Merge branch 'master' of git://git.denx.de/u-boot

19 files changed, 176 insertions, 143 deletions

diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c
index 13b369938f..b801150036 100644
--- a/board/davedenx/qong/qong.c
+++ b/board/davedenx/qong/qong.c
@@ -21,7 +21,6 @@
  * MA 02111-1307 USA
  */
 
-
 #include <common.h>
 #include <netdev.h>
 #include <asm/arch/mx31.h>
@@ -165,4 +164,3 @@ int board_eth_init(bd_t *bis)
 	return 0;
 #endif
 }
-
diff --git a/board/davedenx/qong/qong_fpga.h b/board/davedenx/qong/qong_fpga.h
index b1cb08adef..e8042b131e 100644
--- a/board/davedenx/qong/qong_fpga.h
+++ b/board/davedenx/qong/qong_fpga.h
@@ -38,4 +38,3 @@
 #endif
 
 #endif /* QONG_FPGA_H */
-
diff --git a/board/davinci/common/psc.c b/board/davinci/common/psc.c
index d538d51f2a..28e2a4b5b6 100644
--- a/board/davinci/common/psc.c
+++ b/board/davinci/common/psc.c
@@ -26,6 +26,14 @@
 #include <common.h>
 #include <asm/arch/hardware.h>
 
+#define PINMUX0_EMACEN (1 << 31)
+#define PINMUX0_AECS5  (1 << 11)
+#define PINMUX0_AECS4  (1 << 10)
+
+#define PINMUX1_I2C    (1 <<  7)
+#define PINMUX1_UART1  (1 <<  1)
+#define PINMUX1_UART0  (1 <<  0)
+
 /*
  * The DM6446 includes two separate power domains: "Always On" and "DSP". The
  * "Always On" power domain is always on when the chip is on. The "Always On"
@@ -115,3 +123,60 @@ void dsp_on(void)
 	REG(PSC_GBLCTL) &= ~0x1f;
 }
 #endif /* CONFIG_SYS_USE_DSPLINK */
+
+void davinci_enable_uart0(void)
+{
+	lpsc_on(DAVINCI_LPSC_UART0);
+
+	/* Bringup UART0 out of reset */
+	REG(UART0_PWREMU_MGMT) = 0x0000e003;
+
+	/* Enable UART0 MUX lines */
+	REG(PINMUX1) |= PINMUX1_UART0;
+}
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+void davinci_enable_emac(void)
+{
+	lpsc_on(DAVINCI_LPSC_EMAC);
+	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
+	lpsc_on(DAVINCI_LPSC_MDIO);
+
+	/* Enable GIO3.3V cells used for EMAC */
+	REG(VDD3P3V_PWDN) = 0;
+
+	/* Enable EMAC. */
+	REG(PINMUX0) |= PINMUX0_EMACEN;
+}
+#endif
+
+void davinci_enable_i2c(void)
+{
+	lpsc_on(DAVINCI_LPSC_I2C);
+
+	/* Enable I2C pin Mux */
+	REG(PINMUX1) |= PINMUX1_I2C;
+}
+
+void davinci_errata_workarounds(void)
+{
+	/*
+	 * Workaround for TMS320DM6446 errata 1.3.22:
+	 *   PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset
+	 *   Revision(s) Affected: 1.3 and earlier
+	 */
+	REG(PSC_SILVER_BULLET) = 0;
+
+	/*
+	 * Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR)
+	 * as suggested in TMS320DM6446 errata 2.1.2:
+	 *
+	 * On DM6446 Silicon Revision 2.1 and earlier, under certain conditions
+	 * low priority modules can occupy the bus and prevent high priority
+	 * modules like the VPSS from getting the required DDR2 throughput.
+	 * A hex value of 0x20 should provide a good ARM (cache enabled)
+	 * performance and still allow good utilization by the VPSS or other
+	 * modules.
+	 */
+	REG(VBPR) = 0x20;
+}
diff --git a/board/davinci/common/psc.h b/board/davinci/common/psc.h
index 6ab2575ae7..b2dd7b56d4 100644
--- a/board/davinci/common/psc.h
+++ b/board/davinci/common/psc.h
@@ -24,5 +24,9 @@
 
 void lpsc_on(unsigned int id);
 void dsp_on(void);
+void davinci_enable_uart0(void);
+void davinci_enable_emac(void);
+void davinci_enable_i2c(void);
+void davinci_errata_workarounds(void);
 
