summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
authorLokesh Vutla <lokeshvutla@ti.com>2016-05-16 11:47:26 +0530
committerTom Rini <trini@konsulko.com>2016-05-27 15:47:52 -0400
commit97f3a178b2a3d5a7767cb6cb15ba9c40ba804ebb (patch)
tree006195ca5c4c6e7ec9f52d7a2426e07bcc1aa053 /board
parent3164f3c68941a1665090bca903d56754ac36f89d (diff)
board: AM335x-ICEv2: Add cpsw support
In order to enable cpsw on AM335x ICEv2 board, the following needs to be done: 1)There are few on board jumper settings which gives a choice between cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting this, there are few GPIOs which control these muxes that needs to be held high. 2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected via I2C. This needs to properly programmed and locked for PHY operation. And PHY needs to be reset before before being used, which is also held by a GPIO. 3) RMII mode needs to be selected. [1] http://www.ti.com/lit/zip/tidr336 [2] http://www.ti.com/lit/ds/symlink/cdce913.pdf Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Diffstat (limited to 'board')
-rw-r--r--board/ti/am335x/board.c87
1 files changed, 80 insertions, 7 deletions
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 51c43587c3..8f4769206d 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -16,6 +16,7 @@
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
+#include <asm/arch/clk_synthesizer.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
@@ -37,8 +38,13 @@
DECLARE_GLOBAL_DATA_PTR;
/* GPIO that controls power to DDR on EVM-SK */
-#define GPIO_DDR_VTT_EN 7
-#define ICE_GPIO_DDR_VTT_EN 18
+#define GPIO_TO_PIN(bank, gpio) (32 * (bank) + (gpio))
+#define GPIO_DDR_VTT_EN GPIO_TO_PIN(0, 7)
+#define ICE_GPIO_DDR_VTT_EN GPIO_TO_PIN(0, 18)
+#define GPIO_PR1_MII_CTRL GPIO_TO_PIN(3, 4)
+#define GPIO_MUX_MII_CTRL GPIO_TO_PIN(3, 10)
+#define GPIO_FET_SWITCH_CTRL GPIO_TO_PIN(0, 7)
+#define GPIO_PHY_RESET GPIO_TO_PIN(2, 5)
#if defined(CONFIG_SPL_BUILD) || \
(defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_DM_ETH))
@@ -474,6 +480,49 @@ void sdram_init(void)
}
#endif
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void request_and_set_gpio(int gpio, char *name)
+{
+ int ret;
+
+ ret = gpio_request(gpio, name);
+ if (ret < 0) {
+ printf("%s: Unable to request %s\n", __func__, name);
+ return;
+ }
+
+ ret = gpio_direction_output(gpio, 0);
+ if (ret < 0) {
+ printf("%s: Unable to set %s as output\n", __func__, name);
+ goto err_free_gpio;
+ }
+
+ gpio_set_value(gpio, 1);
+
+ return;
+
+err_free_gpio:
+ gpio_free(gpio);
+}
+
+#define REQUEST_AND_SET_GPIO(N) request_and_set_gpio(N, #N);
+
+/**
+ * RMII mode on ICEv2 board needs 50MHz clock. Given the clock
+ * synthesizer With a capacitor of 18pF, and 25MHz input clock cycle
+ * PLL1 gives an output of 100MHz. So, configuring the div2/3 as 2 to
+ * give 50MHz output for Eth0 and 1.
+ */
+static struct clk_synth cdce913_data = {
+ .id = 0x81,
+ .capacitor = 0x90,
+ .mux = 0x6d,
+ .pdiv2 = 0x2,
+ .pdiv3 = 0x2,
+};
+#endif
+
/*
* Basic board specific setup. Pinmux has been handled already.
*/
@@ -487,6 +536,23 @@ int board_init(void)
#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
gpmc_init();
#endif
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD))
+ int rv;
+
+ if (board_is_icev2()) {
+ REQUEST_AND_SET_GPIO(GPIO_PR1_MII_CTRL);
+ REQUEST_AND_SET_GPIO(GPIO_MUX_MII_CTRL);
+ REQUEST_AND_SET_GPIO(GPIO_FET_SWITCH_CTRL);
+ REQUEST_AND_SET_GPIO(GPIO_PHY_RESET);
+
+ rv = setup_clock_synthesizer(&cdce913_data);
+ if (rv) {
+ printf("Clock synthesizer setup failed %d\n", rv);
+ return rv;
+ }
+ }
+#endif
+
return 0;
}
@@ -554,6 +620,12 @@ static struct cpsw_platform_data cpsw_data = {
};
#endif
+#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) &&\
+ defined(CONFIG_SPL_BUILD)) || \
+ ((defined(CONFIG_DRIVER_TI_CPSW) || \
+ defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
+ !defined(CONFIG_SPL_BUILD))
+
/*
* This function will:
* Read the eFuse for MAC addresses, and set ethaddr/eth1addr/usbnet_devaddr
@@ -565,11 +637,6 @@ static struct cpsw_platform_data cpsw_data = {
* Build in only these cases to avoid warnings about unused variables
* when we build an SPL that has neither option but full U-Boot will.
*/
-#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) \
- && defined(CONFIG_SPL_BUILD)) || \
- ((defined(CONFIG_DRIVER_TI_CPSW) || \
- defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \
- !defined(CONFIG_SPL_BUILD))
int board_eth_init(bd_t *bis)
{
int rv, n = 0;
@@ -620,6 +687,12 @@ int board_eth_init(bd_t *bis)
writel(MII_MODE_ENABLE, &cdev->miisel);
cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
PHY_INTERFACE_MODE_MII;
+ } else if (board_is_icev2()) {
+ writel(RMII_MODE_ENABLE | RMII_CHIPCKL_ENABLE, &cdev->miisel);
+ cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RMII;
+ cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RMII;
+ cpsw_slaves[0].phy_addr = 1;
+ cpsw_slaves[1].phy_addr = 3;
} else {
writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel);
cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =