arm: Remove portuxg20, stamp9g20 boards

These boards have not been converted to generic board by the deadline.
Remove them.

Signed-off-by: Simon Glass <sjg@chromium.org>

5 files changed, 0 insertions, 317 deletions

diff --git a/board/taskit/stamp9g20/Kconfig b/board/taskit/stamp9g20/Kconfig
deleted file mode 100644
index 1121dacfc7..0000000000
--- a/board/taskit/stamp9g20/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_STAMP9G20
-
-config SYS_BOARD
-	default "stamp9g20"
-
-config SYS_VENDOR
-	default "taskit"
-
-config SYS_CONFIG_NAME
-	default "stamp9g20"
-
-endif
diff --git a/board/taskit/stamp9g20/MAINTAINERS b/board/taskit/stamp9g20/MAINTAINERS
deleted file mode 100644
index a91c1960cb..0000000000
--- a/board/taskit/stamp9g20/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-STAMP9G20 BOARD
-M:	Markus Hubig <mhubig@imko.de>
-S:	Maintained
-F:	board/taskit/stamp9g20/
-F:	include/configs/stamp9g20.h
-F:	configs/portuxg20_defconfig
-F:	configs/stamp9g20_defconfig
diff --git a/board/taskit/stamp9g20/Makefile b/board/taskit/stamp9g20/Makefile
deleted file mode 100644
index d015e0f740..0000000000
--- a/board/taskit/stamp9g20/Makefile
+++ /dev/null
@@ -1,17 +0,0 @@
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (C) Copyright 2008
-# Stelian Pop <stelian@popies.net>
-# Lead Tech Design <www.leadtechdesign.com>
-#
-# (C) Copyright 2012
-# Markus Hubig <mhubig@imko.de>
-# IMKO GmbH <www.imko.de>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	+= stamp9g20.o
-obj-y	+= led.o
diff --git a/board/taskit/stamp9g20/led.c b/board/taskit/stamp9g20/led.c
deleted file mode 100644
index c5831258bd..0000000000
--- a/board/taskit/stamp9g20/led.c
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix@windriver.com>
- * (C) Copyright 2009
- * Eric Benard <eric@eukrea.com>
- *
- * (C) Copyright 2012
- * Markus Hubig <mhubig@imko.de>
- * IMKO GmbH <www.imko.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91_pmc.h>
-#include <status_led.h>
-
-static unsigned int saved_state[3] = {STATUS_LED_OFF,
-	STATUS_LED_OFF, STATUS_LED_OFF};
-
-void coloured_LED_init(void)
-{
-	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
-	/* Enable the clock */
-	writel(ATMEL_ID_PIOC, &pmc->pcer);
-
-	at91_set_gpio_output(CONFIG_RED_LED, 1);
-	at91_set_gpio_output(CONFIG_GREEN_LED, 1);
-	at91_set_gpio_output(CONFIG_YELLOW_LED, 1);
-
-	at91_set_gpio_value(CONFIG_RED_LED, 0);
-	at91_set_gpio_value(CONFIG_GREEN_LED, 1);
-	at91_set_gpio_value(CONFIG_YELLOW_LED, 0);
-}
-
-void red_led_on(void)
-{
-	at91_set_gpio_value(CONFIG_RED_LED, 1);
-	saved_state[STATUS_LED_RED] = STATUS_LED_ON;
-}
-
-void red_led_off(void)
-{
-	at91_set_gpio_value(CONFIG_RED_LED, 0);
-	saved_state[STATUS_LED_RED] = STATUS_LED_OFF;
-}
-
-void green_led_on(void)
-{
-	at91_set_gpio_value(CONFIG_GREEN_LED, 1);
-	saved_state[STATUS_LED_GREEN] = STATUS_LED_ON;
-}
-
-void green_led_off(void)
-{
-	at91_set_gpio_value(CONFIG_GREEN_LED, 0);
-	saved_state[STATUS_LED_GREEN] = STATUS_LED_OFF;
-}
-
-void yellow_led_on(void)
-{
-	at91_set_gpio_value(CONFIG_YELLOW_LED, 1);
-	saved_state[STATUS_LED_YELLOW] = STATUS_LED_ON;
-}
-
-void yellow_led_off(void)
-{
-	at91_set_gpio_value(CONFIG_YELLOW_LED, 0);
-	saved_state[STATUS_LED_YELLOW] = STATUS_LED_OFF;
-}
-
-void __led_init(led_id_t mask, int state)
-{
-	__led_set(mask, state);
-}
-
-void __led_toggle(led_id_t mask)
-{
-	if (STATUS_LED_RED == mask) {
-		if (STATUS_LED_ON == saved_state[STATUS_LED_RED])
-			red_led_off();
-		else
-			red_led_on();
-
-	} else if (STATUS_LED_GREEN == mask) {
-		if (STATUS_LED_ON == saved_state[STATUS_LED_GREEN])
-			green_led_off();
-		else
-			green_led_on();
-
-	} else if (STATUS_LED_YELLOW == mask) {
-		if (STATUS_LED_ON == saved_state[STATUS_LED_YELLOW])
-			yellow_led_off();
-		else
-			yellow_led_on();
-	}
-}
-
-void __led_set(led_id_t mask, int state)
-{
-	if (STATUS_LED_RED == mask) {
-		if (STATUS_LED_ON == state)
-			red_led_on();
-		else
-			red_led_off();
-
-	} else if (STATUS_LED_GREEN == mask) {
-		if (STATUS_LED_ON == state)
-			green_led_on();
-		else
-			green_led_off();
-
-	} else if (STATUS_LED_YELLOW == mask) {
-		if (STATUS_LED_ON == state)
-			yellow_led_on();
-		else
-			yellow_led_off();
-	}
-}
diff --git a/board/taskit/stamp9g20/stamp9g20.c b/board/taskit/stamp9g20/stamp9g20.c
deleted file mode 100644
index 27cdf77f01..0000000000
--- a/board/taskit/stamp9g20/stamp9g20.c
+++ /dev/null
@@ -1,159 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian@popies.net>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * Achim Ehrlich <aehrlich@taskit.de>
- * taskit GmbH <www.taskit.de>
- *
- * (C) Copyright 2012-
- * Markus Hubig <mhubig@imko.de>
- * IMKO GmbH <www.imko.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/at91sam9260_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/gpio.h>
-#include <watchdog.h>
-
-#ifdef CONFIG_MACB
-# include <net.h>
-# include <netdev.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static void stamp9G20_nand_hw_init(void)
-{
-	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
-	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
-	unsigned long csa;
-
-	/* Assign CS3 to NAND/SmartMedia Interface */
-	csa = readl(&matrix->ebicsa);
-	csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
-	writel(csa, &matrix->ebicsa);
-
-	/* Configure SMC CS3 for NAND/SmartMedia */
-	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
-		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
-		&smc->cs[3].setup);
-	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
-		AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
-		&smc->cs[3].pulse);
-	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
-		&smc->cs[3].cycle);
-	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
-		AT91_SMC_MODE_EXNW_DISABLE |
-		AT91_SMC_MODE_DBW_8 |
-		AT91_SMC_MODE_TDF_CYCLE(2),
-		&smc->cs[3].mode);
-
-	/* Configure RDY/BSY */
-	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
-
-	/* Enable NandFlash */
-	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
-}
-
-#ifdef CONFIG_MACB
-static void stamp9G20_macb_hw_init(void)
-{
-	struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
-
-	/* Enable the PHY Chip via PA26 on the Stamp 2 Adaptor */
-	at91_set_gpio_output(AT91_PIN_PA26, 0);
-
-	/*
-	 * Disable pull-up on:
-	 *	RXDV (PA17) => PHY normal mode (not Test mode)
-	 *	ERX0 (PA14) => PHY ADDR0
-	 *	ERX1 (PA15) => PHY ADDR1
-	 *	ERX2 (PA25) => PHY ADDR2
-	 *	ERX3 (PA26) => PHY ADDR3
-	 *	ECRS (PA28) => PHY ADDR4  => PHYADDR = 0x0
-	 *
-	 * PHY has internal pull-down
-	 */
-	writel(pin_to_mask(AT91_PIN_PA14) |
-		pin_to_mask(AT91_PIN_PA15) |
-		pin_to_mask(AT91_PIN_PA17) |
-		pin_to_mask(AT91_PIN_PA18) |
-		pin_to_mask(AT91_PIN_PA28),
-		&pioa->pudr);
-
-	at91_phy_reset();
-
-	/* Re-enable pull-up */
-	writel(pin_to_mask(AT91_PIN_PA14) |
-		pin_to_mask(AT91_PIN_PA15) |
-		pin_to_mask(AT91_PIN_PA17) |
-		pin_to_mask(AT91_PIN_PA18) |
-		pin_to_mask(AT91_PIN_PA28),
-		&pioa->puer);
-
-	/* Initialize EMAC=MACB hardware */
-	at91_macb_hw_init();
-}
-#endif /* CONFIG_MACB */
-
-int board_early_init_f(void)
-{
-	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
-	/* Enable clocks for all PIOs */
-	writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
-		(1 << ATMEL_ID_PIOC), &pmc->pcer);
-
-	return 0;
-}
-
-int board_postclk_init(void)
-{
-	/*
-	 * Initialize the serial interface here, because be need a running
-	 * timer to set PC9 to high and wait for some time to enable the
-	 * level converter of the RS232 interface on the PortuxG20 board.
-	 */
-
-#ifdef CONFIG_PORTUXG20
-	at91_set_gpio_output(AT91_PIN_PC9, 1);
-	mdelay(1);
-#endif
-	at91_seriald_hw_init();
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* Adress of boot parameters */
-	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
-	stamp9G20_nand_hw_init();
-#ifdef CONFIG_MACB
-	stamp9G20_macb_hw_init();
-#endif
-	return 0;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(
-		(void *)CONFIG_SYS_SDRAM_BASE,
-		CONFIG_SYS_SDRAM_SIZE);
-	return 0;
-}
-
-#ifdef CONFIG_MACB
-int board_eth_init(bd_t *bis)
-{
-	return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
-}
-#endif /* CONFIG_MACB */