Merge branch 'next'

16 files changed, 827 insertions, 19 deletions

diff --git a/board/freescale/mpc8315erdb/mpc8315erdb.c b/board/freescale/mpc8315erdb/mpc8315erdb.c
index ea4b04fd3d..f80b0ba4a5 100644
--- a/board/freescale/mpc8315erdb/mpc8315erdb.c
+++ b/board/freescale/mpc8315erdb/mpc8315erdb.c
@@ -30,6 +30,7 @@
 #include <pci.h>
 #include <mpc83xx.h>
 #include <netdev.h>
+#include <asm/io.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -95,12 +96,45 @@ static struct pci_region pci_regions[] = {
 	}
 };
 
+static struct pci_region pcie_regions_0[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE1_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+		.size = CONFIG_SYS_PCIE1_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+static struct pci_region pcie_regions_1[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE2_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE2_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
+		.size = CONFIG_SYS_PCIE2_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
 void pci_init_board(void)
 {
 	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile sysconf83xx_t *sysconf = &immr->sysconf;
 	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
 	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	volatile law83xx_t *pcie_law = sysconf->pcielaw;
 	struct pci_region *reg[] = { pci_regions };
+	struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
 	int warmboot;
 
 	/* Enable all 3 PCI_CLK_OUTPUTs. */
@@ -119,6 +153,24 @@ void pci_init_board(void)
 	warmboot |= immr->pmc.pmccr1 & PMCCR1_POWER_OFF;
 
 	mpc83xx_pci_init(1, reg, warmboot);
+
+	/* Configure the clock for PCIE controller */
+	clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM | SCCR_PCIEXP2CM,
+				    SCCR_PCIEXP1CM_1 | SCCR_PCIEXP2CM_1);
+
+	/* Deassert the resets in the control register */
+	out_be32(&sysconf->pecr1, 0xE0008000);
+	out_be32(&sysconf->pecr2, 0xE0008000);
+	udelay(2000);
+
+	/* Configure PCI Express Local Access Windows */
+	out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	mpc83xx_pcie_init(2, pcie_reg, warmboot);
 }
 
 #if defined(CONFIG_OF_BOARD_SETUP)
diff --git a/board/freescale/mpc8349emds/pci.c b/board/freescale/mpc8349emds/pci.c
index ad7bf5d508..af0b1da13d 100644
--- a/board/freescale/mpc8349emds/pci.c
+++ b/board/freescale/mpc8349emds/pci.c
@@ -171,15 +171,10 @@ void pci_init_board(void)
 void pci_init_board(void)
 {
 	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
-	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
 	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
 	volatile pcictrl83xx_t *pci_ctrl = &immr->pci_ctrl[0];
 	struct pci_region *reg[] = { pci1_regions };
 
-	/* Enable all 8 PCI_CLK_OUTPUTS */
-	clk->occr = 0xff000000;
-	udelay(2000);
-
 	/* Configure PCI Local Access Windows */
 	pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
 	pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
@@ -187,8 +182,6 @@ void pci_init_board(void)
 	pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
 	pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M;
 
-	udelay(2000);
-
 	mpc83xx_pci_init(1, reg, 0);
 
 	/* Configure PCI Inbound Translation Windows (3 1MB windows) */
diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c
index acf8ada7b2..156d8089a1 100644
--- a/board/freescale/mpc837xemds/mpc837xemds.c
+++ b/board/freescale/mpc837xemds/mpc837xemds.c
@@ -18,6 +18,7 @@
 #include <tsec.h>
 #include <libfdt.h>
 #include <fdt_support.h>
+#include "pci.h"
 #include "../common/pq-mds-pib.h"
 