 #endif /* __PSC_H */
diff --git a/board/davinci/dvevm/dvevm.c b/board/davinci/dvevm/dvevm.c
index 3fe8858ee3..22308deeb0 100644
--- a/board/davinci/dvevm/dvevm.c
+++ b/board/davinci/dvevm/dvevm.c
@@ -27,7 +27,6 @@
 #include <common.h>
 #include <i2c.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -41,16 +40,13 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	/* Configure AEMIF pins (although this should be configured at boot time
+	 * with pull-up/pull-down resistors) */
+	REG(PINMUX0) = 0x00000c1f;
+
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 	lpsc_on(DAVINCI_LPSC_USB);
 
@@ -59,24 +55,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
diff --git a/board/davinci/schmoogie/schmoogie.c b/board/davinci/schmoogie/schmoogie.c
index 3504a2ec19..433769a608 100644
--- a/board/davinci/schmoogie/schmoogie.c
+++ b/board/davinci/schmoogie/schmoogie.c
@@ -27,7 +27,6 @@
 #include <common.h>
 #include <i2c.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -41,16 +40,13 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	/* Configure AEMIF pins (although this should be configured at boot time
+	 * with pull-up/pull-down resistors) */
+	REG(PINMUX0) = 0x00000c1f;
+
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 
 #if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -58,24 +54,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
@@ -87,7 +70,7 @@ int misc_init_r(void)
 	int		i = 0;
 
 	/* Set serial number from UID chip */
-	u_int8_t	crc_tbl[256] = {
+	const u_int8_t	crc_tbl[256] = {
 			0x00, 0x5e, 0xbc, 0xe2, 0x61, 0x3f, 0xdd, 0x83,
 			0xc2, 0x9c, 0x7e, 0x20, 0xa3, 0xfd, 0x1f, 0x41,
 			0x9d, 0xc3, 0x21, 0x7f, 0xfc, 0xa2, 0x40, 0x1e,
diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c
index 9296d7b634..e76f86d08c 100644
--- a/board/davinci/sffsdr/sffsdr.c
+++ b/board/davinci/sffsdr/sffsdr.c
@@ -30,7 +30,6 @@
 #include <common.h>
 #include <i2c.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -51,16 +50,9 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 
 #if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -68,24 +60,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
diff --git a/board/davinci/sonata/sonata.c b/board/davinci/sonata/sonata.c
index 6de9356c74..d56b443b20 100644
--- a/board/davinci/sonata/sonata.c
+++ b/board/davinci/sonata/sonata.c
@@ -26,7 +26,6 @@
 
 #include <common.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
 #include "../common/psc.h"
 #include "../common/misc.h"
 
@@ -40,16 +39,13 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-	/* Workaround for TMS320DM6446 errata 1.3.22 */
-	REG(PSC_SILVER_BULLET) = 0;
+	/* Configure AEMIF pins (although this should be configured at boot time
+	 * with pull-up/pull-down resistors) */
+	REG(PINMUX0) = 0x00000c1f;
+
+	davinci_errata_workarounds();
 
 	/* Power on required peripherals */
-	lpsc_on(DAVINCI_LPSC_EMAC);
-	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-	lpsc_on(DAVINCI_LPSC_MDIO);
-	lpsc_on(DAVINCI_LPSC_I2C);
-	lpsc_on(DAVINCI_LPSC_UART0);
-	lpsc_on(DAVINCI_LPSC_TIMER1);
 	lpsc_on(DAVINCI_LPSC_GPIO);
 
