Merge branch 'master' of git://git.denx.de/u-boot-atmel

5 files changed, 231 insertions, 0 deletions

diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
index b807ef9a42..4289179ee6 100644
--- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
@@ -8,6 +8,7 @@
 
 #include <common.h>
 #include <asm/io.h>
+#include <asm/arch/clk.h>
 #include <asm/arch/at91sam9g45_matrix.h>
 #include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
@@ -15,6 +16,7 @@
 #include <asm/arch/gpio.h>
 #include <asm/arch/clk.h>
 #include <lcd.h>
+#include <linux/mtd/nand.h>
 #include <atmel_lcdc.h>
 #include <atmel_mci.h>
 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
@@ -71,6 +73,84 @@ void at91sam9m10g45ek_nand_hw_init(void)
 }
 #endif
 
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+	/*
+	 * On the at91sam9m10g45ek board, the chip wm9711 stays in the
+	 * test mode, so it needs do some action to exit test mode.
+	 */
+	at91_periph_clk_enable(ATMEL_ID_PIODE);
+	at91_set_gpio_output(AT91_PIN_PD7, 0);
+	at91_set_gpio_output(AT91_PIN_PD8, 0);
+	at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
+	at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
+
+#ifdef CONFIG_SYS_USE_MMC
+	at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+	at91sam9m10g45ek_nand_hw_init();
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+	ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+		    ATMEL_MPDDRC_CR_NR_ROW_14 |
+		    ATMEL_MPDDRC_CR_DQMS_SHARED |
+		    ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
+
+	ddr2->rtr = 0x24b;
+
+	ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
+		      2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
+		      2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
+		      8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
+		      2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
+		      1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
+		      1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
+		      2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
+
+	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
+		      200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+		      16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+		      14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+	ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+		      0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+		      7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct atmel_mpddr ddr2;
+	unsigned long csa;
+
+	ddr2_conf(&ddr2);
+
+	/* enable DDR2 clock */
+	writel(0x4, &pmc->scer);
+
+	/* Chip select 1 is for DDR2/SDRAM */
+	csa = readl(&mat->ebicsa);
+	csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+	csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
+	writel(csa, &mat->ebicsa);
+
+	/* DDRAM2 Controller initialize */
+	ddr2_init(ATMEL_BASE_CS6, &ddr2);
+}
+#endif
+
 #ifdef CONFIG_CMD_USB
 static void at91sam9m10g45ek_usb_hw_init(void)
 {
diff --git a/board/atmel/at91sam9n12ek/at91sam9n12ek.c b/board/atmel/at91sam9n12ek/at91sam9n12ek.c
index 9adc9920b4..4f46a03533 100644
--- a/board/atmel/at91sam9n12ek/at91sam9n12ek.c
+++ b/board/atmel/at91sam9n12ek/at91sam9n12ek.c
@@ -257,3 +257,76 @@ int dram_init(void)
 					CONFIG_SYS_SDRAM_SIZE);
 	return 0;
 }
+
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+#ifdef CONFIG_SYS_USE_MMC
+	at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+	at91sam9n12ek_nand_hw_init();
+#elif CONFIG_SYS_USE_SPIFLASH
+	at91_spi0_hw_init(1 << 4);
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+	ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+		    ATMEL_MPDDRC_CR_NR_ROW_13 |
+		    ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
+		    ATMEL_MPDDRC_CR_NB_8BANKS |
+		    ATMEL_MPDDRC_CR_DECOD_INTERLEAVED);
+
+	ddr2->rtr = 0x411;
+
+	ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
+		      8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
+
+	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
+		      200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+		      19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+		      18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+	ddr2->tpr2 = (2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+		      3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+		      7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct atmel_mpddr ddr2;
+	unsigned long csa;
+
+	ddr2_conf(&ddr2);
+
+	/* enable DDR2 clock */
+	writel(0x4, &pmc->scer);
+
+	/* Chip select 1 is for DDR2/SDRAM */
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+	csa &= ~AT91_MATRIX_EBI_DBPU_OFF;
+	csa |= AT91_MATRIX_EBI_DBPD_OFF;
+	csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
+	writel(csa, &matrix->ebicsa);
+
+	/* DDRAM2 Controller initialize */
+	ddr2_init(ATMEL_BASE_CS1, &ddr2);
+}
+#endif
diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
index 17a2a40b4b..114ac5c85a 100644
--- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c
+++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
@@ -293,3 +293,77 @@ int dram_init(void)
 					CONFIG_SYS_SDRAM_SIZE);
 	return 0;
 }
+
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+#ifdef CONFIG_SYS_USE_MMC
+	at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+	at91sam9x5ek_nand_hw_init();
+#elif CONFIG_SYS_USE_SPIFLASH
+	at91_spi0_hw_init(1 << 4);
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+	ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+		    ATMEL_MPDDRC_CR_NR_ROW_13 |
+		    ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
+		    ATMEL_MPDDRC_CR_NB_8BANKS |
+		    ATMEL_MPDDRC_CR_DECOD_INTERLEAVED);
+
+	ddr2->rtr = 0x411;
+
+	ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
+		      8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
+
+	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
+		      200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+		      19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+		      18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+	ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+		      3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+		      7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct atmel_mpddr ddr2;
+	unsigned long csa;
+
+	ddr2_conf(&ddr2);
+
+	/* enable DDR2 clock */
+	writel(0x4, &pmc->scer);
+
+	/* Chip select 1 is for DDR2/SDRAM */
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+	csa &= ~AT91_MATRIX_EBI_DBPU_OFF;
+	csa |= AT91_MATRIX_EBI_DBPD_OFF;
+	csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
+	writel(csa, &matrix->ebicsa);
+
+	/* DDRAM2 Controller initialize */
+	ddr2_init(ATMEL_BASE_CS1, &ddr2);
+}
+#endif
diff --git a/board/atmel/sama5d4_xplained/sama5d4_xplained.c b/board/atmel/sama5d4_xplained/sama5d4_xplained.c
index e7f225a155..7d447fe76b 100644
--- a/board/atmel/sama5d4_xplained/sama5d4_xplained.c
+++ b/board/atmel/sama5d4_xplained/sama5d4_xplained.c
@@ -24,6 +24,7 @@
 #include <netdev.h>
 #include <nand.h>
 #include <spi.h>
+#include <version.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -179,6 +180,7 @@ void lcd_show_board_info(void)
 	int i;
 	char temp[32];
 
+	lcd_printf("%s\n", U_BOOT_VERSION);
 	lcd_printf("2014 ATMEL Corp\n");
 	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
 		   strmhz(temp, get_cpu_clk_rate()));
diff --git a/board/atmel/sama5d4ek/sama5d4ek.c b/board/atmel/sama5d4ek/sama5d4ek.c
index 46e504131c..e9bbb4b1c8 100644
--- a/board/atmel/sama5d4ek/sama5d4ek.c
+++ b/board/atmel/sama5d4ek/sama5d4ek.c
@@ -24,6 +24,7 @@
 #include <netdev.h>
 #include <nand.h>
 #include <spi.h>
+#include <version.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -174,6 +175,7 @@ void lcd_show_board_info(void)
 	int i;
 	char temp[32];
 
+	lcd_printf("%s\n", U_BOOT_VERSION);
 	lcd_printf("2014 ATMEL Corp\n");
 	lcd_printf("at91@atmel.com\n");
 	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),