diff options
author | Tom Rini <trini@konsulko.com> | 2020-04-20 08:45:27 -0400 |
---|---|---|
committer | Tom Rini <trini@konsulko.com> | 2020-04-20 08:45:27 -0400 |
commit | d1bbf833aa7b45c00a42227b9563134643e44237 (patch) | |
tree | ca5a899ee0a4cdf8c4a574d0ac4f1833a27c5f92 /board/tqc | |
parent | 8d5d3bcf3c53d798bd7f3fe7092e994593bcc41c (diff) | |
parent | 931edc6efb11f07557b5fb85f5ce95afa4818f25 (diff) |
Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Diffstat (limited to 'board/tqc')
-rw-r--r-- | board/tqc/tqma6/Kconfig | 15 | ||||
-rw-r--r-- | board/tqc/tqma6/tqma6.c | 12 | ||||
-rw-r--r-- | board/tqc/tqma6/tqma6_mba6.c | 171 |
3 files changed, 32 insertions, 166 deletions
diff --git a/board/tqc/tqma6/Kconfig b/board/tqc/tqma6/Kconfig index 6df4134286..084fdb5230 100644 --- a/board/tqc/tqma6/Kconfig +++ b/board/tqc/tqma6/Kconfig @@ -63,6 +63,17 @@ choice config MBA6 bool "TQMa6 on MBa6 Starterkit" + select DM_ETH + select USB + select DM_USB + select CMD_USB + select USB_STORAGE + select USB_HOST_ETHER + select USB_ETHER_SMSC95XX + select PHYLIB + select PHY_MICREL + select PHY_MICREL_KSZ90X1 + select MXC_UART help Select the MBa6 starterkit. This features a GigE Phy, USB, SD-Card etc. @@ -74,6 +85,10 @@ config WRU4 endchoice +config SYS_TEXT_BASE + default 0x2fc00000 if TQMA6S + default 0x4fc00000 if TQMA6Q || TQMA6DL + config IMX_CONFIG default "board/tqc/tqma6/tqma6q.cfg" if TQMA6Q default "board/tqc/tqma6/tqma6dl.cfg" if TQMA6DL diff --git a/board/tqc/tqma6/tqma6.c b/board/tqc/tqma6/tqma6.c index c8ddc2c1f8..675341abdd 100644 --- a/board/tqc/tqma6/tqma6.c +++ b/board/tqc/tqma6/tqma6.c @@ -60,6 +60,7 @@ int dram_init(void) static const uint16_t tqma6_emmc_dsr = 0x0100; +#ifndef CONFIG_DM_MMC /* eMMC on USDHCI3 always present */ static iomux_v3_cfg_t const tqma6_usdhc3_pads[] = { NEW_PAD_CTRL(MX6_PAD_SD3_CLK__SD3_CLK, USDHC_PAD_CTRL), @@ -132,7 +133,9 @@ int board_mmc_init(bd_t *bis) return 0; } +#endif +#ifndef CONFIG_DM_SPI static iomux_v3_cfg_t const tqma6_ecspi1_pads[] = { /* SS1 */ NEW_PAD_CTRL(MX6_PAD_EIM_D19__GPIO3_IO19, SPI_PAD_CTRL), @@ -164,7 +167,9 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs) (cs == CONFIG_SF_DEFAULT_CS)) ? TQMA6_SF_CS_GPIO : -1; } #endif +#endif +#ifdef CONFIG_SYS_I2C static struct i2c_pads_info tqma6_i2c3_pads = { /* I2C3: on board LM75, M24C64, */ .scl = { @@ -194,6 +199,7 @@ static void tqma6_setup_i2c(void) if (ret) printf("setup I2C3 failed: %d\n", ret); } +#endif int board_early_init_f(void) { @@ -205,8 +211,12 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; +#ifndef CONFIG_DM_SPI tqma6_iomuxc_spi(); +#endif +#ifdef CONFIG_SYS_I2C tqma6_setup_i2c(); +#endif tqma6_bb_board_init(); @@ -235,6 +245,7 @@ static const char *tqma6_get_boardname(void) }; } +#ifdef CONFIG_POWER /* setup board specific PMIC */ int power_init_board(void) { @@ -251,6 +262,7 @@ int power_init_board(void) return 0; } +#endif int board_late_init(void) { diff --git a/board/tqc/tqma6/tqma6_mba6.c b/board/tqc/tqma6/tqma6_mba6.c index 154ea0e925..a5b7587737 100644 --- a/board/tqc/tqma6/tqma6_mba6.c +++ b/board/tqc/tqma6/tqma6_mba6.c @@ -68,13 +68,6 @@ #endif -#define ENET_RX_PAD_CTRL (PAD_CTL_DSE_34ohm) -#define ENET_TX_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_34ohm) -#define ENET_CLK_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_HIGH | \ - PAD_CTL_DSE_34ohm) -#define ENET_MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_60ohm) - /* disable on die termination for RGMII */ #define IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM_DISABLE 0x00000000 /* optimised drive strength for 1.0 .. 