 #if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -57,24 +53,11 @@ int board_init(void)
 	dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-	/* Bringup UART0 out of reset */
-	REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-	/* Enable GIO3.3V cells used for EMAC */
-	REG(VDD3P3V_PWDN) = 0;
-
-	/* Enable UART0 MUX lines */
-	REG(PINMUX1) |= 1;
-
-	/* Enable EMAC and AEMIF pins */
-	REG(PINMUX0) = 0x80000c1f;
-
-	/* Enable I2C pin Mux */
-	REG(PINMUX1) |= (1 << 7);
-
-	/* Set the Bus Priority Register to appropriate value */
-	REG(VBPR) = 0x20;
+	davinci_enable_uart0();
+	davinci_enable_emac();
+	davinci_enable_i2c();
 
+	lpsc_on(DAVINCI_LPSC_TIMER1);
 	timer_init();
 
 	return(0);
diff --git a/board/keymile/mgcoge/mgcoge.c b/board/keymile/mgcoge/mgcoge.c
index 5c50739644..0e3aa49df9 100644
--- a/board/keymile/mgcoge/mgcoge.c
+++ b/board/keymile/mgcoge/mgcoge.c
@@ -325,6 +325,7 @@ void ft_blob_update (void *blob, bd_t *bd)
 {
 	ulong memory_data[2] = {0};
 	ulong flash_data[8] = {0};
+	flash_info_t	*info;
 
 	memory_data[0] = cpu_to_be32 (bd->bi_memstart);
 	memory_data[1] = cpu_to_be32 (bd->bi_memsize);
@@ -332,12 +333,14 @@ void ft_blob_update (void *blob, bd_t *bd)
 				sizeof (memory_data));
 
 	/* update Flash addr, size */
+	info = flash_get_info(CONFIG_SYS_FLASH_BASE);
 	flash_data[2] = cpu_to_be32 (CONFIG_SYS_FLASH_BASE);
-	flash_data[3] = cpu_to_be32 (CONFIG_SYS_FLASH_SIZE);
+	flash_data[3] = cpu_to_be32 (info->size);
 	flash_data[4] = cpu_to_be32 (5);
 	flash_data[5] = cpu_to_be32 (0);
+	info = flash_get_info(CONFIG_SYS_FLASH_BASE_1);
 	flash_data[6] = cpu_to_be32 (CONFIG_SYS_FLASH_BASE_1);
-	flash_data[7] = cpu_to_be32 (CONFIG_SYS_FLASH_SIZE_1);
+	flash_data[7] = cpu_to_be32 (info->size);
 	fdt_set_node_and_value (blob, "/localbus", "ranges", flash_data,
 				sizeof (flash_data));
 	/* MAC addr */
diff --git a/board/keymile/mgsuvd/mgsuvd.c b/board/keymile/mgsuvd/mgsuvd.c
index 02baf622ee..e7bfa31250 100644
--- a/board/keymile/mgsuvd/mgsuvd.c
+++ b/board/keymile/mgsuvd/mgsuvd.c
@@ -168,6 +168,7 @@ void ft_blob_update (void *blob, bd_t *bd)
 	ulong brg_data[1] = {0};
 	ulong memory_data[2] = {0};
 	ulong flash_data[4] = {0};
+	ulong flash_reg[3] = {0};
 
 	memory_data[0] = cpu_to_be32 (bd->bi_memstart);
 	memory_data[1] = cpu_to_be32 (bd->bi_memsize);
@@ -179,6 +180,10 @@ void ft_blob_update (void *blob, bd_t *bd)
 	fdt_set_node_and_value (blob, "/localbus", "ranges", flash_data,
 				sizeof (flash_data));
 