 int board_early_init_f(void)
@@ -38,14 +39,10 @@ int board_early_init_f(void)
 	case SPR_8377:
 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
 				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
-		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
-				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
 		break;
 	case SPR_8378:
 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII,
 				 FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V);
-		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
-				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
 		break;
 	case SPR_8379:
 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
@@ -316,6 +313,7 @@ void ft_board_setup(void *blob, bd_t *bd)
 	ft_pci_setup(blob, bd);
 	if (board_pci_host_broken())
 		ft_pci_fixup(blob, bd);
+	ft_pcie_fixup(blob, bd);
 #endif
 }
 #endif /* CONFIG_OF_BOARD_SETUP */
diff --git a/board/freescale/mpc837xemds/pci.c b/board/freescale/mpc837xemds/pci.c
index df4e748e97..31116b31ce 100644
--- a/board/freescale/mpc837xemds/pci.c
+++ b/board/freescale/mpc837xemds/pci.c
@@ -16,7 +16,9 @@
 #include <mpc83xx.h>
 #include <pci.h>
 #include <i2c.h>
+#include <fdt_support.h>
 #include <asm/fsl_i2c.h>
+#include <asm/fsl_serdes.h>
 
 #if defined(CONFIG_PCI)
 static struct pci_region pci_regions[] = {
@@ -40,15 +42,59 @@ static struct pci_region pci_regions[] = {
 	}
 };
 
+static struct pci_region pcie_regions_0[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE1_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+		.size = CONFIG_SYS_PCIE1_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+static struct pci_region pcie_regions_1[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE2_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE2_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
+		.size = CONFIG_SYS_PCIE2_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+static int is_pex_x2(void)
+{
+	const char *pex_x2 = getenv("pex_x2");
+
+	if (pex_x2 && !strcmp(pex_x2, "yes"))
+		return 1;
+	return 0;
+}
+
 void pci_init_board(void)
 {
 	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile sysconf83xx_t *sysconf = &immr->sysconf;
 	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
 	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	volatile law83xx_t *pcie_law = sysconf->pcielaw;
 	struct pci_region *reg[] = { pci_regions };
+	struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
+	u32 spridr = in_be32(&immr->sysconf.spridr);
+	int pex2 = is_pex_x2();
 
 	if (board_pci_host_broken())
-		return;
+		goto skip_pci;
 
 	/* Enable all 5 PCI_CLK_OUTPUTS */
 	clk->occr |= 0xf8000000;
@@ -64,5 +110,46 @@ void pci_init_board(void)
 	udelay(2000);
 
 	mpc83xx_pci_init(1, reg, 0);
+skip_pci:
+	/* There is no PEX in MPC8379 parts. */
+	if (PARTID_NO_E(spridr) == SPR_8379)
+		return;
+
+	/* Configure the clock for PCIE controller */
+	clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM | SCCR_PCIEXP2CM,
+				    SCCR_PCIEXP1CM_1 | SCCR_PCIEXP2CM_1);
+
+	/* Deassert the resets in the control register */
+	out_be32(&sysconf->pecr1, 0xE0008000);
+	if (!pex2)
+		out_be32(&sysconf->pecr2, 0xE0008000);
+	udelay(2000);
+
+	/* Configure PCI Express Local Access Windows */
+	out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	if (pex2)
+		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX_X2,
+				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+	else
+		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
+				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+	mpc83xx_pcie_init(pex2 ? 1 : 2, pcie_reg, 0);
+}
+
+void ft_pcie_fixup(void *blob, bd_t *bd)
+{
+	const char *status = "disabled (PCIE1 is x2)";
+
+	if (!is_pex_x2())
+		return;
+
+	do_fixup_by_path(blob, "pci2", "status", status,
+			 strlen(status) + 1, 1);
 }
 #endif /* CONFIG_PCI */
diff --git a/board/freescale/mpc837xemds/pci.h b/board/freescale/mpc837xemds/pci.h
new file mode 100644
index 0000000000..fd7a916af8
--- /dev/null
+++ b/board/freescale/mpc837xemds/pci.h
@@ -0,0 +1,6 @@
+#ifndef __BOARD_MPC837XEMDS_PCI_H
+#define __BOARD_MPC837XEMDS_PCI_H
+
+extern void ft_pcie_fixup(void *blob, bd_t *bd);
+
+#endif /* __BOARD_MPC837XEMDS_PCI_H */
diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c
index a4cf24cf72..1338950814 100644
--- a/board/keymile/common/common.c
+++ b/board/keymile/common/common.c
@@ -22,10 +22,14 @@
  */
 
