M   CORPORATION 1995
+ *	 LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
+ *------------------------------------------------------------------------------- */
+
+#include <config.h>
+#include <ppc4xx.h>
+
+#define _LINUX_CONFIG_H 1	/* avoid reading Linux autoconf.h file	*/
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+
+#include <asm/cache.h>
+#include <asm/mmu.h>
+
+/**
+ * ext_bus_cntlr_init - Initializes the External Bus Controller for the external peripherals
+ *
+ * IMPORTANT: For pass1 this code must run from cache since you can not
+ * reliably change a peripheral banks timing register (pbxap) while running
+ * code from that bank. For ex., since we are running from ROM on bank 0, we
+ * can NOT execute the code that modifies bank 0 timings from ROM, so
+ * we run it from cache.
+ *
+ * Bank 0 - Boot-Flash
+ * Bank 1 - NAND-Flash
+ * Bank 2 - ISA bus
+ * Bank 3 - Second Flash
+ * Bank 4 - USB controller
+ */
+	.globl ext_bus_cntlr_init
+ext_bus_cntlr_init:
+/*
+ * We need the current boot up configuration to set correct
+ * timings into internal flash and external flash
+ */
+		mfdcr r24,strap			/* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx
+						   0 0 -> 8 bit external ROM
+						   0 1 -> 16 bit internal ROM */
+		addi r4,0,2
+		srw r24,r24,r4				/* shift right r24 two positions */
+		andi. r24,r24,0x06000
+/*
+ * All calculations are based on 33MHz EBC clock.
+ *
+ * First, create a "very slow" timing (~250ns) with burst mode enabled
+ * This is need for the external flash access
+ */
+		lis r25,0x0800
+		ori r25,r25,0x0280			/* 0000 1000 0xxx 0000 0000 0010 100x xxxx = 0x03800280
+/*
+ * Second, create a fast timing:
+ * 90ns first cycle - 3 clock access
+ * and 90ns burst cycle, plus 1 clock after the last access
+ * This is used for the internal access
+ */
+		lis r26,0x8900
+		ori r26,r26,0x0280			/* 1000 1001 0xxx 0000 0000 0010 100x xxxx
+/*
+ * We can't change settings on CS# if we currently use them.
+ * -> load a few instructions into cache and run this code from cache
+ */
+		mflr r4					/* save link register */
+		bl ..getAddr
+..getAddr:
+		mflr r3					/* get address of ..getAddr */
+		mtlr r4					/* restore link register */
+		addi r4,0,14				/* set ctr to 10; used to prefetch */
+		mtctr r4				/* 10 cache lines to fit this function
+							in cache (gives us 8x10=80 instructions) */
+..ebcloop:
+		icbt r0,r3				/* prefetch cache line for addr in r3 */
+		addi r3,r3,32				/* move to next cache line */
+		bdnz ..ebcloop				/* continue for 10 cache lines */
+/*
+ * Delay to ensure all accesses to ROM are complete before changing
+ * bank 0 timings. 200usec should be enough.
+ * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
+ */
+		lis r3,0x0
+		ori r3,r3,0xA000			/* ensure 200usec have passed since reset */
+		mtctr r3
+..spinlp:
+		bdnz ..spinlp				/* spin loop */
+
+/*-----------------------------------------------------------------------
+ * Memory Bank 0 (BOOT-ROM) initialization
+ * 0xFFEF00000....0xFFFFFFF
+ * We only have to change the timing. Mapping is ok by boot-strapping
+ *----------------------------------------------------------------------- */
+
+		li r4,pb0ap				/* PB0AP=Peripheral Bank 0 Access Parameters */
+		mtdcr ebccfga,r4
+
+		mr r4,r26				/* assume internal fast flash is boot flash */
+		cmpwi r24,0x2000			/* assumption true? ... */
+		beq 1f					/* ...yes! */
+		mr r4,r25				/* ...no, use the slow variant */
+		mr r25,r26				/* use this for the other flash */
+1:
+		mtdcr ebccfgd,r4			/* change timing now */
+
+		li r4,pb0cr				/* PB0CR=Peripheral Bank 0 Control Register */
+		mtdcr ebccfga,r4
+		mfdcr r4,ebccfgd
+		lis r3,0x0001
+		ori r3,r3,0x8000			/* allow reads and writes */
+		or r4,r4,r3
+		mtdcr ebccfgd,r4
+
+/*-----------------------------------------------------------------------
+ * Memory Bank 3 (Second-Flash) initialization
+ * 0xF0000000...0xF01FFFFF -> 2MB
+ *----------------------------------------------------------------------- */
