Merge branch 'master' of git://www.denx.de/git/u-boot-imx

33 files changed, 2892 insertions, 327 deletions

diff --git a/board/aristainetos/aristainetos.c b/board/aristainetos/aristainetos.c
index e95ec81760..d1e6850636 100644
--- a/board/aristainetos/aristainetos.c
+++ b/board/aristainetos/aristainetos.c
@@ -102,7 +102,7 @@ iomux_v3_cfg_t const usdhc1_pads[] = {
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index a21e7b00e1..566c19b4c9 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -12,6 +12,7 @@
 #include <dm.h>
 #include <fsl_esdhc.h>
 #include <miiphy.h>
+#include <mtd_node.h>
 #include <netdev.h>
 #include <errno.h>
 #include <usb.h>
@@ -28,6 +29,7 @@
 #include <asm/io.h>
 #include <asm/gpio.h>
 #include <dm/platform_data/serial_mxc.h>
+#include <jffs2/load_kernel.h>
 #include "common.h"
 #include "../common/eeprom.h"
 #include "../common/common.h"
@@ -581,6 +583,17 @@ int cm_fx6_setup_ecspi(void) { return 0; }
 
 #ifdef CONFIG_OF_BOARD_SETUP
 #define USDHC3_PATH	"/soc/aips-bus@02100000/usdhc@02198000/"
+
+struct node_info nodes[] = {
+	/*
+	 * Both entries target the same flash chip. The st,m25p compatible
+	 * is used in the vendor device trees, while upstream uses (the
+	 * documented) jedec,spi-nor comptatible.
+	 */
+	{ "st,m25p",	MTD_DEV_TYPE_NOR,	},
+	{ "jedec,spi-nor",	MTD_DEV_TYPE_NOR,	},
+};
+
 int ft_board_setup(void *blob, bd_t *bd)
 {
 	u32 baseboard_rev;
@@ -589,6 +602,8 @@ int ft_board_setup(void *blob, bd_t *bd)
 	char baseboard_name[16];
 	int err;
 
+	fdt_shrink_to_minimum(blob); /* Make room for new properties */
+
 	/* MAC addr */
 	if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
 		fdt_find_and_setprop(blob,
@@ -607,15 +622,16 @@ int ft_board_setup(void *blob, bd_t *bd)
 		return 0; /* Assume not an early revision SB-FX6m baseboard */
 
 	if (!strncmp("SB-FX6m", baseboard_name, 7) && baseboard_rev <= 120) {
-		fdt_shrink_to_minimum(blob); /* Make room for new properties */
 		nodeoffset = fdt_path_offset(blob, USDHC3_PATH);
 		fdt_delprop(blob, nodeoffset, "cd-gpios");
-		fdt_find_and_setprop(blob, USDHC3_PATH, "non-removable",
+		fdt_find_and_setprop(blob, USDHC3_PATH, "broken-cd",
 				     NULL, 0, 1);
 		fdt_find_and_setprop(blob, USDHC3_PATH, "keep-power-in-suspend",
 				     NULL, 0, 1);
 	}
 
+	fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
+
 	return 0;
 }
 #endif
diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
index 225de7c543..3fbd3d2aaa 100644
--- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c
+++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
@@ -678,14 +678,6 @@ int overwrite_console(void)
 	return 1;
 }
 
-static bool is_mx6q(void)
-{
-	if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
-		return true;
-	else
-		return false;
-}
-
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
@@ -703,7 +695,7 @@ int board_init(void)
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
 
-	if (is_mx6q())
+	if (is_mx6dq())
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
 	else
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
@@ -760,7 +752,7 @@ int misc_init_r(void)
 int board_late_init(void)
 {
 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-	if (is_mx6q())
+	if (is_mx6dq())
 		setenv("board_rev", "MX6Q");
 	else
 		setenv("board_rev", "MX6DL");
@@ -1053,7 +1045,7 @@ static void spl_dram_init(int width)
 		return;
 	}
 
-	if (is_mx6q()) {
+	if (is_mx6dq()) {
 		mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
 		mx6_dram_cfg(&sysinfo, &mx6q_mmcd_calib, &mem_ddr_2g);
 	} else if (is_cpu_type(MXC_CPU_MX6SOLO)) {
diff --git a/board/el/el6x/Kconfig b/board/el/el6x/Kconfig
new file mode 100644
index 0000000000..aa9bf25fb4
--- /dev/null
+++ b/board/el/el6x/Kconfig
@@ -0,0 +1,25 @@
+if TARGET_ZC5202
+
+config SYS_BOARD
+	default "el6x"
+
+config SYS_VENDOR
+	default "el"
+
+config SYS_CONFIG_NAME
+	default "zc5202"
+
+endif
+
+if TARGET_ZC5601
+
+config SYS_BOARD
+	default "el6x"
+
+config SYS_VENDOR
+	default "el"
+
+config SYS_CONFIG_NAME
+	default "zc5601"
+
+endif
diff --git a/board/el/el6x/MAINTAINERS b/board/el/el6x/MAINTAINERS
new file mode 100644
index 0000000000..9a40010f50
--- /dev/null
+++ b/board/el/el6x/MAINTAINERS
@@ -0,0 +1,8 @@
+EL6X BOARD
+M:	Stefano Babic <sbabic@denx.de>
+S:	Maintained
+F:	board/el/el6x/
+F:	include/configs/zc5202.h
+F:	include/configs/zc5601.h
+F:	configs/zc5202_defconfig
+F:	configs/zc5601_defconfig
diff --git a/board/el/el6x/Makefile b/board/el/el6x/Makefile
new file mode 100644
index 0000000000..48d5ad9440
--- /dev/null
+++ b/board/el/el6x/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright (C) Stefano Babic <sbabic@denx.de>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := el6x.o
diff --git a/board/el/el6x/el6x.c b/board/el/el6x/el6x.c
new file mode 100644
index 0000000000..3b0fb323bd
--- /dev/null
+++ b/board/el/el6x/el6x.c
@@ -0,0 +1,640 @@
+/*
+ * Copyright (C) Stefano Babic <sbabic@denx.de>
+ *
+ * Based on other i.MX6 boards
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include <asm/arch/mx6-ddr.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define OPEN_PAD_CTRL  (PAD_CTL_ODE  | PAD_CTL_DSE_DISABLE | (0 << 12))
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_PD  (PAD_CTL_PUS_100K_DOWN |		\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_CLK  ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+	PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define I2C_PMIC	1
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+#define ETH_PHY_RESET	IMX_GPIO_NR(2, 4)
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_SD3_DAT5__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_SD3_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+}
+
+#ifdef CONFIG_TARGET_ZC5202
+iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_GPIO_18__ENET_RX_CLK		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD0__ENET_RX_DATA0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD1__ENET_RX_DATA1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_COL2__ENET_RX_DATA2		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_COL0__ENET_RX_DATA3		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_CRS_DV__ENET_RX_EN		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
+	MX6_PAD_ENET_TXD0__ENET_TX_DATA0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TXD1__ENET_TX_DATA1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_GPIO_19__ENET_TX_ER		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_ROW2__ENET_TX_DATA2		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__ENET_TX_DATA3		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TX_EN__ENET_TX_EN		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RX_ER__ENET_RX_ER		| MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	/* Switch Reset */
+	MX6_PAD_NANDF_D4__GPIO2_IO04		| MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	/* Switch Interrupt */
+	MX6_PAD_NANDF_D5__GPIO2_IO05		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* use CRS and COL pads as GPIOs */
+	MX6_PAD_KEY_COL3__GPIO4_IO12		| MUX_PAD_CTRL(OPEN_PAD_CTRL),
+	MX6_PAD_KEY_ROW1__GPIO4_IO09		| MUX_PAD_CTRL(OPEN_PAD_CTRL),
+
+};
+
+#define BOARD_NAME "EL6x-ZC5202"
+#else
+iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
+	MX6_PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_NANDF_D4__GPIO2_IO04		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D5__GPIO2_IO05		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+#define BOARD_NAME "EL6x-ZC5601"
+#endif
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+#ifdef CONFIG_TARGET_ZC5202
+	/* set CRS and COL to input */
+	gpio_direction_input(IMX_GPIO_NR(4, 9));
+	gpio_direction_input(IMX_GPIO_NR(4, 12));
+
+	/* Reset Switch */
+	gpio_direction_output(ETH_PHY_RESET , 0);
+	mdelay(2);
+	gpio_set_value(ETH_PHY_RESET, 1);
+#endif
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+#ifdef CONFIG_MXC_SPI
+#ifdef CONFIG_TARGET_ZC5202
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_DISP0_DAT20__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT21__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT22__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT23__GPIO5_IO17  | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT15__GPIO5_IO09  | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const ecspi3_pads[] = {
+	MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT7__GPIO4_IO28	 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT8__GPIO4_IO29	 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT9__GPIO4_IO30	 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT10__GPIO4_IO31	 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+#endif
+
+iomux_v3_cfg_t const ecspi4_pads[] = {
+	MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D20__GPIO3_IO20  | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
+		? (IMX_GPIO_NR(3, 20)) : -1;
+}
+
+static void setup_spi(void)
+{
+#ifdef CONFIG_TARGET_ZC5202
+	gpio_request(IMX_GPIO_NR(5, 17), "spi_cs0");
+	gpio_request(IMX_GPIO_NR(5, 9), "spi_cs1");
+	gpio_direction_output(IMX_GPIO_NR(5, 17), 1);
+	gpio_direction_output(IMX_GPIO_NR(5, 9), 1);
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+#endif
+
+	gpio_request(IMX_GPIO_NR(3, 20), "spi4_cs0");
+	gpio_direction_output(IMX_GPIO_NR(3, 20), 1);
+	imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
+
+	enable_spi_clk(true, 3);
+}
+#endif
+
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | I2C_PAD,
+		.gp = IMX_GPIO_NR(2, 30)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 5)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | I2C_PAD,
+		.gp = IMX_GPIO_NR(7, 11)
+	}
+};
+
+iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_GPIO_4__SD2_CD_B	| MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = 1; /* eMMC/uSDHC4 is always present */
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+#ifndef CONFIG_SPL_BUILD
+	int ret;
+	int i;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    SD2
+	 * mmc1                    SD3
+	 * mmc2                    eMMC
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_direction_input(USDHC2_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+			       "(%d) then supported by the board (%d)\n",
+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+#else
+	struct src *psrc = (struct src *)SRC_BASE_ADDR;
+	unsigned reg = readl(&psrc->sbmr1) >> 11;
+
+	/*
+	 * Upon reading BOOT_CFG register the following map is done:
+	 * Bit 11 and 12 of BOOT_CFG register can determine the current
+	 * mmc port
+	 * 0x1                  SD1
+	 * 0x2                  SD2
+	 * 0x3                  SD4
+	 */
+
+	switch (reg & 0x3) {
+	case 0x1:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+		usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	case 0x3:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+		usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	}
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+#endif
+
+}
+#endif
+
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+	enable_enet_clk(1);
+
+	return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+
+	setup_iomux_uart();
+	setup_spi();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+
+	return 0;
+}
+
+int power_init_board(void)
+{
+	struct pmic *p;
+	int ret;
+	unsigned int reg;
+
+	ret = power_pfuze100_init(I2C_PMIC);
+	if (ret)
+		return ret;
+
+	p = pmic_get("PFUZE100");
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
+	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
+
+	/* Increase VGEN3 from 2.5 to 2.8V */
+	pmic_reg_read(p, PFUZE100_VGEN3VOL, &reg);
+	reg &= ~LDO_VOL_MASK;
+	reg |= LDOB_2_80V;
+	pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
+
+	/* Increase VGEN5 from 2.8 to 3V */
+	pmic_reg_read(p, PFUZE100_VGEN5VOL, &reg);
+	reg &= ~LDO_VOL_MASK;
+	reg |= LDOB_3_00V;
+	pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
+
+	/* Set SW1AB stanby volage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
+
+	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1ABCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
+
+	/* Set SW1C standby voltage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
+
+	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd2",	 MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	/* 8 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+	setenv("board_name", BOARD_NAME);
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: ");
+	puts(BOARD_NAME "\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#include <libfdt.h>
+
+const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_sdclk_0 =  0x00020030,
+	.dram_sdclk_1 =  0x00020030,
+	.dram_cas =  0x00020030,
+	.dram_ras =  0x00020030,
+	.dram_reset =  0x00020030,
+	.dram_sdcke0 =  0x00003000,
+	.dram_sdcke1 =  0x00003000,
+	.dram_sdba2 =  0x00000000,
+	.dram_sdodt0 =  0x00003030,
+	.dram_sdodt1 =  0x00003030,
+	.dram_sdqs0 =  0x00000030,
+	.dram_sdqs1 =  0x00000030,
+	.dram_sdqs2 =  0x00000030,
+	.dram_sdqs3 =  0x00000030,
+	.dram_sdqs4 =  0x00000030,
+	.dram_sdqs5 =  0x00000030,
+	.dram_sdqs6 =  0x00000030,
+	.dram_sdqs7 =  0x00000030,
+	.dram_dqm0 =  0x00020030,
+	.dram_dqm1 =  0x00020030,
+	.dram_dqm2 =  0x00020030,
+	.dram_dqm3 =  0x00020030,
+	.dram_dqm4 =  0x00020030,
+	.dram_dqm5 =  0x00020030,
+	.dram_dqm6 =  0x00020030,
+	.dram_dqm7 =  0x00020030,
+};
+
+const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_ddr_type =  0x000C0000,
+	.grp_ddrmode_ctl =  0x00020000,
+	.grp_ddrpke =  0x00000000,
+	.grp_addds =  0x00000030,
+	.grp_ctlds =  0x00000030,
+	.grp_ddrmode =  0x00020000,
+	.grp_b0ds =  0x00000030,
+	.grp_b1ds =  0x00000030,
+	.grp_b2ds =  0x00000030,
+	.grp_b3ds =  0x00000030,
+	.grp_b4ds =  0x00000030,
+	.grp_b5ds =  0x00000030,
+	.grp_b6ds =  0x00000030,
+	.grp_b7ds =  0x00000030,
+};
+
+const struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x001F001F,
+	.p0_mpwldectrl1 =  0x001F001F,
+	.p1_mpwldectrl0 =  0x00440044,
+	.p1_mpwldectrl1 =  0x00440044,
+	.p0_mpdgctrl0 =  0x434B0350,
+	.p0_mpdgctrl1 =  0x034C0359,
+	.p1_mpdgctrl0 =  0x434B0350,
+	.p1_mpdgctrl1 =  0x03650348,
+	.p0_mprddlctl =  0x4436383B,
+	.p1_mprddlctl =  0x39393341,
+	.p0_mpwrdlctl =  0x35373933,
+	.p1_mpwrdlctl =  0x48254A36,
+};
+
+/* MT41K128M16JT-125 */
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 1600,
+	.density = 2,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC03, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0x00FFF300, &ccm->CCGR4);
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	/* enable AXI cache for VDOA/VPU/IPU */
+	writel(0xF00000CF, &iomux->gpr[4]);
+	/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+	writel(0x007F007F, &iomux->gpr[6]);
+	writel(0x007F007F, &iomux->gpr[7]);
+}
+
+/*
+ * This section requires the differentiation between iMX6 Sabre boards, but
+ * for now, it will configure only for the mx6q variant.
+ */
+static void spl_dram_init(void)
+{
+	struct mx6_ddr_sysinfo sysinfo = {
+		/* width of data bus:0=16,1=32,2=64 */
+		.dsize = 2,
+		/* config for full 4GB range so that get_mem_size() works */
+		.cs_density = 32, /* 32Gb per CS */
+		/* single chip select */
+		.ncs = 1,
+		.cs1_mirror = 0,
+		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
+		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
+		.walat = 1,	/* Write additional latency */
+		.ralat = 5,	/* Read additional latency */
+		.mif3_mode = 3,	/* Command prediction working mode */
+		.bi_on = 1,	/* Bank interleaving enabled */
+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+		.ddr_type = DDR_TYPE_DDR3,
+	};
+
+	mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+	gpr_init();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+
+#endif
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index d63a979be5..a3ed4cd466 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -64,7 +64,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }
diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c
index 256d6029b4..f978e5044e 100644
--- a/board/freescale/mx6slevk/mx6slevk.c
+++ b/board/freescale/mx6slevk/mx6slevk.c
@@ -61,7 +61,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }
diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
index 886373c901..44e6a7d141 100644
--- a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
+++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
@@ -106,7 +106,7 @@ static int port_exp_direction_output(unsigned gpio, int value)
 