+	flash_reg[2] = cpu_to_be32 (bd->bi_flashsize);
+	fdt_set_node_and_value (blob, "/localbus/flash@0,0", "reg", flash_reg,
+				sizeof (flash_reg));
+
 	/* BRG */
 	brg_data[0] = cpu_to_be32 (bd->bi_busfreq);
 	fdt_set_node_and_value (blob, "/soc/cpm", "brg-frequency", brg_data,
diff --git a/board/omap3/beagle/beagle.c b/board/omap3/beagle/beagle.c
index ecdea09382..7377058f79 100644
--- a/board/omap3/beagle/beagle.c
+++ b/board/omap3/beagle/beagle.c
@@ -36,6 +36,8 @@
 #include <asm/mach-types.h>
 #include "beagle.h"
 
+static int beagle_revision_c;
+
 /******************************************************************************
  * Routine: board_init
  * Description: Early hardware init.
@@ -54,6 +56,43 @@ int board_init(void)
 }
 
 /******************************************************************************
+ * Routine: beagle_get_revision
+ * Description: Return revision of the BeagleBoard this code is running on.
+ *              If it is a revision Ax/Bx board, this function returns 0,
+ *              on a revision C board you will get a 1.
+ *****************************************************************************/
+int beagle_get_revision(void)
+{
+	return beagle_revision_c;
+}
+
+/******************************************************************************
+ * Routine: beagle_identify
+ * Description: Detect if we are running on a Beagle revision Ax/Bx or
+ *              Cx. This can be done by GPIO_171. If this is low, we are
+ *              running on a revision C board.
+ *****************************************************************************/
+void beagle_identify(void)
+{
+	gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+	/* Configure GPIO 171 as input */
+	writel(readl(&gpio6_base->oe) | GPIO11, &gpio6_base->oe);
+
+	/* Get value of GPIO 171 */
+	beagle_revision_c = readl(&gpio6_base->datain) & BOARD_REVISION_MASK;
+
+	printf("Board revision ");
+	if (beagle_revision_c) {
+		printf("Ax/Bx\n");
+		beagle_revision_c = 0;
+	} else {
+		printf("C\n");
+		beagle_revision_c = 1;
+	}
+}
+
+/******************************************************************************
  * Routine: misc_init_r
  * Description: Configure board specific parts
  *****************************************************************************/
@@ -75,6 +114,8 @@ int misc_init_r(void)
 	writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
 		GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
 
+	beagle_identify();
+
 	return 0;
 }
 
diff --git a/board/omap3/beagle/beagle.h b/board/omap3/beagle/beagle.h
index 6511ffaaa7..d66f159d27 100644
--- a/board/omap3/beagle/beagle.h
+++ b/board/omap3/beagle/beagle.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3530",
 	"OMAP3 Beagle board",
 #if defined(CONFIG_ENV_IS_IN_ONENAND)
 	"OneNAND",
@@ -36,6 +35,8 @@ const omap3_sysinfo sysinfo = {
 #endif
 };
 
+#define BOARD_REVISION_MASK	(0x1 << 11)
+
 /*
  * IEN  - Input Enable
  * IDIS - Input Disable
diff --git a/board/omap3/evm/evm.h b/board/omap3/evm/evm.h
index 4ecea7f42b..199824f4c4 100644
--- a/board/omap3/evm/evm.h
+++ b/board/omap3/evm/evm.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	OMAP3EVM_V1,
 	OMAP3EVM_V2,
 	DDR_DISCRETE,
-	"35X-Family",
 	"OMAP3 EVM board",
 #if defined(CONFIG_ENV_IS_IN_ONENAND)
 	"OneNAND",
diff --git a/board/omap3/overo/Makefile b/board/omap3/overo/Makefile
index c16562998a..dd673ca4d4 100644
--- a/board/omap3/overo/Makefile
+++ b/board/omap3/overo/Makefile
@@ -44,4 +44,5 @@ distclean:	clean
 # defines $(obj).depend target
 include $(SRCTREE)/rules.mk
 
+#########################################################################
 sinclude $(obj).depend
diff --git a/board/omap3/overo/overo.c b/board/omap3/overo/overo.c
index 796412362a..48375ad01e 100644
--- a/board/omap3/overo/overo.c
+++ b/board/omap3/overo/overo.c
@@ -58,21 +58,8 @@ int board_init(void)
  *****************************************************************************/
 int misc_init_r(void)
 {
-	gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
-	gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
-
 	power_init_r();
 
