udoo_neo: Add Ethernet support

UDOO Neo boards has one FEC port connected to KSZ8091, add support for it.

Tested on a UDOO Neo Full with "dhcp zImage" command.

Signed-off-by: Breno Lima <breno.lima@nxp.com>

1 files changed, 95 insertions, 0 deletions

diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
index ad7452cd91..688b522ce3 100644
--- a/board/udoo/neo/neo.c
+++ b/board/udoo/neo/neo.c
@@ -10,6 +10,7 @@
  */
 
 #include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/iomux.h>
 #include <asm/arch/mx6-pins.h>
@@ -25,8 +26,11 @@
 #include <linux/sizes.h>
 #include <common.h>
 #include <i2c.h>
+#include <miiphy.h>
+#include <netdev.h>
 #include <power/pmic.h>
 #include <power/pfuze3000_pmic.h>
+#include <malloc.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -50,6 +54,16 @@ enum {
 	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |		\
 	PAD_CTL_ODE)
 
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_SPEED_MED   |                                   \
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL  (PAD_CTL_SPEED_MED | \
+	PAD_CTL_DSE_120ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
+	PAD_CTL_SPEED_MED   | PAD_CTL_SRE_FAST)
+
 #define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED |	\
 	PAD_CTL_DSE_40ohm)
 
@@ -213,6 +227,27 @@ static iomux_v3_cfg_t const usdhc2_pads[] = {
 	MX6_PAD_SD1_CMD__GPIO6_IO_1 | MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_RXC__ENET1_RX_ER | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__GPIO2_IO_9 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_ENET1_CRS__GPIO2_IO_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const phy_control_pads[] = {
+	/* 25MHz Ethernet PHY Clock */
+	MX6_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M |
+	MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+};
+
 static iomux_v3_cfg_t const board_recognition_pads[] = {
 	/*Connected to R184*/
 	MX6_PAD_NAND_READY_B__GPIO4_IO_13 | BOARD_DETECT_PAD_CFG,
@@ -233,6 +268,66 @@ static void setup_iomux_uart(void)
 	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
 }
 
+static int setup_fec(int fec_id)
+{
+	struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
+	int reg;
+
+	imx_iomux_v3_setup_multiple_pads(phy_control_pads,
+					 ARRAY_SIZE(phy_control_pads));
+
+	/* Reset PHY */
+	gpio_direction_output(IMX_GPIO_NR(2, 1) , 0);
+	udelay(10000);
+	gpio_set_value(IMX_GPIO_NR(2, 1), 1);
+	udelay(100);
+
+	reg = readl(&anatop->pll_enet);
+	reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE;
+	writel(reg, &anatop->pll_enet);
+
+	return enable_fec_anatop_clock(fec_id, ENET_25MHZ);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	uint32_t base = IMX_FEC_BASE;
+	struct mii_dev *bus = NULL;
+	struct phy_device *phydev = NULL;
+	int ret;
+
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+	setup_fec(CONFIG_FEC_ENET_DEV);
+
+	bus = fec_get_miibus(base, CONFIG_FEC_ENET_DEV);
+	if (!bus)
+		return -EINVAL;
+
+	phydev = phy_find_by_mask(bus, (0x1 << CONFIG_FEC_MXC_PHYADDR),
+					PHY_INTERFACE_MODE_RMII);
+	if (!phydev) {
+		free(bus);
+		return -EINVAL;
+	}
+
+	ret  = fec_probe(bis, CONFIG_FEC_ENET_DEV, base, bus, phydev);
+	if (ret) {
+		free(bus);
+		free(phydev);
+		return ret;
+	}
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
 int board_init(void)
 {
 	/* Address of boot parameters */