 int dram_init(void)
 {
-	gd->ram_size = PHYS_SDRAM_SIZE;
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 25e009ee9b..8d95c51aaf 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -64,7 +64,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = PHYS_SDRAM_SIZE;
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }
diff --git a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
index 92c92117cd..66d679556b 100644
--- a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
+++ b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
@@ -60,9 +60,6 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define ENET_CLK_PAD_CTRL  (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
 
-#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
-	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
-
 #define IOX_SDI IMX_GPIO_NR(5, 10)
 #define IOX_STCP IMX_GPIO_NR(5, 7)
 #define IOX_SHCP IMX_GPIO_NR(5, 11)
diff --git a/board/freescale/mx7dsabresd/MAINTAINERS b/board/freescale/mx7dsabresd/MAINTAINERS
index b96642a568..c7a22fc0d3 100644
--- a/board/freescale/mx7dsabresd/MAINTAINERS
+++ b/board/freescale/mx7dsabresd/MAINTAINERS
@@ -4,3 +4,4 @@ S:	Maintained
 F:	board/freescale/mx7dsabresd
 F:	include/configs/mx7dsabresd.h
 F:	configs/mx7dsabresd_defconfig
+F:	configs/mx7dsabresd_secure_defconfig
diff --git a/board/gateworks/gw_ventana/common.c b/board/gateworks/gw_ventana/common.c
index 929dde9880..4065c5655a 100644
--- a/board/gateworks/gw_ventana/common.c
+++ b/board/gateworks/gw_ventana/common.c
@@ -132,14 +132,14 @@ void setup_ventana_i2c(void)
 
 /* common to add baseboards */
 static iomux_v3_cfg_t const gw_gpio_pads[] = {
-	/* RS232_EN# */
-	IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
 	/* SD3_VSELECT */
 	IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | DIO_PAD_CFG),
 };
 
 /* prototype */
 static iomux_v3_cfg_t const gwproto_gpio_pads[] = {
+	/* RS232_EN# */
+	IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
 	/* PANLEDG# */
 	IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
 	/* PANLEDR# */
@@ -183,6 +183,8 @@ static iomux_v3_cfg_t const gw51xx_gpio_pads[] = {
 };
 
 static iomux_v3_cfg_t const gw52xx_gpio_pads[] = {
+	/* RS232_EN# */
+	IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
 	/* MSATA_EN */
 	IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG),
 	/* PANLEDG# */
@@ -214,6 +216,8 @@ static iomux_v3_cfg_t const gw52xx_gpio_pads[] = {
 };
 
 static iomux_v3_cfg_t const gw53xx_gpio_pads[] = {
+	/* RS232_EN# */
+	IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
 	/* MSATA_EN */
 	IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG),
 	/* CAN_STBY */
@@ -245,6 +249,8 @@ static iomux_v3_cfg_t const gw53xx_gpio_pads[] = {
 };
 
 static iomux_v3_cfg_t const gw54xx_gpio_pads[] = {
+	/* RS232_EN# */
+	IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
 	/* MSATA_EN */
 	IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG),
 	/* CAN_STBY */
@@ -332,6 +338,219 @@ static iomux_v3_cfg_t const gw553x_gpio_pads[] = {
 	IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
 };
 
+/* Digital I/O */
+struct dio_cfg gw51xx_dio[] = {
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+		IMX_GPIO_NR(1, 16),
+		{ 0, 0 },
+		0
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+		IMX_GPIO_NR(1, 19),
+		{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+		2
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+		IMX_GPIO_NR(1, 17),
+		{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+		3
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) },
+		IMX_GPIO_NR(1, 18),
+		{ IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) },
+		4
+	},
+};
+
+struct dio_cfg gw52xx_dio[] = {
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+		IMX_GPIO_NR(1, 16),
+		{ 0, 0 },
+		0
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+		IMX_GPIO_NR(1, 19),
+		{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+		2
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+		IMX_GPIO_NR(1, 17),
+		{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+		3
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
+		IMX_GPIO_NR(1, 20),
+		{ 0, 0 },
+		0
+	},
+};
+
+struct dio_cfg gw53xx_dio[] = {
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+		IMX_GPIO_NR(1, 16),
+		{ 0, 0 },
+		0
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+		IMX_GPIO_NR(1, 19),
+		{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+		2
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+		IMX_GPIO_NR(1, 17),
+		{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+		3
+	},
+	{
+		{IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
+		IMX_GPIO_NR(1, 20),
+		{ 0, 0 },
+		0
+	},
+};
+
+struct dio_cfg gw54xx_dio[] = {
+	{
+		{ IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09) },
+		IMX_GPIO_NR(1, 9),
+		{ IOMUX_PADS(PAD_GPIO_9__PWM1_OUT) },
+		1
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+		IMX_GPIO_NR(1, 19),
+		{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+		2
+	},
+	{
+		{ IOMUX_PADS(PAD_SD4_DAT1__GPIO2_IO09) },
+		IMX_GPIO_NR(2, 9),
+		{ IOMUX_PADS(PAD_SD4_DAT1__PWM3_OUT) },
+		3
+	},
+	{
+		{ IOMUX_PADS(PAD_SD4_DAT2__GPIO2_IO10) },
+		IMX_GPIO_NR(2, 10),
+		{ IOMUX_PADS(PAD_SD4_DAT2__PWM4_OUT) },
+		4
+	},
+};
+
+struct dio_cfg gw551x_dio[] = {
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+		IMX_GPIO_NR(1, 19),
+		{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+		2
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+		IMX_GPIO_NR(1, 17),
+		{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+		3
+	},
+};
+
+struct dio_cfg gw552x_dio[] = {
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+		IMX_GPIO_NR(1, 16),
+		{ 0, 0 },
+		0
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+		IMX_GPIO_NR(1, 19),
+		{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+		2
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+		IMX_GPIO_NR(1, 17),
+		{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+		3
+	},
+	{
+		{IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
+		IMX_GPIO_NR(1, 20),
+		{ 0, 0 },
+		0
+	},
+	{
+		{IOMUX_PADS(PAD_CSI0_PIXCLK__GPIO5_IO18) },
+		IMX_GPIO_NR(5, 18),
+		{ 0, 0 },
+		0
+	},
+	{
+		{IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20) },
+		IMX_GPIO_NR(5, 20),
+		{ 0, 0 },
+		0
+	},
+	{
+		{IOMUX_PADS(PAD_CSI0_VSYNC__GPIO5_IO21) },
+		IMX_GPIO_NR(5, 21),
+		{ 0, 0 },
+		0
+	},
+	{
+		{IOMUX_PADS(PAD_CSI0_DAT4__GPIO5_IO22) },
+		IMX_GPIO_NR(5, 22),
+		{ 0, 0 },
+		0
+	},
+	{
+		{IOMUX_PADS(PAD_CSI0_DAT5__GPIO5_IO23) },
+		IMX_GPIO_NR(5, 23),
+		{ 0, 0 },
+		0
+	},
+	{
+		{IOMUX_PADS(PAD_CSI0_DAT7__GPIO5_IO25) },
+		IMX_GPIO_NR(5, 25),
+		{ 0, 0 },
+		0
+	},
+};
+
+struct dio_cfg gw553x_dio[] = {
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+		IMX_GPIO_NR(1, 16),
+		{ 0, 0 },
+		0
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+		IMX_GPIO_NR(1, 19),
+		{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+		2
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+		IMX_GPIO_NR(1, 17),
+		{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+		3
+	},
+	{
+		{ IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) },
+		IMX_GPIO_NR(1, 18),
+		{ IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) },
+		4
+	},
+};
 