 #include <common.h>
+#if defined(CONFIG_MGCOGE)
 #include <mpc8260.h>
+#endif
 #include <ioports.h>
 #include <malloc.h>
 #include <hush.h>
+#include <net.h>
+#include <asm/io.h>
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
 #include <libfdt.h>
@@ -33,8 +37,6 @@
 
 #if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
 #include <i2c.h>
-#endif
-#include <asm/io.h>
 
 extern int i2c_soft_read_pin (void);
 
@@ -495,6 +497,7 @@ void i2c_init_board(void)
 #endif
 }
 #endif
+#endif
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
 int fdt_set_node_and_value (void *blob,
@@ -521,3 +524,19 @@ int fdt_set_node_and_value (void *blob,
 	return ret;
 }
 #endif
+
+int ethernet_present (void)
+{
+	return (in_8((u8 *)CONFIG_SYS_PIGGY_BASE + CONFIG_SYS_SLOT_ID_OFF) & 0x80);
+}
+
+int board_eth_init (bd_t *bis)
+{
+#ifdef CONFIG_KEYMILE_HDLC_ENET
+	(void)keymile_hdlc_enet_initialize (bis);
+#endif
+	if (ethernet_present ()) {
+		return -1;
+	}
+	return 0;
+}
diff --git a/board/keymile/common/common.h b/board/keymile/common/common.h
new file mode 100644
index 0000000000..d3d681424f
--- /dev/null
+++ b/board/keymile/common/common.h
@@ -0,0 +1,20 @@
+/*
+ * (C) Copyright 2008
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef __KEYMILE_COMMON_H
+#define __KEYMILE_COMMON_H
+
+int ethernet_present (void);
+int ivm_read_eeprom (void);
+
+#ifdef CONFIG_KEYMILE_HDLC_ENET
+int keymile_hdlc_enet_initialize (bd_t *bis);
+#endif
+#endif /* __KEYMILE_COMMON_H */
diff --git a/board/keymile/kmeter1/Makefile b/board/keymile/kmeter1/Makefile
new file mode 100644
index 0000000000..12a1518ff1
--- /dev/null
+++ b/board/keymile/kmeter1/Makefile
@@ -0,0 +1,53 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	+= $(BOARD).o ../common/common.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/keymile/kmeter1/config.mk b/board/keymile/kmeter1/config.mk
new file mode 100644
index 0000000000..20f298bdb9
--- /dev/null
+++ b/board/keymile/kmeter1/config.mk
@@ -0,0 +1,24 @@
+#
+# (C) Copyright 2008
+# Heiko Schocher, DENX Software Engineering, hs@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0xF0000000
diff --git a/board/keymile/kmeter1/kmeter1.c b/board/keymile/kmeter1/kmeter1.c
new file mode 100644
index 0000000000..f04a57a9cc
--- /dev/null
+++ b/board/keymile/kmeter1/kmeter1.c
@@ -0,0 +1,158 @@
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2008
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <ioports.h>
+#include <mpc83xx.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <asm/io.h>
+#include <asm/mmu.h>
+#include <pci.h>
+#include <libfdt.h>
+
+#include "../common/common.h"
+
+const qe_iop_conf_t qe_iop_conf_tab[] = {
+	/* port pin dir open_drain assign */
+
+	/* MDIO */
+	{0,  1, 3, 0, 2}, /* MDIO */
+	{0,  2, 1, 0, 1}, /* MDC */
+
+	/* UCC4 - UEC */
+	{1, 14, 1, 0, 1}, /* TxD0 */
+	{1, 15, 1, 0, 1}, /* TxD1 */
+	{1, 20, 2, 0, 1}, /* RxD0 */
+	{1, 21, 2, 0, 1}, /* RxD1 */
+	{1, 18, 1, 0, 1}, /* TX_EN */
+	{1, 26, 2, 0, 1}, /* RX_DV */
+	{1, 27, 2, 0, 1}, /* RX_ER */
+	{1, 24, 2, 0, 1}, /* COL */
+	{1, 25, 2, 0, 1}, /* CRS */
+	{2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */
+	{2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */
+
+	/* DUART - UART2 */
+	{5,  0, 1, 0, 2}, /* UART2_SOUT */
+	{5,  2, 1, 0, 1}, /* UART2_RTS */
+	{5,  3, 2, 0, 2}, /* UART2_SIN */
+	{5,  1, 2, 0, 3}, /* UART2_CTS */
+
+	/* END of table */
+	{0,  0, 0, 0, QE_IOP_TAB_END},
+};
+
+int board_early_init_r (void)
+{
+	void *reg = (void *)(CONFIG_SYS_IMMR + 0x14a8);