1.3 V signal on RGMII */ @@ -82,34 +75,6 @@ /* optimised drive strength for 1.3 .. 2.5 V signal on RGMII */ #define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII_1P5V 0x000C0000 -#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(1, 25) - -static iomux_v3_cfg_t const mba6_enet_pads[] = { - NEW_PAD_CTRL(MX6_PAD_ENET_MDIO__ENET_MDIO, ENET_MDIO_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_ENET_MDC__ENET_MDC, ENET_MDIO_PAD_CTRL), - - NEW_PAD_CTRL(MX6_PAD_RGMII_TXC__RGMII_TXC, ENET_TX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_TD0__RGMII_TD0, ENET_TX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_TD1__RGMII_TD1, ENET_TX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_TD2__RGMII_TD2, ENET_TX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_TD3__RGMII_TD3, ENET_TX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL, - ENET_TX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_ENET_REF_CLK__ENET_TX_CLK, ENET_CLK_PAD_CTRL), - /* - * these pins are also used for config strapping by phy - */ - NEW_PAD_CTRL(MX6_PAD_RGMII_RD0__RGMII_RD0, ENET_RX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_RD1__RGMII_RD1, ENET_RX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_RD2__RGMII_RD2, ENET_RX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_RD3__RGMII_RD3, ENET_RX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_RXC__RGMII_RXC, ENET_RX_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL, - ENET_RX_PAD_CTRL), - /* KSZ9031 PHY Reset */ - NEW_PAD_CTRL(MX6_PAD_ENET_CRS_DV__GPIO1_IO25, GPIO_OUT_PAD_CTRL), -}; - static void mba6_setup_iomuxc_enet(void) { struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; @@ -121,22 +86,6 @@ static void mba6_setup_iomuxc_enet(void) (void *)IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM); __raw_writel(IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII_1P5V, (void *)IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII); - - imx_iomux_v3_setup_multiple_pads(mba6_enet_pads, - ARRAY_SIZE(mba6_enet_pads)); - - /* Reset PHY */ - gpio_direction_output(ENET_PHY_RESET_GPIO , 0); - /* Need delay 10ms after power on according to KSZ9031 spec */ - mdelay(10); - gpio_set_value(ENET_PHY_RESET_GPIO, 1); - /* - * KSZ9031 manual: 100 usec wait time after reset before communication - * over MDIO - * BUGBUG: hardware has an RC const that needs > 10 msec from 0->1 on - * reset before the phy sees a high level - */ - mdelay(15); } static iomux_v3_cfg_t const mba6_uart2_pads[] = { @@ -150,91 +99,14 @@ static void mba6_setup_iomuxc_uart(void) ARRAY_SIZE(mba6_uart2_pads)); } -#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4) -#define USDHC2_WP_GPIO IMX_GPIO_NR(1, 2) - -int tqma6_bb_board_mmc_getcd(struct mmc *mmc) -{ - struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; - int ret = 0; - - if (cfg->esdhc_base == USDHC2_BASE_ADDR) - ret = !gpio_get_value(USDHC2_CD_GPIO); - - return