 /*
  * Board Specific GPIO
@@ -341,33 +560,8 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 	{
 		.gpio_pads = gw54xx_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw54xx_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09) },
-				IMX_GPIO_NR(1, 9),
-				{ IOMUX_PADS(PAD_GPIO_9__PWM1_OUT) },
-				1
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD4_DAT1__GPIO2_IO09) },
-				IMX_GPIO_NR(2, 9),
-				{ IOMUX_PADS(PAD_SD4_DAT1__PWM3_OUT) },
-				3
-			},
-			{
-				{ IOMUX_PADS(PAD_SD4_DAT2__GPIO2_IO10) },
-				IMX_GPIO_NR(2, 10),
-				{ IOMUX_PADS(PAD_SD4_DAT2__PWM4_OUT) },
-				4
-			},
-		},
-		.num_gpios = 4,
+		.dio_cfg = gw54xx_dio,
+		.dio_num = ARRAY_SIZE(gw54xx_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 6),
 			IMX_GPIO_NR(4, 10),
@@ -385,33 +579,8 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 	{
 		.gpio_pads = gw51xx_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw51xx_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
-				IMX_GPIO_NR(1, 16),
-				{ 0, 0 },
-				0
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
-				IMX_GPIO_NR(1, 17),
-				{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
-				3
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) },
-				IMX_GPIO_NR(1, 18),
-				{ IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) },
-				4
-			},
-		},
-		.num_gpios = 4,
+		.dio_cfg = gw51xx_dio,
+		.dio_num = ARRAY_SIZE(gw51xx_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 6),
 			IMX_GPIO_NR(4, 10),
@@ -428,33 +597,8 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 	{
 		.gpio_pads = gw52xx_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw52xx_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
-				IMX_GPIO_NR(1, 16),
-				{ 0, 0 },
-				0
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
-				IMX_GPIO_NR(1, 17),
-				{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
-				3
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
-				IMX_GPIO_NR(1, 20),
-				{ 0, 0 },
-				0
-			},
-		},
-		.num_gpios = 4,
+		.dio_cfg = gw52xx_dio,
+		.dio_num = ARRAY_SIZE(gw52xx_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 6),
 			IMX_GPIO_NR(4, 7),
@@ -468,39 +612,15 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 		.usb_sel = IMX_GPIO_NR(1, 2),
 		.wdis = IMX_GPIO_NR(7, 12),
 		.msata_en = GP_MSATA_SEL,
+		.rs232_en = GP_RS232_EN,
 	},
 
 	/* GW53xx */
 	{
 		.gpio_pads = gw53xx_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw53xx_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
-				IMX_GPIO_NR(1, 16),
-				{ 0, 0 },
-				0
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
-				IMX_GPIO_NR(1, 17),
-				{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
-				3
-			},
-			{
-				{IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
-				IMX_GPIO_NR(1, 20),
-				{ 0, 0 },
-				0
-			},
-		},
-		.num_gpios = 4,
+		.dio_cfg = gw53xx_dio,
+		.dio_num = ARRAY_SIZE(gw53xx_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 6),
 			IMX_GPIO_NR(4, 7),
@@ -513,39 +633,15 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 		.vidin_en = IMX_GPIO_NR(3, 31),
 		.wdis = IMX_GPIO_NR(7, 12),
 		.msata_en = GP_MSATA_SEL,
+		.rs232_en = GP_RS232_EN,
 	},
 
 	/* GW54xx */
 	{
 		.gpio_pads = gw54xx_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw54xx_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09) },
-				IMX_GPIO_NR(1, 9),
-				{ IOMUX_PADS(PAD_GPIO_9__PWM1_OUT) },
-				1
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD4_DAT1__GPIO2_IO09) },
-				IMX_GPIO_NR(2, 9),
-				{ IOMUX_PADS(PAD_SD4_DAT1__PWM3_OUT) },
-				3
-			},
-			{
-				{ IOMUX_PADS(PAD_SD4_DAT2__GPIO2_IO10) },
-				IMX_GPIO_NR(2, 10),
-				{ IOMUX_PADS(PAD_SD4_DAT2__PWM4_OUT) },
-				4
-			},
-		},
-		.num_gpios = 4,
+		.dio_cfg = gw54xx_dio,
+		.dio_num = ARRAY_SIZE(gw54xx_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 6),
 			IMX_GPIO_NR(4, 7),
@@ -560,27 +656,15 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 		.pcie_sson = IMX_GPIO_NR(1, 20),
 		.wdis = IMX_GPIO_NR(5, 17),
 		.msata_en = GP_MSATA_SEL,
+		.rs232_en = GP_RS232_EN,
 	},
 
 	/* GW551x */
 	{
 		.gpio_pads = gw551x_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw551x_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
-				IMX_GPIO_NR(1, 17),
-				{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
-				3
-			},
-		},
-		.num_gpios = 2,
+		.dio_cfg = gw551x_dio,
+		.dio_num = ARRAY_SIZE(gw551x_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 7),
 		},
@@ -592,33 +676,8 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 	{
 		.gpio_pads = gw552x_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw552x_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
-				IMX_GPIO_NR(1, 16),
-				{ 0, 0 },
-				0
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
-				IMX_GPIO_NR(1, 17),
-				{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
-				3
-			},
-			{
-				{IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
-				IMX_GPIO_NR(1, 20),
-				{ 0, 0 },
-				0
-			},
-		},
-		.num_gpios = 4,
+		.dio_cfg = gw552x_dio,
+		.dio_num = ARRAY_SIZE(gw552x_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 6),
 			IMX_GPIO_NR(4, 7),
@@ -634,33 +693,8 @@ struct ventana gpio_cfg[GW_UNKNOWN] = {
 	{
 		.gpio_pads = gw553x_gpio_pads,
 		.num_pads = ARRAY_SIZE(gw553x_gpio_pads)/2,
-		.dio_cfg = {
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
-				IMX_GPIO_NR(1, 16),
-				{ 0, 0 },
-				0
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
-				IMX_GPIO_NR(1, 19),
-				{ IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
-				2
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
-				IMX_GPIO_NR(1, 17),
-				{ IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
-				3
-			},
-			{
-				{ IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) },
-				IMX_GPIO_NR(1, 18),
-				{ IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) },
-				4
-			},
-		},
-		.num_gpios = 4,
+		.dio_cfg = gw553x_dio,
+		.dio_num = ARRAY_SIZE(gw553x_dio),
 		.leds = {
 			IMX_GPIO_NR(4, 10),
 			IMX_GPIO_NR(4, 11),
@@ -682,10 +716,6 @@ void setup_iomux_gpio(int board, struct ventana_board_info *info)
 	gpio_request(GP_USB_OTG_PWR, "usbotg_pwr");
 	gpio_direction_output(GP_USB_OTG_PWR, 0);
 
-	/* RS232_EN# */
-	gpio_request(GP_RS232_EN, "rs232_en");
-	gpio_direction_output(GP_RS232_EN, 0);
-
 	if (board >= GW_UNKNOWN)
 		return;
 
@@ -693,6 +723,12 @@ void setup_iomux_gpio(int board, struct ventana_board_info *info)
 	imx_iomux_v3_setup_multiple_pads(gpio_cfg[board].gpio_pads,
 					 gpio_cfg[board].num_pads);
 
+	/* RS232_EN# */
+	if (gpio_cfg[board].rs232_en) {
+		gpio_request(gpio_cfg[board].rs232_en, "rs232_en");
+		gpio_direction_output(gpio_cfg[board].rs232_en, 0);
+	}
+
 	/* GW522x Uses GPIO3_IO23 for PCIE_RST# */
 	if (board == GW52xx && info->model[4] == '2')
 		gpio_cfg[board].pcie_rst = IMX_GPIO_NR(3, 23);
@@ -788,7 +824,10 @@ void setup_board_gpio(int board, struct ventana_board_info *info)
 		return;
 
 	/* RS232_EN# */
-	gpio_direction_output(GP_RS232_EN, (hwconfig("rs232")) ? 0 : 1);
+	if (gpio_cfg[board].rs232_en) {
+		gpio_direction_output(gpio_cfg[board].rs232_en,
+				      (hwconfig("rs232")) ? 0 : 1);
+	}
 
 	/* MSATA Enable */
 	if (gpio_cfg[board].msata_en && is_cpu_type(MXC_CPU_MX6Q)) {
@@ -806,7 +845,7 @@ void setup_board_gpio(int board, struct ventana_board_info *info)
 	 * Configure DIO pinmux/padctl registers
 	 * see IMX6DQRM/IMX6SDLRM IOMUXC_SW_PAD_CTL_PAD_* register definitions
 	 */
-	for (i = 0; i < gpio_cfg[board].num_gpios; i++) {
+	for (i = 0; i < gpio_cfg[board].dio_num; i++) {
 		struct dio_cfg *cfg = &gpio_cfg[board].dio_cfg[i];
 		iomux_v3_cfg_t ctrl = DIO_PAD_CFG;
 		unsigned cputype = is_cpu_type(MXC_CPU_MX6Q) ? 0 : 1;
@@ -851,8 +890,10 @@ void setup_board_gpio(int board, struct ventana_board_info *info)
 			printf("MSATA: %s\n", (hwconfig("msata") ?
 			       "enabled" : "disabled"));
 		}
-		printf("RS232: %s\n", (hwconfig("rs232")) ?
-		       "enabled" : "disabled");
+		if (gpio_cfg[board].rs232_en) {
+			printf("RS232: %s\n", (hwconfig("rs232")) ?
+			       "enabled" : "disabled");
+		}
 	}
 }
 
diff --git a/board/gateworks/gw_ventana/common.h b/board/gateworks/gw_ventana/common.h
index d037767ecc..3d7aff1077 100644
--- a/board/gateworks/gw_ventana/common.h
+++ b/board/gateworks/gw_ventana/common.h
@@ -48,8 +48,8 @@
 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 
 /*
- * each baseboard has 4 user configurable Digital IO lines which can
- * be pinmuxed as a GPIO or in some cases a PWM
+ * each baseboard has an optional set user configurable Digital IO lines which
+ * can be pinmuxed as a GPIO or in some cases a PWM
  */
 struct dio_cfg {
 	iomux_v3_cfg_t gpio_padmux[2];
@@ -63,8 +63,8 @@ struct ventana {
 	iomux_v3_cfg_t const *gpio_pads;
 	int num_pads;
 	/* DIO pinmux/val */
-	struct dio_cfg dio_cfg[4];
-	int num_gpios;
+	struct dio_cfg *dio_cfg;
+	int dio_num;
 	/* various gpios (0 if non-existent) */
 	int leds[3];
 	int pcie_rst;
@@ -78,6 +78,8 @@ struct ventana {
 	int usb_sel;
 	int wdis;
 	int msata_en;
+	int rs232_en;
+	/* various features */
 	bool usd_vsel;
 };
 