+
+		li r4,pb3ap				/* Peripheral Bank 1 Access Parameter */
+		mtdcr ebccfga,r4
+		mtdcr ebccfgd,r2			/* change timing */
+
+		li r4,pb3cr				/* Peripheral Bank 1 Configuration Registers */
+		mtdcr ebccfga,r4
+
+		lis r4,0xF003
+		ori r4,r4,0x8000
+/*
+ * Consider boot configuration
+ */
+		xori r24,r24,0x2000			/* invert current bus width */
+		or r4,r4,r24
+		mtdcr ebccfgd,r4
+
+/*-----------------------------------------------------------------------
+ * Memory Bank 1 (NAND-Flash) initialization
+ * 0x77D00000...0x77DFFFFF -> 1MB
+ * - the write/read pulse to the NAND can be as short as 25ns, bus the cycle time is always 50ns
+ * - the setup time is 0ns
+ * - the hold time is 15ns
+ * ->
+ *   - TWT = 0
+ *   - CSN = 0
+ *   - OEN = 0
+ *   - WBN = 0
+ *   - WBF = 0
+ *   - TH  = 1
+ * ----> 2 clocks per cycle = 60ns cycle (30ns active, 30ns hold)
+ *----------------------------------------------------------------------- */
+
+		li r4,pb1ap				/* Peripheral Bank 1 Access Parameter */
+		mtdcr ebccfga,r4
+
+		lis r4,0x0000
+		ori r4,r4,0x0200
+		mtdcr ebccfgd,r4
+
+		li r4,pb1cr				/* Peripheral Bank 1 Configuration Registers */
+		mtdcr ebccfga,r4
+
+		lis r4,0x77D1
+		ori r4,r4,0x8000
+		mtdcr ebccfgd,r4
+
+
+/* USB init (without acceleration) */
+#ifndef CONFIG_ISP1161_PRESENT
+		li r4,pb4ap				/* PB4AP=Peripheral Bank 4 Access Parameters */
+		mtdcr ebccfga,r4
+		lis r4,0x0180
+		ori r4,r4,0x5940
+		mtdcr ebccfgd,r4
+#endif
+
+/*-----------------------------------------------------------------------
+ * Memory Bank 2 (ISA Access) initialization (plus memory bank 6 and 7)
+ * 0x78000000...0x7BFFFFFF -> 64 MB
+ * Wir arbeiten bei 33 MHz -> 30ns
+ *-----------------------------------------------------------------------
+
+ A7 (ppc notation) or A24 (standard notation) decides about
+ the type of access:
+ A7/A24=0 -> memory cycle
+ A7/ /A24=1 -> I/O cycle
+*/
+		li r4,pb2ap				/* PB2AP=Peripheral Bank 2 Access Parameters */
+		mtdcr ebccfga,r4
+/*
+ We emulate an ISA access
+
+ 1. Address active
+ 2. wait 0 EBC clocks -> CSN=0
+ 3. set CS#
+ 4. wait 0 EBC clock -> OEN/WBN=0
+ 5. set OE#/WE#
+ 6. wait 4 clocks (ca. 90ns) and for Ready signal
+ 7. hold for 4 clocks -> TH=4
+*/
+
+#if 1
+/* faster access to isa-bus */
+		lis r4,0x0180
+		ori r4,r4,0x5940
+#else
+		lis r4,0x0100
+		ori r4,r4,0x0340
+#endif
+		mtdcr ebccfgd,r4
+
+#ifdef IDE_USES_ISA_EMULATION
+		li r25,pb5ap				/* PB5AP=Peripheral Bank 5 Access Parameters */
+		mtdcr ebccfga,r25
+		mtdcr ebccfgd,r4
+#endif
+
+		li r25,pb6ap				/* PB6AP=Peripheral Bank 6 Access Parameters */
+		mtdcr ebccfga,r25
+		mtdcr ebccfgd,r4
+		li r25,pb7ap				/* PB7AP=Peripheral Bank 7 Access Parameters */
+		mtdcr ebccfga,r25
+		mtdcr ebccfgd,r4
+
+		li r25,pb2cr				/* PB2CR=Peripheral Bank 2 Configuration Register */
+		mtdcr ebccfga,r25
+
+		lis r4,0x780B
+		ori r4,r4,0xA000
+		mtdcr ebccfgd,r4
+/*
+ * the other areas are only 1MiB in size
+ */
+		lis r4,0x7401
+		ori r4,r4,0xA000
+
+		li r25,pb6cr				/* PB6CR=Peripheral Bank 6 Configuration Register */
+		mtdcr ebccfga,r25
+		lis r4,0x7401
+		ori r4,r4,0xA000
+		mtdcr ebccfgd,r4
+
+		li r25,pb7cr				/* PB7CR=Peripheral Bank 7 Configuration Register */
+		mtdcr ebccfga,r25
+		lis r4,0x7411
+		ori r4,r4,0xA000
+		mtdcr ebccfgd,r4
+
+#ifndef CONFIG_ISP1161_PRESENT
+		li r25,pb4cr				/* PB4CR=Peripheral Bank 4 Configuration Register */
+		mtdcr ebccfga,r25
+		lis r4,0x7421
+		ori r4,r4,0xA000
+		mtdcr ebccfgd,r4
+#endif
+#ifdef IDE_USES_ISA_EMULATION
+		li r25,pb5cr				/* PB5CR=Peripheral Bank 5 Configuration Register */
+		mtdcr ebccfga,r25
+		lis r4,0x0000
+		ori r4,r4,0x0000
+		mtdcr ebccfgd,r4
+#endif
+
+/*-----------------------------------------------------------------------
+ * Memory bank 4: USB controller Philips ISP6111
+ * 0x77C00000 ... 0x77CFFFFF
+ *
+ * The chip is connected to:
+ * - CPU CS#4
+ * - CPU IRQ#2
+ * - CPU DMA 3
+ *
+ * Timing:
+ * - command to first data: 300ns. Software must ensure this timing!