ret; -} - -int tqma6_bb_board_mmc_getwp(struct mmc *mmc) -{ - struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; - int ret = 0; - - if (cfg->esdhc_base == USDHC2_BASE_ADDR) - ret = gpio_get_value(USDHC2_WP_GPIO); - - return ret; -} - -static struct fsl_esdhc_cfg mba6_usdhc_cfg = { - .esdhc_base = USDHC2_BASE_ADDR, - .max_bus_width = 4, -}; - -static iomux_v3_cfg_t const mba6_usdhc2_pads[] = { - NEW_PAD_CTRL(MX6_PAD_SD2_CLK__SD2_CLK, USDHC_CLK_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_SD2_CMD__SD2_CMD, USDHC_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_SD2_DAT0__SD2_DATA0, USDHC_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_SD2_DAT1__SD2_DATA1, USDHC_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_SD2_DAT2__SD2_DATA2, USDHC_PAD_CTRL), - NEW_PAD_CTRL(MX6_PAD_SD2_DAT3__SD2_DATA3, USDHC_PAD_CTRL), - /* CD */ - NEW_PAD_CTRL(MX6_PAD_GPIO_4__GPIO1_IO04, GPIO_IN_PAD_CTRL), - /* WP */ - NEW_PAD_CTRL(MX6_PAD_GPIO_2__GPIO1_IO02, GPIO_IN_PAD_CTRL), -}; - -int tqma6_bb_board_mmc_init(bd_t *bis) -{ - imx_iomux_v3_setup_multiple_pads(mba6_usdhc2_pads, - ARRAY_SIZE(mba6_usdhc2_pads)); - gpio_direction_input(USDHC2_CD_GPIO); - gpio_direction_input(USDHC2_WP_GPIO); - - mba6_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); - if (fsl_esdhc_initialize(bis, &mba6_usdhc_cfg)) - puts("Warning: failed to initialize SD\n"); - - return 0; -} - -static struct i2c_pads_info mba6_i2c1_pads = { -/* I2C1: MBa6x */ - .scl = { - .i2c_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT9__I2C1_SCL, - I2C_PAD_CTRL), - .gpio_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT9__GPIO5_IO27, - I2C_PAD_CTRL), - .gp = IMX_GPIO_NR(5, 27) - }, - .sda = { - .i2c_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT8__I2C1_SDA, - I2C_PAD_CTRL), - .gpio_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT8__GPIO5_IO26, - I2C_PAD_CTRL), - .gp = IMX_GPIO_NR(5, 26) - } -}; - -static void mba6_setup_i2c(void) +int board_mmc_get_env_dev(int devno) { - int ret; /* - * use logical index for bus, e.g. I2C1 -> 0 - * warn on error + * This assumes that the baseboard registered + * the boot device first ... + * Note: SDHC3 == idx2 */ - ret = setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mba6_i2c1_pads); - if (ret) - printf("setup I2C1 failed: %d\n", ret); + return (2 == devno) ? 0 : 1; } int board_phy_config(struct phy_device *phydev) @@ -284,37 +156,6 @@ int board_phy_config(struct phy_device *phydev) return 0; } -int board_eth_init(bd_t *bis) -{ - uint32_t base = IMX_FEC_BASE; - struct mii_dev *bus = NULL; - struct phy_device *phydev = NULL; - int ret; - - bus = fec_get_miibus(base, -1); - if (!bus) - return -EINVAL; - /* scan phy */ - phydev = phy_find_by_mask(bus, (0xf << CONFIG_FEC_MXC_PHYADDR), - PHY_INTERFACE_MODE_RGMII); - - if (!phydev) { - ret = -EINVAL; - goto free_bus; - } - ret = fec_probe(bis, -1, base, bus, phydev); - if (ret) - goto free_phydev; - - return 0; - -free_phydev: - free(phydev); -free_bus: - free(bus); - return ret; -} - int tqma6_bb_board_early_init_f(void) { mba6_setup_iomuxc_uart(); @@ -324,8 +165,6 @@ int tqma6_bb_board_early_init_f(void) int tqma6_bb_board_init(void) { - mba6_setup_i2c(); - /* do it here - to have reset completed */ mba6_setup_iomuxc_enet(); return 0; |