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index 70395ac91d..5d871ceed9 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -491,14 +491,54 @@ int imx6_pcie_toggle_reset(void)
  * GPIO's as PERST# signals for its downstream ports - configure the GPIO's
  * properly and assert reset for 100ms.
  */
+#define MAX_PCI_DEVS	32
+struct pci_dev {
+	pci_dev_t devfn;
+	unsigned short vendor;
+	unsigned short device;
+	unsigned short class;
+	unsigned short busno; /* subbordinate busno */
+	struct pci_dev *ppar;
+};
+struct pci_dev pci_devs[MAX_PCI_DEVS];
+int pci_devno;
+int pci_bridgeno;
+
 void board_pci_fixup_dev(struct pci_controller *hose, pci_dev_t dev,
 			 unsigned short vendor, unsigned short device,
 			 unsigned short class)
 {
+	int i;
 	u32 dw;
+	struct pci_dev *pdev = &pci_devs[pci_devno++];
 
 	debug("%s: %02d:%02d.%02d: %04x:%04x\n", __func__,
 	      PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev), vendor, device);
+
+	/* store array of devs for later use in device-tree fixup */
+	pdev->devfn = dev;
+	pdev->vendor = vendor;
+	pdev->device = device;
+	pdev->class = class;
+	pdev->ppar = NULL;
+	if (class == PCI_CLASS_BRIDGE_PCI)
+		pdev->busno = ++pci_bridgeno;
+	else
+		pdev->busno = 0;
+
+	/* fixup RC - it should be 00:00.0 not 00:01.0 */
+	if (PCI_BUS(dev) == 0)
+		pdev->devfn = 0;
+
+	/* find dev's parent */
+	for (i = 0; i < pci_devno; i++) {
+		if (pci_devs[i].busno == PCI_BUS(pdev->devfn)) {
+			pdev->ppar = &pci_devs[i];
+			break;
+		}
+	}
+
+	/* assert downstream PERST# */
 	if (vendor == PCI_VENDOR_ID_PLX &&
 	    (device & 0xfff0) == 0x8600 &&
 	    PCI_DEV(dev) == 0 && PCI_FUNC(dev) == 0) {
@@ -660,13 +700,14 @@ static const struct boot_mode board_boot_modes[] = {
 int misc_init_r(void)
 {
 	struct ventana_board_info *info = &ventana_info;
+	char buf[256];
+	int i;
 
 	/* set env vars based on EEPROM data */
 	if (ventana_info.model[0]) {
 		char str[16], fdt[36];
 		char *p;
 		const char *cputype = "";
-		int i;
 
 		/*
 		 * FDT name will be prefixed with CPU type.  Three versions
@@ -729,6 +770,19 @@ int misc_init_r(void)
 		setenv("mem_mb", str);
 	}
 
+	/* Set a non-initialized hwconfig based on board configuration */
+	if (!strcmp(getenv("hwconfig"), "_UNKNOWN_")) {
+		sprintf(buf, "hwconfig=");
+		if (gpio_cfg[board_type].rs232_en)
+			strcat(buf, "rs232;");
+		for (i = 0; i < gpio_cfg[board_type].dio_num; i++) {
+			char buf1[32];
+			sprintf(buf1, "dio%d:mode=gpio;", i);
+			if (strlen(buf) + strlen(buf1) < sizeof(buf))
+				strcat(buf, buf1);
+		}
+		setenv("hwconfig", buf);
+	}
 
 	/* setup baseboard specific GPIO based on board and env */
 	setup_board_gpio(board_type, info);
@@ -802,6 +856,224 @@ static inline void ft_delprop_path(void *blob, const char *path,
 	}
 }
 
+#if defined(CONFIG_CMD_PCI)
+#define PCI_ID(x) ( \
+	(PCI_BUS(x->devfn)<<16)| \
+	(PCI_DEV(x->devfn)<<11)| \
+	(PCI_FUNC(x->devfn)<<8) \
+	)
+#define PCIE_PATH	"/soc/pcie@0x01000000"
+int fdt_add_pci_node(void *blob, int par, struct pci_dev *dev)
+{
+	uint32_t reg[5];
+	char node[32];
+	int np;
+
+	sprintf(node, "pcie@%d,%d,%d", PCI_BUS(dev->devfn),
+		PCI_DEV(dev->devfn), PCI_FUNC(dev->devfn));
+
+	np = fdt_subnode_offset(blob, par, node);
+	if (np >= 0)
+		return np;
+	np = fdt_add_subnode(blob, par, node);
+	if (np < 0) {
+		printf("   %s failed: no space\n", __func__);
+		return np;
+	}
+
+	memset(reg, 0, sizeof(reg));
+	reg[0] = cpu_to_fdt32(PCI_ID(dev));
+	fdt_setprop(blob, np, "reg", reg, sizeof(reg));
+
+	return np;
+}
+
+/* build a path of nested PCI devs for all bridges passed through */
+int fdt_add_pci_path(void *blob, struct pci_dev *dev)
+{
+	struct pci_dev *bridges[MAX_PCI_DEVS];
+	int k, np;
+
+	/* build list of parents */
+	np = fdt_path_offset(blob, PCIE_PATH);
+	if (np < 0)
+		return np;
+
+	k = 0;
+	while (dev) {
+		bridges[k++] = dev;
+		dev = dev->ppar;
+	};
+
+	/* now add them the to DT in reverse order */
+	while (k--) {
+		np = fdt_add_pci_node(blob, np, bridges[k]);
+		if (np < 0)
+			break;
+	}
+
+	return np;
+}
+
+/*
+ * The GW16082 has a hardware errata errata such that it's
+ * INTA/B/C/D are mis-mapped to its four slots (slot12-15). Because
+ * of this normal PCI interrupt swizzling will not work so we will
+ * provide an irq-map via device-tree.
+ */
+int fdt_fixup_gw16082(void *blob, int np, struct pci_dev *dev)
+{
+	int len;
+	int host;
+	uint32_t imap_new[8*4*4];
+	const uint32_t *imap;
+	uint32_t irq[4];
+	uint32_t reg[4];
+	int i;
+
+	/* build irq-map based on host controllers map */
+	host = fdt_path_offset(blob, PCIE_PATH);
+	if (host < 0) {
+		printf("   %s failed: missing host\n", __func__);
+		return host;
+	}
+
+	/* use interrupt data from root complex's node */
+	imap = fdt_getprop(blob, host, "interrupt-map", &len);
+	if (!imap || len != 128) {
+		printf("   %s failed: invalid interrupt-map\n",
+		       __func__);
+		return -FDT_ERR_NOTFOUND;
+	}
+
+	/* obtain irq's of host controller in pin order */
+	for (i = 0; i < 4; i++)
+		irq[(fdt32_to_cpu(imap[(i*8)+3])-1)%4] = imap[(i*8)+6];
+
+	/*
+	 * determine number of swizzles necessary:
+	 *   For each bridge we pass through we need to swizzle
+	 *   the number of the slot we are on.
+	 */
+	struct pci_dev *d;
+	int b;
+	b = 0;
+	d = dev->ppar;
+	while(d && d->ppar) {
+		b += PCI_DEV(d->devfn);
+		d = d->ppar;
+	}
+
+	/* create new irq mappings for slots12-15
+	 * <skt> <idsel> <slot> <skt-inta> <skt-intb>
+	 * J3    AD28    12     INTD      INTA
+	 * J4    AD29    13     INTC      INTD
+	 * J5    AD30    14     INTB      INTC
+	 * J2    AD31    15     INTA      INTB
+	 */
+	for (i = 0; i < 4; i++) {
+		/* addr matches bus:dev:func */
+		u32 addr = dev->busno << 16 | (12+i) << 11;
+
+		/* default cells from root complex */
+		memcpy(&imap_new[i*32], imap, 128);
+		/* first cell is PCI device address (BDF) */
+		imap_new[(i*32)+(0*8)+0] = cpu_to_fdt32(addr);
+		imap_new[(i*32)+(1*8)+0] = cpu_to_fdt32(addr);
+		imap_new[(i*32)+(2*8)+0] = cpu_to_fdt32(addr);
+		imap_new[(i*32)+(3*8)+0] = cpu_to_fdt32(addr);
+		/* third cell is pin */
+		imap_new[(i*32)+(0*8)+3] = cpu_to_fdt32(1);
+		imap_new[(i*32)+(1*8)+3] = cpu_to_fdt32(2);
+		imap_new[(i*32)+(2*8)+3] = cpu_to_fdt32(3);
+		imap_new[(i*32)+(3*8)+3] = cpu_to_fdt32(4);
+		/* sixth cell is relative interrupt */
+		imap_new[(i*32)+(0*8)+6] = irq[(15-(12+i)+b+0)%4];
+		imap_new[(i*32)+(1*8)+6] = irq[(15-(12+i)+b+1)%4];
+		imap_new[(i*32)+(2*8)+6] = irq[(15-(12+i)+b+2)%4];
+		imap_new[(i*32)+(3*8)+6] = irq[(15-(12+i)+b+3)%4];
+	}
+	fdt_setprop(blob, np, "interrupt-map", imap_new,
+		    sizeof(imap_new));
+	reg[0] = cpu_to_fdt32(0xfff00);
+	reg[1] = 0;
+	reg[2] = 0;
+	reg[3] = cpu_to_fdt32(0x7);
+	fdt_setprop(blob, np, "interrupt-map-mask", reg, sizeof(reg));
+	fdt_setprop_cell(blob, np, "#interrupt-cells", 1);
+	fdt_setprop_string(blob, np, "device_type", "pci");
+	fdt_setprop_cell(blob, np, "#address-cells", 3);
+	fdt_setprop_cell(blob, np, "#size-cells", 2);
+	printf("   Added custom interrupt-map for GW16082\n");
+
+	return 0;
+}
+
+/* The sky2 GigE MAC obtains it's MAC addr from device-tree by default */
+int fdt_fixup_sky2(void *blob, int np, struct pci_dev *dev)
+{
+	char *tmp, *end;
+	char mac[16];
+	unsigned char mac_addr[6];
+	int j;
+
+	sprintf(mac, "eth1addr");
+	tmp = getenv(mac);
+	if (tmp) {
+		for (j = 0; j < 6; j++) {
+			mac_addr[j] = tmp ?
+				      simple_strtoul(tmp, &end,16) : 0;
+			if (tmp)
+				tmp = (*end) ? end+1 : end;
+		}
+		fdt_setprop(blob, np, "local-mac-address", mac_addr,
+			    sizeof(mac_addr));
+		printf("   Added mac addr for eth1\n");
+		return 0;
+	}
+
+	return -1;
+}
+
+/*
+ * PCI DT nodes must be nested therefore if we need to apply a DT fixup
+ * we will walk the PCI bus and add bridge nodes up to the device receiving
+ * the fixup.
+ */
+void ft_board_pci_fixup(void *blob, bd_t *bd)
+{
+	int i, np;
+	struct pci_dev *dev;
+
+	for (i = 0; i < pci_devno; i++) {
+		dev = &pci_devs[i];
+
+		/*
+		 * The GW16082 consists of a TI XIO2001 PCIe-to-PCI bridge and
+		 * an EEPROM at i2c1-0x50.
+		 */
+		if ((dev->vendor == PCI_VENDOR_ID_TI) &&
+		    (dev->device == 0x8240) &&
+		    (i2c_set_bus_num(1) == 0) &&
+		    (i2c_probe(0x50) == 0))
+		{
+			np = fdt_add_pci_path(blob, dev);
+			if (np > 0)
+				fdt_fixup_gw16082(blob, np, dev);
+		}
+
+		/* ethernet1 mac address */
+		else if ((dev->vendor == PCI_VENDOR_ID_MARVELL) &&
+		         (dev->device == 0x4380))
+		{
+			np = fdt_add_pci_path(blob, dev);
+			if (np > 0)
+				fdt_fixup_sky2(blob, np, dev);
+		}
+	}
+}
+#endif /* if defined(CONFIG_CMD_PCI) */
+
 /*
  * called prior to booting kernel or by 'fdt boardsetup' command
  *
@@ -811,6 +1083,10 @@ static inline void ft_delprop_path(void *blob, const char *path,
  *  - board (full model from EEPROM)
  *  - peripherals removed from DTB if not loaded on board (per EEPROM config)
  */
+#define UART1_PATH	"/soc/aips-bus@02100000/serial@021ec000"
+#define WDOG1_PATH	"/soc/aips-bus@02000000/wdog@020bc000"
+#define WDOG2_PATH	"/soc/aips-bus@02000000/wdog@020c0000"
+#define GPIO3_PATH	"/soc/aips-bus@02000000/gpio@020a4000"
 int ft_board_setup(void *blob, bd_t *bd)
 {
 	struct ventana_board_info *info = &ventana_info;
@@ -864,94 +1140,140 @@ int ft_board_setup(void *blob, bd_t *bd)
 	ft_sethdmiinfmt(blob, getenv("hdmiinfmt"));
 
