M28: Add memory detection into SPL

This code allows the DDR DRAM size to be detected at runtime. The RAM size is
stored into two scratch registers, from which it is then fetched in U-Boot.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>

3 files changed, 49 insertions, 3 deletions

diff --git a/board/denx/m28evk/Makefile b/board/denx/m28evk/Makefile
index 47229e6ca9..b6f002fe36 100644
--- a/board/denx/m28evk/Makefile
+++ b/board/denx/m28evk/Makefile
@@ -30,7 +30,7 @@ COBJS	:= m28evk.o
 endif
 
 ifdef	CONFIG_SPL_BUILD
-COBJS	:= mem_init.o mmc_boot.o power_init.o
+COBJS	:= mem_init.o mmc_boot.o power_init.o memsize.o
 endif
 
 SRCS	:= $(COBJS:.o=.c)
@@ -41,6 +41,11 @@ $(LIB):	$(obj).depend $(OBJS)
 
 all:	$(ALL)
 
+ifdef	CONFIG_SPL_BUILD
+memsize.c:
+	ln -sf $(TOPDIR)/common/memsize.c $@
+endif
+
 #########################################################################
 
 # defines $(obj).depend target
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index 118e2222a5..168ceeb6a5 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -63,10 +63,24 @@ int board_init(void)
 	return 0;
 }
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
 int dram_init(void)
 {
-	/* dram_init must store complete ramsize in gd->ram_size */
-	gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		printf("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size!\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
 	return 0;
 }
 
diff --git a/board/denx/m28evk/mem_init.c b/board/denx/m28evk/mem_init.c
index 066fe0d1a4..17d1f9b6a1 100644
--- a/board/denx/m28evk/mem_init.c
+++ b/board/denx/m28evk/mem_init.c
@@ -165,6 +165,31 @@ void mx28_mem_setup_vddd(void)
 		&power_regs->hw_power_vdddctrl);
 }
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+void data_abort_memdetect_handler(void) __attribute__((naked));
+void data_abort_memdetect_handler(void)
+{
+	asm volatile("subs pc, r14, #4");
+}
+
+void mx28_mem_get_size(void)
+{
+	uint32_t sz, da;
+	uint32_t *vt = (uint32_t *)0x20;
+
+	/* Replace the DABT handler. */
+	da = vt[4];
+	vt[4] = (uint32_t)&data_abort_memdetect_handler;
+
+	sz = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+	writel(sz, HW_DIGCTRL_SCRATCH0);
+	writel(sz, HW_DIGCTRL_SCRATCH1);
+
+	/* Restore the old DABT handler. */
+	vt[4] = da;
+}
+
 void mx28_mem_init(void)
 {
 	struct mx28_clkctrl_regs *clkctrl_regs =
@@ -210,4 +235,6 @@ void mx28_mem_init(void)
 	early_delay(10000);
 
 	mx28_mem_setup_cpu_and_hbus();
+
+	mx28_mem_get_size();
 }