+ * - Write pulse: 26ns
+ * - Read pulse: 33ns
+ * - read cycle time: 150ns
+ * - write cycle time: 140ns
+ *
+ * Note: All calculations are based on 33MHz EBC clock. One '#' or '_' is 30ns
+ *
+ *			  |- 300ns --|
+ *		  |---- 420ns ---|---- 420ns ---| cycle
+ * CS ############:###____#######:###____#######
+ * OE ############:####___#######:####___#######
+ * WE ############:####__########:####__########
+ *
+ * ----> 2 clocks RD/WR pulses: 60ns
+ * ----> CSN: 3 clock, 90ns
+ * ----> OEN: 1 clocks (read cycle)
+ * ----> WBN: 1 clocks (write cycle)
+ * ----> WBE: 2 clocks
+ * ----> TH: 7 clock, 210ns
+ * ----> TWT: 7 clocks
+ *----------------------------------------------------------------------- */
+
+#ifdef CONFIG_ISP1161_PRESENT
+
+		li r4,pb4ap				/* PB4AP=Peripheral Bank 4 Access Parameters */
+		mtdcr ebccfga,r4
+
+		lis r4,0x030D
+		ori r4,r4,0x5E80
+		mtdcr ebccfgd,r4
+
+		li r4,pb4cr				/* PB2CR=Peripheral Bank 4 Configuration Register */
+		mtdcr ebccfga,r4
+
+		lis r4,0x77C1
+		ori r4,r4,0xA000
+		mtdcr ebccfgd,r4
+
+#endif
+
+#ifndef IDE_USES_ISA_EMULATION
+
+/*-----------------------------------------------------------------------
+ * Memory Bank 5 used for IDE access
+ *
+ * Timings for IDE Interface
+ *
+ * SETUP / LENGTH / HOLD - cycles valid for 33.3 MHz clk -> 30ns cycle time
+ *  70		165		30		PIO-Mode 0, [ns]
+ *   3		  6		 1		[Cycles] ----> AP=0x040C0200
+ *  50		125		20	   PIO-Mode 1, [ns]
+ *   2		  5		 1		[Cycles] ----> AP=0x03080200
+ *  30		100		15	   PIO-Mode 2, [ns]
+ *   1		  4		 1		[Cycles] ----> AP=0x02040200
+ *  30		 80		10	   PIO-Mode 3, [ns]
+ *   1		  3		 1		[Cycles] ----> AP=0x01840200
+ *  25		 70		10	   PIO-Mode 4, [ns]
+ *   1		  3		 1		[Cycles] ----> AP=0x01840200
+ *
+ *----------------------------------------------------------------------- */
+
+		li r4,pb5ap
+		mtdcr ebccfga,r4
+		lis r4,0x040C
+		ori r4,r4,0x0200
+		mtdcr ebccfgd,r4
+
+		li r4,pb5cr			/* PB2CR=Peripheral Bank 2 Configuration Register */
+		mtdcr ebccfga,r4
+
+		lis r4,0x7A01
+		ori r4,r4,0xA000
+		mtdcr ebccfgd,r4
+#endif
+/*
+ * External Peripheral Control Register
+ */
+		li r4,epcr
+		mtdcr ebccfga,r4
+
+		lis r4,0xB84E
+		ori r4,r4,0xF000
+		mtdcr ebccfgd,r4
+/*
+ * drive POST code
+ */
+		lis r4,0x7900
+		ori r4,r4,0x0080
+		li r3,0x0001
+		stb r3,0(r4)			/* 01 -> external bus controller is initialized */
+		nop				/* pass2 DCR errata #8 */
+		blr