 	/*
-	 * disable serial2 node for GW54xx for compatibility with older
-	 * 3.10.x kernel that improperly had this node enabled in the DT
+	 * Board model specific fixups
 	 */
-	if (board_type == GW54xx) {
-		i = fdt_path_offset(blob,
-				    "/soc/aips-bus@02100000/serial@021ec000");
-		if (i)
-			fdt_del_node(blob, i);
-	}
-
-	/*
-	 * disable wdog1/wdog2 nodes for GW51xx below revC to work around
-	 * errata causing wdog timer to be unreliable.
-	 */
-	if (board_type == GW51xx && rev >= 'A' && rev < 'C') {
-		i = fdt_path_offset(blob,
-				    "/soc/aips-bus@02000000/wdog@020bc000");
-		if (i)
-			fdt_status_disabled(blob, i);
-	}
+	switch (board_type) {
+	case GW51xx:
+		/*
+		 * disable wdog node for GW51xx-A/B to work around
+		 * errata causing wdog timer to be unreliable.
+		 */
+		if (rev >= 'A' && rev < 'C') {
+			i = fdt_path_offset(blob, WDOG1_PATH);
+			if (i)
+				fdt_status_disabled(blob, i);
+		}
 
-	/* GW522x Uses GPIO3_IO23 instead of GPIO1_IO29 */
-	else if (board_type == GW52xx && info->model[4] == '2') {
-		u32 handle = 0;
-		u32 *range = NULL;
+		/* GW51xx-E adds WDOG1_B external reset */
+		if (rev < 'E')
+			ft_delprop_path(blob, WDOG1_PATH,
+					"fsl,ext-reset-output");
+		break;
 
-		i = fdt_node_offset_by_compatible(blob, -1, "fsl,imx6q-pcie");
-		if (i)
-			range = (u32 *)fdt_getprop(blob, i, "reset-gpio",
-						   NULL);
+	case GW52xx:
+		/* GW522x Uses GPIO3_IO23 instead of GPIO1_IO29 */
+		if (info->model[4] == '2') {
+			u32 handle = 0;
+			u32 *range = NULL;
 
-		if (range) {
-			i = fdt_path_offset(blob,
-					    "/soc/aips-bus@02000000/gpio@020a4000");
+			i = fdt_node_offset_by_compatible(blob, -1,
+							  "fsl,imx6q-pcie");
 			if (i)
-				handle = fdt_get_phandle(blob, i);
-			if (handle) {
-				range[0] = cpu_to_fdt32(handle);
-				range[1] = cpu_to_fdt32(23);
+				range = (u32 *)fdt_getprop(blob, i,
+							   "reset-gpio", NULL);
+
+			if (range) {
+				i = fdt_path_offset(blob, GPIO3_PATH);
+				if (i)
+					handle = fdt_get_phandle(blob, i);
+				if (handle) {
+					range[0] = cpu_to_fdt32(handle);
+					range[1] = cpu_to_fdt32(23);
+				}
 			}
-		}
 
-		/* these have broken usd_vsel */
-		if (strstr((const char *)info->model, "SP318-B") ||
-		    strstr((const char *)info->model, "SP331-B"))
-			gpio_cfg[board_type].usd_vsel = 0;
-	}
+			/* these have broken usd_vsel */
+			if (strstr((const char *)info->model, "SP318-B") ||
+			    strstr((const char *)info->model, "SP331-B"))
+				gpio_cfg[board_type].usd_vsel = 0;
 
-	/*
-	 * isolate CSI0_DATA_EN for GW551x below revB to work around
-	 * errata causing non functional digital video in (it is not hooked up)
-	 */
-	else if (board_type == GW551x && rev == 'A') {
-		u32 *range = NULL;
-		int len;
-		const u32 *handle = NULL;
+			/* GW520x-E adds WDOG1_B external reset */
+			if (info->model[4] == '0' && rev < 'E')
+				ft_delprop_path(blob, WDOG1_PATH,
+						"fsl,ext-reset-output");
 
-		i = fdt_node_offset_by_compatible(blob, -1,
-						  "fsl,imx-tda1997x-video");
-		if (i)
-			handle = fdt_getprop(blob, i, "pinctrl-0", NULL);
-		if (handle)
-			i = fdt_node_offset_by_phandle(blob,
-						       fdt32_to_cpu(*handle));
+			/* GW522x-B adds WDOG1_B external reset */
+			if (info->model[4] == '2' && rev < 'B')
+				ft_delprop_path(blob, WDOG1_PATH,
+						"fsl,ext-reset-output");
+		}
+		break;
+
+	case GW53xx:
+		/* GW53xx-E adds WDOG1_B external reset */
+		if (rev < 'E')
+			ft_delprop_path(blob, WDOG1_PATH,
+					"fsl,ext-reset-output");
+		break;
+
+	case GW54xx:
+		/*
+		 * disable serial2 node for GW54xx for compatibility with older
+		 * 3.10.x kernel that improperly had this node enabled in the DT
+		 */
+		i = fdt_path_offset(blob, UART1_PATH);
 		if (i)
-			range = (u32 *)fdt_getprop(blob, i, "fsl,pins", &len);
-		if (range) {
-			len /= sizeof(u32);
-			for (i = 0; i < len; i += 6) {
-				u32 mux_reg = fdt32_to_cpu(range[i+0]);
-				u32 conf_reg = fdt32_to_cpu(range[i+1]);
-				/* mux PAD_CSI0_DATA_EN to GPIO */
-				if (is_cpu_type(MXC_CPU_MX6Q) &&
-				    mux_reg == 0x260 && conf_reg == 0x630)
-					range[i+3] = cpu_to_fdt32(0x5);
-				else if (!is_cpu_type(MXC_CPU_MX6Q) &&
-				    mux_reg == 0x08c && conf_reg == 0x3a0)
-					range[i+3] = cpu_to_fdt32(0x5);
+			fdt_del_node(blob, i);
+
+		/* GW54xx-E adds WDOG2_B external reset */
+		if (rev < 'E')
+			ft_delprop_path(blob, WDOG2_PATH,
+					"fsl,ext-reset-output");
+		break;
+
+	case GW551x:
+		/*
+		 * isolate CSI0_DATA_EN for GW551x-A to work around errata
+		 * causing non functional digital video in (it is not hooked up)
+		 */
+		if (rev == 'A') {
+			u32 *range = NULL;
+			int len;
+			const u32 *handle = NULL;
+
+			i = fdt_node_offset_by_compatible(blob, -1,
+						"fsl,imx-tda1997x-video");
+			if (i)
+				handle = fdt_getprop(blob, i, "pinctrl-0",
+						     NULL);
+			if (handle)
+				i = fdt_node_offset_by_phandle(blob,
+							fdt32_to_cpu(*handle));
+			if (i)
+				range = (u32 *)fdt_getprop(blob, i, "fsl,pins",
+							   &len);
+			if (range) {
+				len /= sizeof(u32);
+				for (i = 0; i < len; i += 6) {
+					u32 mux_reg = fdt32_to_cpu(range[i+0]);
+					u32 conf_reg = fdt32_to_cpu(range[i+1]);
+					/* mux PAD_CSI0_DATA_EN to GPIO */
+					if (is_cpu_type(MXC_CPU_MX6Q) &&
+					    mux_reg == 0x260 &&
+					    conf_reg == 0x630)
+						range[i+3] = cpu_to_fdt32(0x5);
+					else if (!is_cpu_type(MXC_CPU_MX6Q) &&
+						 mux_reg == 0x08c &&
+						 conf_reg == 0x3a0)
+						range[i+3] = cpu_to_fdt32(0x5);
+				}
+				fdt_setprop_inplace(blob, i, "fsl,pins", range,
+						    len);
 			}
-			fdt_setprop_inplace(blob, i, "fsl,pins", range, len);
+
+			/* set BT656 video format */
+			ft_sethdmiinfmt(blob, "yuv422bt656");
 		}
 
-		/* set BT656 video format */
-		ft_sethdmiinfmt(blob, "yuv422bt656");
+		/* GW551x-C adds WDOG1_B external reset */
+		if (rev < 'C')
+			ft_delprop_path(blob, WDOG1_PATH,
+					"fsl,ext-reset-output");
+		break;
 	}
 
 	/* Configure DIO */
-	for (i = 0; i < gpio_cfg[board_type].num_gpios; i++) {
+	for (i = 0; i < gpio_cfg[board_type].dio_num; i++) {
 		struct dio_cfg *cfg = &gpio_cfg[board_type].dio_cfg[i];
 		char arg[10];
 
@@ -976,6 +1298,11 @@ int ft_board_setup(void *blob, bd_t *bd)
 				"no-1-8-v");
 	}
 