+	u32 val;
+
+	/*
+	 * Because of errata in the UCCs, we have to write to the reserved
+	 * registers to slow the clocks down.
+	 */
+	val = in_be32 (reg);
+	/* UCC1 */
+	val |= 0x00003000;
+	/* UCC2 */
+	val |= 0x0c000000;
+	out_be32 (reg, val);
+	/* enable the PHY on the PIGGY */
+	setbits (8, (void *)(CONFIG_SYS_PIGGY_BASE + 0x10003), 0x01);
+
+	return 0;
+}
+
+int fixed_sdram(void)
+{
+	volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+	u32 msize = 0;
+	u32 ddr_size;
+	u32 ddr_size_log2;
+
+	msize = CONFIG_SYS_DDR_SIZE;
+	for (ddr_size = msize << 20, ddr_size_log2 = 0;
+	     (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) {
+		if (ddr_size & 1)
+			return -1;
+	}
+
+	im->sysconf.ddrlaw[0].ar =
+	    LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
+
+	im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
+	im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
+	im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
+	im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
+	im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
+	im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
+	im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
+	im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
+	im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
+	im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
+	im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
+	im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL;
+	udelay (200);
+	im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+
+	return msize;
+}
+
+phys_size_t initdram (int board_type)
+{
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
+	extern void ddr_enable_ecc (unsigned int dram_size);
+#endif
+	volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+	u32 msize = 0;
+
+	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
+	msize = fixed_sdram ();
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
+	/*
+	 * Initialize DDR ECC byte
+	 */
+	ddr_enable_ecc (msize * 1024 * 1024);
+#endif
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return (msize * 1024 * 1024);
+}
+
+int checkboard (void)
+{
+	puts ("Board: Keymile kmeter1");
+	if (ethernet_present ())
+		puts (" with PIGGY.");
+	puts ("\n");
+	return 0;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup (void *blob, bd_t *bd)
+{
+	ft_cpu_setup (blob, bd);
+}
+#endif
diff --git a/board/keymile/mgcoge/mgcoge.c b/board/keymile/mgcoge/mgcoge.c
index 3683417f5c..5c50739644 100644
--- a/board/keymile/mgcoge/mgcoge.c
+++ b/board/keymile/mgcoge/mgcoge.c
@@ -25,6 +25,7 @@
 #include <mpc8260.h>
 #include <ioports.h>
 #include <malloc.h>
+#include <net.h>
 #include <asm/io.h>
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
@@ -35,7 +36,8 @@
 #include <i2c.h>
 #endif
 
-extern int ivm_read_eeprom (void);
+#include "../common/common.h"
+
 /*
  * I/O Port configuration table
  *
@@ -285,8 +287,10 @@ phys_size_t initdram (int board_type)
 
 int checkboard(void)
 {
-	puts ("Board: mgcoge\n");
-
+	puts ("Board: Keymile mgcoge");
+	if (ethernet_present ())
+		puts (" with PIGGY.");
+	puts ("\n");
 	return 0;
 }
 
diff --git a/board/keymile/mgsuvd/mgsuvd.c b/board/keymile/mgsuvd/mgsuvd.c
index 3726acf4a1..02baf622ee 100644
--- a/board/keymile/mgsuvd/mgsuvd.c
+++ b/board/keymile/mgsuvd/mgsuvd.c
@@ -22,13 +22,14 @@
  */
 #include <common.h>
 #include <mpc8xx.h>
+#include <net.h>
 #include <asm/io.h>
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
 #include <libfdt.h>
 #endif
 