-	/* Configure GPIOs to output */
-	writel(~((GPIO10) | GPIO9 | GPIO3 | GPIO2), &gpio6_base->oe);
-	writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
-		GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
-
-	/* Set GPIOs */
-	writel(GPIO10 | GPIO9 | GPIO3 | GPIO2, &gpio6_base->setdataout);
-	writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
-		GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
-
 	return 0;
 }
 
diff --git a/board/omap3/overo/overo.h b/board/omap3/overo/overo.h
index 3c1b6bcbf8..71de3f10d3 100644
--- a/board/omap3/overo/overo.h
+++ b/board/omap3/overo/overo.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3503",
 	"Gumstix Overo board",
 #if defined(CONFIG_ENV_IS_IN_ONENAND)
 	"OneNAND",
@@ -130,7 +129,8 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0)) /*GPMC_nWP*/\
  MUX_VAL(CP(GPMC_WAIT0),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT0*/\
  MUX_VAL(CP(GPMC_WAIT1),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT1*/\
- MUX_VAL(CP(GPMC_WAIT2),	(IEN  | PTU | EN  | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_WAIT2),	(IEN  | PTU | DIS | M4)) /*GPIO_64*/\
+							/* - SMSC911X_NRES*/\
  MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M0)) /*GPMC_nCS3*/\
  /*DSS*/\
  MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
@@ -184,7 +184,7 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(CAM_STROBE),	(IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
  MUX_VAL(CP(CSI2_DX0),		(IEN  | PTD | DIS | M0)) /*CSI2_DX0*/\
  MUX_VAL(CP(CSI2_DY0),		(IEN  | PTD | DIS | M0)) /*CSI2_DY0*/\
- MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | EN  | M4)) /*GPIO_114*/\
  MUX_VAL(CP(CSI2_DY1),		(IEN  | PTU | EN  | M4)) /*GPIO_115*/\
  /*Audio Interface */\
  MUX_VAL(CP(MCBSP2_FSX),	(IEN  | PTD | DIS | M0)) /*McBSP2_FSX*/\
@@ -218,10 +218,10 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(MCBSP3_DR),		(IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
  MUX_VAL(CP(MCBSP3_CLKX),	(IDIS | PTD | DIS | M1)) /*UART2_TX*/\
  MUX_VAL(CP(MCBSP3_FSX),	(IEN  | PTD | DIS | M1)) /*UART2_RX*/\
- MUX_VAL(CP(UART2_CTS),		(IDIS | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
- MUX_VAL(CP(UART2_RTS),		(IDIS | PTD | DIS | M4)) /*GPIO_145*/\
- MUX_VAL(CP(UART2_TX),		(IDIS | PTD | DIS | M4)) /*GPIO_146*/\
- MUX_VAL(CP(UART2_RX),		(IDIS | PTD | DIS | M4)) /*GPIO_147*/\
+ MUX_VAL(CP(UART2_CTS),		(IEN  | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
+ MUX_VAL(CP(UART2_RTS),		(IEN  | PTD | DIS | M4)) /*GPIO_145*/\
+ MUX_VAL(CP(UART2_TX),		(IEN  | PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX),		(IEN  | PTD | DIS | M4)) /*GPIO_147*/\
  MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0)) /*UART1_TX*/\
  MUX_VAL(CP(UART1_RTS),		(IEN  | PTU | DIS | M4)) /*GPIO_149*/ \
  MUX_VAL(CP(UART1_CTS),		(IEN  | PTU | DIS | M4)) /*GPIO_150-MMC3_WP*/\
@@ -271,7 +271,8 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(MCSPI1_SOMI),	(IEN  | PTD | DIS | M0)) /*McSPI1_SOMI */\
  MUX_VAL(CP(MCSPI1_CS0),	(IEN  | PTD | EN  | M0)) /*McSPI1_CS0*/\
  MUX_VAL(CP(MCSPI1_CS1),	(IDIS | PTD | EN  | M0)) /*McSPI1_CS1*/\
- MUX_VAL(CP(MCSPI1_CS2),	(IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ MUX_VAL(CP(MCSPI1_CS2),	(IEN  | PTD | DIS | M4)) /*GPIO_176*/\
+							/* - SMSC911X_IRQ*/\