+#if defined(CONFIG_CMD_PCI)
+	if (!getenv("nopcifixup"))
+		ft_board_pci_fixup(blob, bd);
+#endif
+
 	/*
 	 * Peripheral Config:
 	 *  remove nodes by alias path if EEPROM config tells us the
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
index d45ed44c68..e9729f88e5 100644
--- a/board/ge/bx50v3/bx50v3.c
+++ b/board/ge/bx50v3/bx50v3.c
@@ -60,7 +60,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }
diff --git a/board/inversepath/usbarmory/usbarmory.c b/board/inversepath/usbarmory/usbarmory.c
index a809039ac5..c875e786a4 100644
--- a/board/inversepath/usbarmory/usbarmory.c
+++ b/board/inversepath/usbarmory/usbarmory.c
@@ -415,3 +415,34 @@ int checkboard(void)
 	puts("Board: Inverse Path USB armory MkI\n");
 	return 0;
 }
+
+#ifndef CONFIG_CMDLINE
+static char *ext2_argv[] = {
+	"ext2load",
+	"mmc",
+	"0:1",
+	USBARMORY_FIT_ADDR,
+	USBARMORY_FIT_PATH
+};
+
+static char *bootm_argv[] = {
+	"bootm",
+	USBARMORY_FIT_ADDR
+};
+
+int board_run_command(const char *cmdline)
+{
+	printf("%s %s %s %s %s\n", ext2_argv[0], ext2_argv[1], ext2_argv[2],
+	       ext2_argv[3], ext2_argv[4]);
+
+	if (do_ext2load(NULL, 0, 5, ext2_argv) != 0) {
+		udelay(5*1000*1000);
+		return 1;
+	}
+
+	printf("%s %s\n", bootm_argv[0], bootm_argv[1]);
+	do_bootm(NULL, 0, 2, bootm_argv);
+
+	return 1;
+}
+#endif
diff --git a/board/phytec/pcm058/Kconfig b/board/phytec/pcm058/Kconfig
new file mode 100644
index 0000000000..d099275d48
--- /dev/null
+++ b/board/phytec/pcm058/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_PCM058
+
+config SYS_BOARD
+	default "pcm058"
+
+config SYS_VENDOR
+	default "phytec"
+
+config SYS_CONFIG_NAME
+	default "pcm058"
+
+endif
diff --git a/board/phytec/pcm058/MAINTAINERS b/board/phytec/pcm058/MAINTAINERS
new file mode 100644
index 0000000000..b0ca40277f
--- /dev/null
+++ b/board/phytec/pcm058/MAINTAINERS
@@ -0,0 +1,6 @@
+PHYTEC PHYBOARD MIRA
+M:	Stefano Babic <sbabic@denx.de>
+S:	Maintained
+F:	board/phytec/pcm058/
+F:	include/configs/pcm058.h
+F:	configs/pcm058_defconfig
diff --git a/board/phytec/pcm058/Makefile b/board/phytec/pcm058/Makefile
new file mode 100644
index 0000000000..97733b110c
--- /dev/null
+++ b/board/phytec/pcm058/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := pcm058.o
diff --git a/board/phytec/pcm058/README b/board/phytec/pcm058/README
new file mode 100644
index 0000000000..3327135645
--- /dev/null
+++ b/board/phytec/pcm058/README
@@ -0,0 +1,35 @@
+Board information
+-----------------
+
+The SBC produced by Phytec has a SOM based on a i.MX6Q.
+The SOM is sold in two versions, with eMMC or with NAND. Support
+here is for the SOM with NAND.
+The evaluation board "phyBoard-Mira" is thought to be used
+together with the SOM.
+
+More information on the board can be found on manufacturer's
+website:
+
+http://www.phytec.de/produkt/single-board-computer/phyboard-mira/
+http://www.phytec.de/fileadmin/user_upload/images/content/1.Products/SOMs/phyCORE-i.MX6/L-808e_1.pdf
+
+Building U-Boot
+-------------------------------
+
+$ make pcm058_defconfig
+$ make
+
+This generates the artifacts SPL and u-boot.img.
+The SOM can boot from NAND or from SD-Card, having the SPI-NOR
+as second option.
+The dip switch "DIP-1" on the board let choose between
+NAND and SD.
+
+DIP-1 set to off:	Boot first from NAND, then try SPI
+DIP-1 set to on:	Boot first from SD, then try SPI
+
+The bootloader was tested with DIP-1 set to on. If a SD-card
+is present, then the RBL tries to load SPL from the SD Card, if not,
+RBL loads from SPI-NOR. The SPL tries then to load from the same
+device where SPL was loaded (SD or SPI). Booting from NAND is
+not supported.
diff --git a/board/phytec/pcm058/pcm058.c b/board/phytec/pcm058/pcm058.c
new file mode 100644
index 0000000000..0ba4a2e268
--- /dev/null
+++ b/board/phytec/pcm058/pcm058.c
@@ -0,0 +1,582 @@
+/*
+ * Copyright (C) 2016 Stefano Babic <sbabic@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * Please note: there are two version of the board
+ * one with NAND and the other with eMMC.
+ * Both NAND and eMMC cannot be set because they share the
+ * same pins (SD4)
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/spi.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <mmc.h>
+#include <i2c.h>
+#include <fsl_esdhc.h>
+#include <nand.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/sections.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+#define ASRC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP  |	\
+		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define NAND_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+	       PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(1, 14)
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(6, 31)
+#define USER_LED	IMX_GPIO_NR(1, 4)
+#define IMX6Q_DRIVE_STRENGTH	0x30
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+	return 0;
+}
+
+void board_turn_off_led(void)
+{
+	gpio_direction_output(USER_LED, 0);
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__GPIO1_IO14	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+/* NAND */
+static iomux_v3_cfg_t const nfc_pads[] = {
+	MX6_PAD_NANDF_CLE__NAND_CLE     | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_ALE__NAND_ALE     | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_WP_B__NAND_WP_B   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_CS0__NAND_CE0_B   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_CS1__NAND_CE1_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_CS2__NAND_CE2_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_CS3__NAND_CE3_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_SD4_CMD__NAND_RE_B      | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_SD4_CLK__NAND_WE_B      | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D0__NAND_DATA00   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D1__NAND_DATA01   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D2__NAND_DATA02   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D3__NAND_DATA03   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D4__NAND_DATA04   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D5__NAND_DATA05   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D6__NAND_DATA06   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_NANDF_D7__NAND_DATA07   | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__NAND_DQS	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+};
+
+
+/* GPIOS */
+static iomux_v3_cfg_t const gpios_pads[] = {
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 5)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{.esdhc_base = USDHC1_BASE_ADDR,
+	.max_bus_width = 4},
+#ifndef CONFIG_CMD_NAND
+	{USDHC4_BASE_ADDR},
+#endif
+};
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__SD1_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__SD1_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT0__SD1_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT1__SD1_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT2__SD1_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT3__SD1_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_EIM_BCLK__GPIO6_IO31	| MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+#ifndef CONFIG_CMD_NAND
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT4__SD4_DATA4	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT5__SD4_DATA5	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT6__SD4_DATA6	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT7__SD4_DATA7	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
+int board_mmc_get_env_dev(int devno)
+{
+	return devno - 1;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = 1; /* eMMC/uSDHC4 is always present */
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+#ifndef CONFIG_SPL_BUILD
+	int ret;
+	int i;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+			gpio_direction_input(USDHC1_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+#ifndef CONFIG_CMD_NAND
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+#endif
+		default:
+			printf("Warning: you configured more USDHC controllers"
+			       "(%d) then supported by the board (%d)\n",
+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+#else
+	struct src *psrc = (struct src *)SRC_BASE_ADDR;
+	unsigned reg = readl(&psrc->sbmr1) >> 11;
+	/*
+	 * Upon reading BOOT_CFG register the following map is done:
+	 * Bit 11 and 12 of BOOT_CFG register can determine the current
+	 * mmc port
+	 * 0x1                  SD1
+	 * 0x2                  SD2
+	 * 0x3                  SD4
+	 */
+
+	switch (reg & 0x3) {
+	case 0x0:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+		gpio_direction_input(USDHC1_CD_GPIO);
+		usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+		usdhc_cfg[0].max_bus_width = 4;
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	}
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+#endif
+}
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	gpio_direction_output(ENET_PHY_RESET_GPIO, 0);
+	mdelay(10);
+	gpio_set_value(ENET_PHY_RESET_GPIO, 1);
+	mdelay(30);
+}
+
+static void setup_spi(void)
+{
+	gpio_request(IMX_GPIO_NR(3, 19), "spi_cs0");
+	gpio_direction_output(IMX_GPIO_NR(3, 19), 1);
+
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+
+	enable_spi_clk(true, 0);
+}
+
+#ifdef CONFIG_CMD_NAND
+static void setup_gpmi_nand(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* config gpmi nand iomux */
+	imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
+
+	/* gate ENFC_CLK_ROOT clock first,before clk source switch */
+	clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+	/* config gpmi and bch clock to 100 MHz */
+	clrsetbits_le32(&mxc_ccm->cs2cdr,
+			MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+			MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+			MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
+
+	/* enable ENFC_CLK_ROOT clock */
+	setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+	/* enable gpmi and bch clock gating */
+	setbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
+
+	/* enable apbh clock gating */
+	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	if (bus != 0 || (cs != 0))
+		return -EINVAL;
+
+	return IMX_GPIO_NR(3, 19);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+
+	return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_SYS_I2C_MXC
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+#endif
+
+#ifdef CONFIG_MXC_SPI
+	setup_spi();
+#endif
+
+#ifdef CONFIG_CMD_NAND
+	setup_gpmi_nand();
+#endif
+	return 0;
+}
+
+
+#ifdef CONFIG_CMD_BMODE
+/*
+ * BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4
+ * see Table 8-11 and Table 5-9
+ *  BOOT_CFG1[7] = 1 (boot from NAND)
+ *  BOOT_CFG1[5] = 0 - raw NAND
+ *  BOOT_CFG1[4] = 0 - default pad settings
+ *  BOOT_CFG1[3:2] = 00 - devices = 1
+ *  BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3
+ *  BOOT_CFG2[4:3] = 00 - Boot Search Count = 2
+ *  BOOT_CFG2[2:1] = 01 - Pages In Block = 64
+ *  BOOT_CFG2[0] = 0 - Reset time 12ms
+ */
+static const struct boot_mode board_boot_modes[] = {
+	/* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */
+	{"nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00)},
+	{"mmc0",  MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
+	{NULL, 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#include <libfdt.h>
+
+static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_sdclk_0 = 0x00000030,
+	.dram_sdclk_1 = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_reset = 0x00000030,
+	.dram_sdcke0 = 0x00000030,
+	.dram_sdcke1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdodt0 = 0x00000030,
+	.dram_sdodt1 = 0x00000030,
+	.dram_sdqs0 = 0x00000030,
+	.dram_sdqs1 = 0x00000030,
+	.dram_sdqs2 = 0x00000030,
+	.dram_sdqs3 = 0x00000030,
+	.dram_sdqs4 = 0x00000030,
+	.dram_sdqs5 = 0x00000030,
+	.dram_sdqs6 = 0x00000030,
+	.dram_sdqs7 = 0x00000030,
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_dqm2 = 0x00000030,
+	.dram_dqm3 = 0x00000030,
+	.dram_dqm4 = 0x00000030,
+	.dram_dqm5 = 0x00000030,
+	.dram_dqm6 = 0x00000030,
+	.dram_dqm7 = 0x00000030,
+};
+
+static const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_ddr_type =  0x000C0000,
+	.grp_ddrmode_ctl =  0x00020000,
+	.grp_ddrpke =  0x00000000,
+	.grp_addds = IMX6Q_DRIVE_STRENGTH,
+	.grp_ctlds = IMX6Q_DRIVE_STRENGTH,
+	.grp_ddrmode =  0x00020000,
+	.grp_b0ds = IMX6Q_DRIVE_STRENGTH,
+	.grp_b1ds = IMX6Q_DRIVE_STRENGTH,
+	.grp_b2ds = IMX6Q_DRIVE_STRENGTH,
+	.grp_b3ds = IMX6Q_DRIVE_STRENGTH,
+	.grp_b4ds = IMX6Q_DRIVE_STRENGTH,
+	.grp_b5ds = IMX6Q_DRIVE_STRENGTH,
+	.grp_b6ds = IMX6Q_DRIVE_STRENGTH,
+	.grp_b7ds = IMX6Q_DRIVE_STRENGTH,
+};
+
+static const struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x00140014,
+	.p0_mpwldectrl1 =  0x000A0015,
+	.p1_mpwldectrl0 =  0x000A001E,
+	.p1_mpwldectrl1 =  0x000A0015,
+	.p0_mpdgctrl0 =  0x43080314,
+	.p0_mpdgctrl1 =  0x02680300,
+	.p1_mpdgctrl0 =  0x430C0318,
+	.p1_mpdgctrl1 =  0x03000254,
+	.p0_mprddlctl =  0x3A323234,
+	.p1_mprddlctl =  0x3E3C3242,
+	.p0_mpwrdlctl =  0x2A2E3632,
+	.p1_mpwrdlctl =  0x3C323E34,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 1600,
+	.density = 2,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+	.SRT       = 1,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC03, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0x00FFF300, &ccm->CCGR4);
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	/* enable AXI cache for VDOA/VPU/IPU */
+	writel(0xF00000CF, &iomux->gpr[4]);
+	/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+	writel(0x007F007F, &iomux->gpr[6]);
+	writel(0x007F007F, &iomux->gpr[7]);
+}
+
+
+static void spl_dram_init(void)
+{
+	struct mx6_ddr_sysinfo sysinfo = {
+		/* width of data bus:0=16,1=32,2=64 */
+		.dsize = 2,
+		/* config for full 4GB range so that get_mem_size() works */
+		.cs_density = 32, /* 32Gb per CS */
+		/* single chip select */
+		.ncs = 1,
+		.cs1_mirror = 0,
+		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
+		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
+		.walat = 1,	/* Write additional latency */
+		.ralat = 5,	/* Read additional latency */
+		.mif3_mode = 3,	/* Command prediction working mode */
+		.bi_on = 1,	/* Bank interleaving enabled */
+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+		.ddr_type = DDR_TYPE_DDR3,
+	};
+
+	mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+	spl_boot_list[0] = spl_boot_device();
+	printf("Boot device %x\n", spl_boot_list[0]);
+	switch (spl_boot_list[0]) {
+	case BOOT_DEVICE_SPI:
+		spl_boot_list[1] = BOOT_DEVICE_UART;
+		break;
+	case BOOT_DEVICE_MMC1:
+		spl_boot_list[1] = BOOT_DEVICE_SPI;
+		spl_boot_list[2] = BOOT_DEVICE_UART;
+		break;
+	default:
+		printf("Boot device %x\n", spl_boot_list[0]);
+	}
+}
+
+void board_init_f(ulong dummy)
+{
+#ifdef CONFIG_CMD_NAND
+	/* Enable NAND */
+	setup_gpmi_nand();
+#endif
+
+	/* setup clock gating */
+	ccgr_init();
+
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* setup AXI */
+	gpr_init();
+
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	setup_spi();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+#endif
diff --git a/board/solidrun/mx6cuboxi/mx6cuboxi.c b/board/solidrun/mx6cuboxi/mx6cuboxi.c
index bcc9729129..cafa348150 100644
--- a/board/solidrun/mx6cuboxi/mx6cuboxi.c
+++ b/board/solidrun/mx6cuboxi/mx6cuboxi.c
@@ -367,14 +367,6 @@ int checkboard(void)
 	return 0;
 }
 