-extern int ivm_read_eeprom (void);
+#include "../common/common.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -60,7 +61,10 @@ const uint sdram_table[] =
 
 int checkboard (void)
 {
-	puts ("Board: Keymile mgsuvd\n");
+	puts ("Board: Keymile mgsuvd");
+	if (ethernet_present ())
+		puts (" with PIGGY.");
+	puts ("\n");
 	return (0);
 }
 
diff --git a/board/sheldon/simpc8313/Makefile b/board/sheldon/simpc8313/Makefile
new file mode 100644
index 0000000000..7c34c5e164
--- /dev/null
+++ b/board/sheldon/simpc8313/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o sdram.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/sheldon/simpc8313/config.mk b/board/sheldon/simpc8313/config.mk
new file mode 100644
index 0000000000..ce1c0d8d93
--- /dev/null
+++ b/board/sheldon/simpc8313/config.mk
@@ -0,0 +1,13 @@
+ifndef NAND_SPL
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+endif
+
+ifndef TEXT_BASE
+TEXT_BASE = 0x00100000
+endif
+
+ifdef CONFIG_NAND_LP
+PAD_TO = 0xFFF20000
+else
+PAD_TO = 0xFFF04000
+endif
diff --git a/board/sheldon/simpc8313/sdram.c b/board/sheldon/simpc8313/sdram.c
new file mode 100644
index 0000000000..ebb70a2327
--- /dev/null
+++ b/board/sheldon/simpc8313/sdram.c
@@ -0,0 +1,193 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+#include <asm/bitops.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static long fixed_sdram(void);
+
+#if defined(CONFIG_NAND_SPL)
+void si_wait_i2c(void)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+
+	while (!(__raw_readb(&im->i2c[0].sr) & 0x02))
+		;
+
+	__raw_writeb(0x00, &im->i2c[0].sr);
+
+	sync();
+
+	return;
+}
+
+void si_read_i2c(u32 lbyte, int count, u8 *buffer)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	u32 i;
+	u8 chip = 0x50 << 1; /* boot sequencer I2C */
+	u32 ubyte = (lbyte & 0xff00) >> 8;
+
+	lbyte &= 0xff;
+
+	/*
+	 * Set up controller
+	 */
+	__raw_writeb(0x3f, &im->i2c[0].fdr);
+	__raw_writeb(0x00, &im->i2c[0].adr);
+	__raw_writeb(0x00, &im->i2c[0].sr);
+	__raw_writeb(0x00, &im->i2c[0].dr);
+
+	while (__raw_readb(&im->i2c[0].sr) & 0x20)
+		;
+
+	/*
+	 * Writing address to device
+	 */
+	__raw_writeb(0xb0, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(chip, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xb0, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(ubyte, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(lbyte, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xb4, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(chip + 1, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xa0, &im->i2c[0].cr);
+	sync();
+
+	/*
+	 * Dummy read
+	 */
+	__raw_readb(&im->i2c[0].dr);
+
+	si_wait_i2c();
+
+	/*
+	 * Read actual data
+	 */
+	for (i = 0; i < count; i++)
+	{
+		if (i == (count - 2))	/* Reached next to last byte, No ACK */
+			__raw_writeb(0xa8, &im->i2c[0].cr);
+		if (i == (count - 1))	/* Reached last byte, STOP */
+			__raw_writeb(0x88, &im->i2c[0].cr);
+
+		/* Read byte of data */
+		buffer[i] = __raw_readb(&im->i2c[0].dr);
+
+		if (i == (count - 1))
+			break;
+		si_wait_i2c();
+	}
+
+	return;
+}
+#endif /* CONFIG_NAND_SPL */
+
+phys_size_t initdram(int board_type)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	volatile fsl_lbus_t *lbc= &im->lbus;
+	u32 msize;
+
+	if ((__raw_readl(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32) im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	__raw_writel(CONFIG_SYS_DDR_BASE & LAWBAR_BAR, &im->sysconf.ddrlaw[0].bar);