  MUX_VAL(CP(MCSPI1_CS3),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA2*/\
  MUX_VAL(CP(MCSPI2_CLK),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA7*/\
  MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA4*/\
@@ -306,7 +307,7 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(ETK_D8_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT6*/\
  MUX_VAL(CP(ETK_D9_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT5*/\
  MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
- MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | EN  | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
  MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DIR*/\
  MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M3)) /*HSUSB2_NXT*/\
  MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DATA0*/\
diff --git a/board/omap3/pandora/pandora.h b/board/omap3/pandora/pandora.h
index 8525a03c5f..dd09f12bcc 100644
--- a/board/omap3/pandora/pandora.h
+++ b/board/omap3/pandora/pandora.h
@@ -27,7 +27,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3530",
 	"OMAP3 Pandora",
 	"NAND",
 };
@@ -200,12 +199,12 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(MMC2_DAT7),		(IEN  | PTU | EN  | M1)) /*MMC2_CLKIN*/\
  MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTD | DIS | M4)) /*GPIO_127 - MMC2_WP*/\
  /*SDIO Interface to WIFI Module*/\
- MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | EN  | M2)) /*MMC3_CLK*/\
- MUX_VAL(CP(ETK_CTL_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_CMD*/\
- MUX_VAL(CP(ETK_D4_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT0*/\
- MUX_VAL(CP(ETK_D5_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT1*/\
- MUX_VAL(CP(ETK_D6_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT2*/\
- MUX_VAL(CP(ETK_D3_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_DAT3*/\
+ MUX_VAL(CP(ETK_CLK_ES2),	(IEN  | PTD | DIS | M2)) /*MMC3_CLK*/\
+ MUX_VAL(CP(ETK_CTL_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_CMD*/\
+ MUX_VAL(CP(ETK_D4_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT0*/\
+ MUX_VAL(CP(ETK_D5_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT1*/\
+ MUX_VAL(CP(ETK_D6_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT2*/\
+ MUX_VAL(CP(ETK_D3_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT3*/\
  /*Audio Interface To Bluetooth chip*/\
  MUX_VAL(CP(MCBSP3_DX),		(IDIS | PTD | DIS | M0)) /*McBSP3_DX*/\
  MUX_VAL(CP(MCBSP3_DR),		(IEN  | PTD | DIS | M0)) /*McBSP3_DR*/\
diff --git a/board/omap3/zoom1/zoom1.h b/board/omap3/zoom1/zoom1.h
index d3894928a5..bc8fba89eb 100644
--- a/board/omap3/zoom1/zoom1.h
+++ b/board/omap3/zoom1/zoom1.h
@@ -31,7 +31,6 @@ const omap3_sysinfo sysinfo = {
 	SDP_3430_V1,
 	SDP_3430_V2,
 	DDR_STACKED,
-	"3430",
 	"OMAP3 Zoom MDK Rev 1",
 	"NAND",
 };
diff --git a/board/st/nmdk8815/nmdk8815.c b/board/st/nmdk8815/nmdk8815.c
index c54eac12c7..edf46262f5 100644
--- a/board/st/nmdk8815/nmdk8815.c
+++ b/board/st/nmdk8815/nmdk8815.c
@@ -49,8 +49,11 @@ int board_init(void)
 	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
 	writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);
 
-	icache_enable();
+	/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
+	writel(0x0000305b, REG_FSMC_BCR1);
+	writel(0x00033f33, REG_FSMC_BTR1);
 
+	icache_enable();
 	return 0;
 }