-static bool is_mx6q(void)
-{
-	if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
-		return true;
-	else
-		return false;
-}
-
 int board_late_init(void)
 {
 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
@@ -383,7 +375,7 @@ int board_late_init(void)
 	else
 		setenv("board_name", "CUBOXI");
 
-	if (is_mx6q())
+	if (is_mx6dq())
 		setenv("board_rev", "MX6Q");
 	else
 		setenv("board_rev", "MX6DL");
@@ -615,7 +607,7 @@ static void spl_dram_init(int width)
 		.ddr_type = DDR_TYPE_DDR3,
 	};
 
-	if (is_cpu_type(MXC_CPU_MX6D) || is_cpu_type(MXC_CPU_MX6Q))
+	if (is_mx6dq())
 		mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
 	else
 		mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
diff --git a/board/technexion/pico-imx6ul/README b/board/technexion/pico-imx6ul/README
new file mode 100644
index 0000000000..2f66095097
--- /dev/null
+++ b/board/technexion/pico-imx6ul/README
@@ -0,0 +1,57 @@
+How to Update U-Boot on Pico-imx6ul board
+-----------------------------------------
+
+Required software on the host PC:
+
+- imx_usb_loader: https://github.com/boundarydevices/imx_usb_loader
+
+- dfu-util: http://dfu-util.sourceforge.net/releases/
+
+Build U-Boot for Pico:
+
+$ make mrproper
+$ make pico-imx6ul_defconfig
+$ make
+
+This will generate the U-Boot binary called u-boot.imx.
+
+Put pico board in USB download mode (refer to the document
+http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf page 15)
+
+Connect a USB to serial adapter between the host PC and pico
+
+Connect a USB cable between the OTG pico port and the host PC
+
+Open a terminal program such as minicom
+
+Copy u-boot.imx to the imx_usb_loader folder.
+
+Load u-boot.imx via USB:
+
+$ sudo ./imx_usb u-boot.imx
+
+Then U-Boot should start and its messages will appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
+
+Run the DFU command:
+=> dfu 0 mmc 0
+
+Transfer u-boot.imx that will be flashed into the eMMC:
+
+$ sudo dfu-util -D u-boot.imx -a boot
+
+Then on the U-Boot prompt the following message should be seen after a
+successful upgrade:
+
+#DOWNLOAD ... OK
+Ctrl+C to exit ...
+
+Remove power from the pico board.
+
+Put pico board into normal boot mode
+
+Power up the board and the new updated U-Boot should boot from eMMC.
diff --git a/board/technexion/pico-imx6ul/pico-imx6ul.c b/board/technexion/pico-imx6ul/pico-imx6ul.c
index c038d4326e..5cbf803e7e 100644
--- a/board/technexion/pico-imx6ul/pico-imx6ul.c
+++ b/board/technexion/pico-imx6ul/pico-imx6ul.c
@@ -14,11 +14,18 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/gpio.h>
 #include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
 #include <asm/io.h>
 #include <common.h>
+#include <miiphy.h>
+#include <netdev.h>
 #include <fsl_esdhc.h>
+#include <i2c.h>
 #include <linux/sizes.h>
 #include <usb.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../../freescale/common/pfuze.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -30,10 +37,113 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
 	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
 
+#define I2C_PAD_CTRL	(PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
+	PAD_CTL_ODE)
+
 #define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
 	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
 	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
 
+#define MDIO_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_SPEED_HIGH   |                                   \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL  (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+
+#define RMII_PHY_RESET IMX_GPIO_NR(1, 28)
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C2 for PMIC */
+struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode =  MX6_PAD_GPIO1_IO02__I2C1_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO02 | PC,
+		.gp = IMX_GPIO_NR(1, 2),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO1_IO03__I2C1_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO03 | PC,
+		.gp = IMX_GPIO_NR(1, 3),
+	},
+};
+#endif
+
+static iomux_v3_cfg_t const fec_pads[] = {
+	MX6_PAD_ENET1_TX_EN__ENET2_MDC		| MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA1__ENET2_MDIO	| MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	| MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET2_TX_EN__ENET2_TX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_EN__ENET2_RX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_ER__ENET2_RX_ER	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_UART4_TX_DATA__GPIO1_IO28	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_fec();
+
+	gpio_direction_output(RMII_PHY_RESET, 0);
+	/*
+	 * According to KSZ8081MNX-RNB manual:
+	 * For warm reset, the reset (RST#) pin should be asserted low for a
+	 * minimum of 500μs.  The strap-in pin values are read and updated
+	 * at the de-assertion of reset.
+	 */
+	udelay(500);
+
+	gpio_direction_output(RMII_PHY_RESET, 1);
+	/*
+	 * According to KSZ8081MNX-RNB manual:
+	 * After the de-assertion of reset, wait a minimum of 100μs before
+	 * starting programming on the MIIM (MDC/MDIO) interface.
+	 */
+	udelay(100);
+
+	return fecmxc_initialize(bis);
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+
+	ret = enable_fec_anatop_clock(1, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
 int dram_init(void)
 {
 	gd->ram_size = imx_ddr_size();
@@ -59,6 +169,9 @@ static iomux_v3_cfg_t const usdhc1_pads[] = {
 	MX6_PAD_NAND_CLE__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
 
+#define USB_OTHERREGS_OFFSET	0x800
+#define UCTRL_PWR_POL		(1 << 9)
+
 static iomux_v3_cfg_t const usb_otg_pad[] = {
 	MX6_PAD_GPIO1_IO00__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 };
@@ -96,9 +209,67 @@ int board_early_init_f(void)
 	return 0;
 }
 
+#ifdef CONFIG_POWER
+#define I2C_PMIC       0
+static struct pmic *pfuze;
+int power_init_board(void)
+{
+	int ret;
+	unsigned int reg, rev_id;
+
+	ret = power_pfuze3000_init(I2C_PMIC);
+	if (ret)
+		return ret;
+
+	pfuze = pmic_get("PFUZE3000");
+	ret = pmic_probe(pfuze);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(pfuze, PFUZE3000_DEVICEID, &reg);
+	pmic_reg_read(pfuze, PFUZE3000_REVID, &rev_id);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	pmic_reg_read(pfuze, PFUZE3000_LDOGCTL, &reg);
+	reg |= 0x1;
+	pmic_reg_write(pfuze, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1B step ramp up time from 2us to 4us/25mV */
+	pmic_reg_write(pfuze, PFUZE3000_SW1BCONF, 0x40);
+
+	/* SW1B mode to APS/PFM */
+	pmic_reg_write(pfuze, PFUZE3000_SW1BMODE, 0xc);
+
+	/* SW1B standby voltage set to 0.975V */
+	pmic_reg_write(pfuze, PFUZE3000_SW1BSTBY, 0xb);
+
+	return 0;
+}
+#endif
+
 int board_usb_phy_mode(int port)
 {
-	return USB_INIT_DEVICE;
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return USB_INIT_DEVICE;
+}
+
+int board_ehci_hcd_init(int port)
+{
+	u32 *usbnc_usb_ctrl;
+
+	if (port > 1)
+		return -EINVAL;
+
+	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
+				 port * 4);
+
+	/* Set Power polarity */
+	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
+
+	return 0;
 }
 
 int board_init(void)
@@ -106,6 +277,11 @@ int board_init(void)
 	/* Address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
+	#ifdef CONFIG_SYS_I2C_MXC
+		setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	#endif
+
+	setup_fec();
 	setup_usb();
 