+
+	msize = fixed_sdram();
+
+	/* Local Bus setup lbcr and mrtpr */
+	__raw_writel(CONFIG_SYS_LBC_LBCR, &lbc->lbcr);
+	__raw_writel(CONFIG_SYS_LBC_MRTPR, &lbc->mrtpr);
+	sync();
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return (msize * 1024 * 1024);
+}
+
+/*************************************************************************
+ *  fixed sdram init -- reads values from boot sequencer I2C
+ ************************************************************************/
+static long fixed_sdram(void)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	u32 msizelog2, msize = 1;
+#if defined(CONFIG_NAND_SPL)
+	u32 i;
+	const u8 bytecount = 135;
+	u8 buffer[bytecount];
+	u32 addr, data;
+
+	si_read_i2c(0, bytecount, buffer);
+
+	for (i = 18; i < bytecount; i += 7){
+		addr = (u32)buffer[i];
+		addr <<= 8;
+		addr |= (u32)buffer[i + 1];
+		addr <<= 2;
+		data = (u32)buffer[i + 2];
+		data <<= 8;
+		data |= (u32)buffer[i + 3];
+		data <<= 8;
+		data |= (u32)buffer[i + 4];
+		data <<= 8;
+		data |= (u32)buffer[i + 5];
+
+		__raw_writel(data, (u32 *)(CONFIG_SYS_IMMR + addr));
+	}
+
+	sync();
+
+	/* enable DDR controller */
+	__raw_writel((__raw_readl(&im->ddr.sdram_cfg) | SDRAM_CFG_MEM_EN), &im->ddr.sdram_cfg);
+#endif /* (CONFIG_NAND_SPL) */
+
+	msizelog2 = ((__raw_readl(&im->sysconf.ddrlaw[0].ar) & LAWAR_SIZE) + 1);
+	msize <<= (msizelog2 - 20);
+
+	return msize;
+}
diff --git a/board/sheldon/simpc8313/simpc8313.c b/board/sheldon/simpc8313/simpc8313.c
new file mode 100644
index 0000000000..25e5c2409d
--- /dev/null
+++ b/board/sheldon/simpc8313/simpc8313.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	puts("Board: Sheldon Instruments SIMPC8313\n");
+	return 0;
+}
+
+#ifndef CONFIG_NAND_SPL
+static struct pci_region pci_regions[] = {
+	{
+		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+		size: CONFIG_SYS_PCI1_MEM_SIZE,
+		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+		size: CONFIG_SYS_PCI1_MMIO_SIZE,
+		flags: PCI_REGION_MEM
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_IO_BASE,
+		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+		size: CONFIG_SYS_PCI1_IO_SIZE,
+		flags: PCI_REGION_IO
+	}
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions };
+	int warmboot;
+
+	/* Enable all 3 PCI_CLK_OUTPUTs. */
+	clk->occr |= 0xe0000000;
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
+	pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+	pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
+	pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+	warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+
+	mpc83xx_pci_init(1, reg, warmboot);
+}
+
+/*
+ * Miscellaneous late-boot configurations
+ */
+int misc_init_r(void)
+{
+	int rc = 0;
+
+	return rc;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+}
+#endif
+#else /* CONFIG_NAND_SPL */
+void board_init_f(ulong bootflag)
+{
+	NS16550_init((NS16550_t)(CONFIG_SYS_IMMR + 0x4500),
+				CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
+	puts("NAND boot... ");
+	init_timebase();
+	initdram(0);
+	relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000, (gd_t *)gd,
+				  CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (gd->flags & GD_FLG_SILENT)
+		return;
+
+	if (c == '\n')
+		NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), '\r');
+
+	NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), c);
+}
+#endif