 	return 0;
diff --git a/board/toradex/colibri_imx7/Kconfig b/board/toradex/colibri_imx7/Kconfig
new file mode 100644
index 0000000000..7bba26b90d
--- /dev/null
+++ b/board/toradex/colibri_imx7/Kconfig
@@ -0,0 +1,20 @@
+if TARGET_COLIBRI_IMX7
+
+config SYS_BOARD
+	default "colibri_imx7"
+
+config SYS_VENDOR
+	default "toradex"
+
+config SYS_CONFIG_NAME
+	default "colibri_imx7"
+
+config COLIBRI_IMX7_EXT_PHYCLK
+	bool "External oscillator for Ethernet PHY clock provided"
+	help
+	  Select this if your module provides a external Ethernet PHY
+	  clock source.
+	default y
+
+
+endif
diff --git a/board/toradex/colibri_imx7/MAINTAINERS b/board/toradex/colibri_imx7/MAINTAINERS
new file mode 100644
index 0000000000..5ffb2417aa
--- /dev/null
+++ b/board/toradex/colibri_imx7/MAINTAINERS
@@ -0,0 +1,6 @@
+Colibri iMX7
+M:	Stefan Agner <stefan.agner@toradex.com>
+S:	Maintained
+F:	board/toradex/colibri_imx7/
+F:	include/configs/colibri_imx7.h
+F:	configs/colibri_imx7_defconfig
diff --git a/board/toradex/colibri_imx7/Makefile b/board/toradex/colibri_imx7/Makefile
new file mode 100644
index 0000000000..ea597dec28
--- /dev/null
+++ b/board/toradex/colibri_imx7/Makefile
@@ -0,0 +1,6 @@
+# Copyright (C) 2016 Toradex AG
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := colibri_imx7.o
diff --git a/board/toradex/colibri_imx7/colibri_imx7.c b/board/toradex/colibri_imx7/colibri_imx7.c
new file mode 100644
index 0000000000..8eedd65bf0
--- /dev/null
+++ b/board/toradex/colibri_imx7/colibri_imx7.c
@@ -0,0 +1,420 @@
+/*
+ * Copyright (C) 2016 Toradex AG
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <dm.h>
+#include <dm/platform_data/serial_mxc.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <linux/sizes.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+#define ENET_PAD_CTRL_MII  (PAD_CTL_DSE_3P3V_32OHM)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+
+#define I2C_PAD_CTRL    (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
+	PAD_CTL_DSE_3P3V_49OHM)
+
+#define NAND_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU5KOHM)
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_GPIO1_IO04__I2C1_SCL | PC,
+		.gpio_mode = MX7D_PAD_GPIO1_IO04__GPIO1_IO4 | PC,
+		.gp = IMX_GPIO_NR(1, 4),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_GPIO1_IO05__I2C1_SDA | PC,
+		.gpio_mode = MX7D_PAD_GPIO1_IO05__GPIO1_IO5 | PC,
+		.gp = IMX_GPIO_NR(1, 5),
+	},
+};
+/* I2C4 for Colibri I2C */
+static struct i2c_pads_info i2c_pad_info4 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL | PC,
+		.gpio_mode = MX7D_PAD_ENET1_RGMII_TD2__GPIO7_IO8 | PC,
+		.gp = IMX_GPIO_NR(7, 8),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA | PC,
+		.gpio_mode = MX7D_PAD_ENET1_RGMII_TD3__GPIO7_IO9 | PC,
+		.gp = IMX_GPIO_NR(7, 9),
+	},
+};
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX7D_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD1_DATA3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_GPIO1_IO00__GPIO1_IO0 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#ifdef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const gpmi_pads[] = {
+	MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_CLK__NAND_CLE	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__NAND_ALE	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_STROBE__NAND_RE_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SD3_RESET_B__NAND_WE_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
+	MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	| MUX_PAD_CTRL(NAND_PAD_READY0_CTRL),
+};
+
+static void setup_gpmi_nand(void)
+{
+	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+	/* NAND_USDHC_BUS_CLK is set in rom */
+	set_clk_nand();
+}
+#endif
+
+static iomux_v3_cfg_t const usdhc3_emmc_pads[] = {
+	MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_STROBE__SD3_STROBE	 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifdef CONFIG_VIDEO_MXS
+static iomux_v3_cfg_t const lcd_pads[] = {
+	MX7D_PAD_LCD_CLK__LCD_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_ENABLE__LCD_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_HSYNC__LCD_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_VSYNC__LCD_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA00__LCD_DATA0 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA01__LCD_DATA1 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA02__LCD_DATA2 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA03__LCD_DATA3 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA04__LCD_DATA4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA05__LCD_DATA5 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA06__LCD_DATA6 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA07__LCD_DATA7 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA08__LCD_DATA8 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA09__LCD_DATA9 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA10__LCD_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA11__LCD_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA12__LCD_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA13__LCD_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA14__LCD_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA15__LCD_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA16__LCD_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX7D_PAD_LCD_DATA17__LCD_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const backlight_pads[] = {
+	/* Backlight On */
+	MX7D_PAD_SD1_WP__GPIO5_IO1 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* Backlight PWM<A> (multiplexed pin) */
+	MX7D_PAD_GPIO1_IO08__GPIO1_IO8   | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define GPIO_BL_ON IMX_GPIO_NR(5, 1)
+#define GPIO_PWM_A IMX_GPIO_NR(1, 8)
+
+static int setup_lcd(void)
+{
+	imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+
+	imx_iomux_v3_setup_multiple_pads(backlight_pads, ARRAY_SIZE(backlight_pads));
+
+	/* Set BL_ON */
+	gpio_request(GPIO_BL_ON, "BL_ON");
+	gpio_direction_output(GPIO_BL_ON, 1);
+
+	/* Set PWM<A> to full brightness (assuming inversed polarity) */
+	gpio_request(GPIO_PWM_A, "PWM<A>");
+	gpio_direction_output(GPIO_PWM_A, 0);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec1_pads[] = {
+#ifndef CONFIG_COLIBRI_IMX7_EXT_PHYCLK
+	MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 | MUX_PAD_CTRL(ENET_PAD_CTRL) | MUX_MODE_SION,
+#else
+	MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+#endif
+	MX7D_PAD_SD2_CD_B__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_SD2_WP__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	  | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(1, 0)
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{USDHC1_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+	/* USDHC1 is mmc0 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+			gpio_request(USDHC1_CD_GPIO, "usdhc1_cd");
+			gpio_direction_input(USDHC1_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	setup_iomux_fec();
+
+	ret = fecmxc_initialize_multi(bis, 0,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+	if (ret)
+		printf("FEC1 MXC: %s:failed\n", __func__);
+
+	return ret;
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
+
+#ifndef CONFIG_COLIBRI_IMX7_EXT_PHYCLK
+	/*
+	 * Use 50M anatop REF_CLK1 for ENET1, clear gpr1[13], set gpr1[17]
+	 * and output it on the pin
+	 */
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+			IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK,
+			IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK);
+#else
+	/* Use 50M external CLK for ENET1, set gpr1[13], clear gpr1[17] */
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+			IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK,
+			IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK);
+#endif
+
+	return set_clk_enet(ENET_50MHz);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+	return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+#ifdef CONFIG_SYS_I2C_MXC
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+#ifdef CONFIG_NAND_MXS
+	setup_gpmi_nand();
+#endif
+
+#ifdef CONFIG_VIDEO_MXS
+	setup_lcd();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"nand", MAKE_CFGVAL(0x40, 0x34, 0x00, 0x00)},
+	{"sd1", MAKE_CFGVAL(0x10, 0x10, 0x00, 0x00)},
+	{NULL, 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	printf("Model: Toradex Colibri iMX7%c\n",
+	       is_cpu_type(MXC_CPU_MX7D) ? 'D' : 'S');
+
+	return 0;
+}
+
+#ifdef CONFIG_USB_EHCI_MX7
+static iomux_v3_cfg_t const usb_otg2_pads[] = {
+	MX7D_PAD_UART3_CTS_B__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+	switch (port) {
+	case 0:
+		break;
+	case 1:
+		if (is_cpu_type(MXC_CPU_MX7S))
+			return -ENODEV;
+
+		imx_iomux_v3_setup_multiple_pads(usb_otg2_pads,
+						 ARRAY_SIZE(usb_otg2_pads));
+		break;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+#endif
+
+static struct mxc_serial_platdata mxc_serial_plat = {
+	.reg = (struct mxc_uart *)UART1_IPS_BASE_ADDR,
+	.use_dte = true,
+};
+
+U_BOOT_DEVICE(mxc_serial) = {
+	.name = "serial_mxc",
+	.platdata = &mxc_serial_plat,
+};
diff --git a/board/toradex/colibri_imx7/imximage.cfg b/board/toradex/colibri_imx7/imximage.cfg
new file mode 100644
index 0000000000..d891e82ae4
--- /dev/null
+++ b/board/toradex/colibri_imx7/imximage.cfg
@@ -0,0 +1,150 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *               2015 Toradex AG
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : sd
+ */
+
+BOOT_FROM	sd
+
+/*
+ * Secure boot support
+ */
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+/* IOMUXC_GPR_GPR1 */
+DATA 4 0x30340004 0x4F400005
+
+/* DDR3L */
+/* assuming MEMC_FREQ_RATIO = 2 */
+/* SRC_DDRC_RCR */
+DATA 4 0x30391000 0x00000002
+/* DDRC_MSTR */
+DATA 4 0x307a0000 0x01040001
+/* DDRC_DFIUPD0 */
+DATA 4 0x307a01a0 0x80400003
+/* DDRC_DFIUPD1 */
+DATA 4 0x307a01a4 0x00100020
+/* DDRC_DFIUPD2 */
+DATA 4 0x307a01a8 0x80100004
+/* DDRC_RFSHTMG */
+DATA 4 0x307a0064 0x00400045
+/* DDRC_MP_PCTRL_0 */
+DATA 4 0x307a0490 0x00000001
+/* DDRC_INIT0 */
+DATA 4 0x307a00d0 0x00020083
+/* DDRC_INIT1 */
+DATA 4 0x307a00d4 0x00690000
+/* DDRC_INIT3 MR0/MR1 */
+DATA 4 0x307a00dc 0x09300004
+/* DDRC_INIT4 MR2/MR3 */
+DATA 4 0x307a00e0 0x04480000
+/* DDRC_INIT5 */
+DATA 4 0x307a00e4 0x00100004
+/* DDRC_RANKCTL */
+DATA 4 0x307a00f4 0x0000033f
+/* DDRC_DRAMTMG0 */
+DATA 4 0x307a0100 0x090b090a
+/* DDRC_DRAMTMG1 */
+DATA 4 0x307a0104 0x000d020d
+/* DDRC_DRAMTMG2 */
+DATA 4 0x307a0108 0x03040307
+/* DDRC_DRAMTMG3 */
+DATA 4 0x307a010c 0x00002006
+/* DDRC_DRAMTMG4 */
+DATA 4 0x307a0110 0x04020205
+/* DDRC_DRAMTMG5 */
+DATA 4 0x307a0114 0x03030202
+/* DDRC_DRAMTMG8 */
+DATA 4 0x307a0120 0x00000803
+/* DDRC_ZQCTL0 */
+DATA 4 0x307a0180 0x00800020
+/* DDRC_ZQCTL1 */
+DATA 4 0x307a0184 0x02001000
+/* DDRC_DFITMG0 */
+DATA 4 0x307a0190 0x02098204
+/* DDRC_DFITMG1 */
+DATA 4 0x307a0194 0x00030303
+/* DDRC_ADDRMAP0 */
+DATA 4 0x307a0200 0x0000001f
+/* DDRC_ADDRMAP1 */
+DATA 4 0x307a0204 0x00080808
+/* DDRC_ADDRMAP5 */
+DATA 4 0x307a0214 0x07070707
+/* DDRC_ADDRMAP6 */
+DATA 4 0x307a0218 0x07070707
+/* DDRC_ODTCFG */
+DATA 4 0x307a0240 0x06000601
+/* DDRC_ODTMAP */
+DATA 4 0x307a0244 0x00000011
+/* SRC_DDRC_RCR */
+DATA 4 0x30391000 0x00000000
+/* DDR_PHY_PHY_CON0 */
+DATA 4 0x30790000 0x17420f40
+/* DDR_PHY_PHY_CON1 */
+DATA 4 0x30790004 0x10210100
+/* DDR_PHY_PHY_CON4 */
+DATA 4 0x30790010 0x00060807
+/* DDR_PHY_MDLL_CON0 */
+DATA 4 0x307900b0 0x1010007e
+/* DDR_PHY_DRVDS_CON0 */
+DATA 4 0x3079009c 0x00000d6e
+/* DDR_PHY_OFFSET_RD_CON0 */
+DATA 4 0x30790020 0x08080808
+/* DDR_PHY_OFFSET_WR_CON0 */
+DATA 4 0x30790030 0x08080808
+/* DDR_PHY_CMD_SDLL_CON0 */
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+/* DDR_PHY_ZQ_CON0 */
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+/* DDR_PHY_ZQ_CON1 */
+CHECK_BITS_SET 4 0x307900c4 0x1
+/* DDR_PHY_ZQ_CON0 */
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e407304
+
+/* CCM_CCGRn */
+DATA 4 0x30384130 0x00000000
+/* IOMUXC_GPR_GPR8 */
+DATA 4 0x30340020 0x00000178
+/* CCM_CCGRn */
+DATA 4 0x30384130 0x00000002
+/* DDR_PHY_LP_CON0 */
+DATA 4 0x30790018 0x0000000f
+
+/* DDRC_STAT */
+CHECK_BITS_SET 4 0x307a0004 0x1
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index 4ce74cd971..1de1e0b257 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -19,6 +19,7 @@
 #include <asm/imx-common/mxc_i2c.h>
 #include <asm/imx-common/boot_mode.h>
 #include <asm/imx-common/video.h>
+#include <asm/imx-common/sata.h>
 #include <asm/io.h>
 #include <linux/sizes.h>
 #include <common.h>
@@ -345,6 +346,12 @@ int board_early_init_f(void)
 #if defined(CONFIG_VIDEO_IPUV3)
 	setup_display();
 #endif
+#ifdef CONFIG_CMD_SATA
+	/* Only mx6q wandboard has SATA */
+	if (is_cpu_type(MXC_CPU_MX6Q))
+		setup_sata();
+#endif
+
 	return 0;
 }
 
@@ -384,7 +391,7 @@ int board_late_init(void)
 #endif
 
 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-	if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
+	if (is_mx6dq())
 		setenv("board_rev", "MX6Q");
 	else
 		setenv("board_rev", "MX6DL");
@@ -403,7 +410,7 @@ int board_init(void)
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
 	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c2_pad_info);
-	if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
+	if (is_mx6dq())
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c2_pad_info);
 	else
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c2_pad_info);
diff --git a/board/warp/warp.c b/board/warp/warp.c
index 49dfdb6717..0bc0a6a92e 100644
--- a/board/warp/warp.c
+++ b/board/warp/warp.c
@@ -46,7 +46,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }