ARM: davinci: remove hawkboard support

This is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

7 files changed, 0 insertions, 307 deletions

diff --git a/board/davinci/da8xxevm/Kconfig b/board/davinci/da8xxevm/Kconfig
index 1a841ce6e0..1108e4b164 100644
--- a/board/davinci/da8xxevm/Kconfig
+++ b/board/davinci/da8xxevm/Kconfig
@@ -23,16 +23,3 @@ config SYS_CONFIG_NAME
 	default "da850evm"
 
 endif
-
-if TARGET_HAWKBOARD
-
-config SYS_BOARD
-	default "da8xxevm"
-
-config SYS_VENDOR
-	default "davinci"
-
-config SYS_CONFIG_NAME
-	default "hawkboard"
-
-endif
diff --git a/board/davinci/da8xxevm/MAINTAINERS b/board/davinci/da8xxevm/MAINTAINERS
index dd66f07e72..10c4e2ffc0 100644
--- a/board/davinci/da8xxevm/MAINTAINERS
+++ b/board/davinci/da8xxevm/MAINTAINERS
@@ -12,11 +12,3 @@ F:	include/configs/da850evm.h
 F:	configs/da850_am18xxevm_defconfig
 F:	configs/da850evm_defconfig
 F:	configs/da850evm_direct_nor_defconfig
-
-HAWKBOARD BOARD
-M:	Syed Mohammed Khasim <sm.khasim@gmail.com>
-M:	Sughosh Ganu <urwithsughosh@gmail.com>
-S:	Maintained
-F:	include/configs/hawkboard.h
-F:	configs/hawkboard_defconfig
-F:	configs/hawkboard_uart_defconfig
diff --git a/board/davinci/da8xxevm/Makefile b/board/davinci/da8xxevm/Makefile
index d3acacc33d..4da509b5e1 100644
--- a/board/davinci/da8xxevm/Makefile
+++ b/board/davinci/da8xxevm/Makefile
@@ -9,4 +9,3 @@
 
 obj-$(CONFIG_MACH_DAVINCI_DA830_EVM)	+= da830evm.o
 obj-$(CONFIG_MACH_DAVINCI_DA850_EVM)	+= da850evm.o
-obj-$(CONFIG_MACH_DAVINCI_HAWK)		+= hawkboard.o
diff --git a/board/davinci/da8xxevm/README.hawkboard b/board/davinci/da8xxevm/README.hawkboard
deleted file mode 100644
index d6ae02ec02..0000000000
--- a/board/davinci/da8xxevm/README.hawkboard
+++ /dev/null
@@ -1,92 +0,0 @@
-Summary
-=======
-The README is for the boot procedure used for TI's OMAP-L138 based
-hawkboard. The hawkboard comes with a 128MiB Nand flash and a 128MiB
-DDR SDRAM along with a host of other controllers.
-
-The hawkboard is booted in three stages. The initial bootloader which
-executes upon reset is the Rom Boot Loader(RBL) which sits in the
-internal ROM of the omap. The RBL initialises the memory and the nand
-controller, and copies the image stored at a predefined location(block
-1) of the nand flash. The image loaded by the RBL to the memory is the
-AIS signed spl image. This, in turns copies the u-boot binary from the
-nand flash to the memory and jumps to the u-boot entry point.
-
-AIS is an image format defined by TI for the images that are to be
-loaded to memory by the RBL. The image is divided into a series of
-sections and the image's entry point is specified. Each section comes
-with meta data like the target address the section is to be copied to
-and the size of the section, which is used by the RBL to load the
-image. At the end of the image the RBL jumps to the image entry
-point.
-
-The secondary stage bootloader(spl) which is loaded by the RBL then
-loads the u-boot from a predefined location in the nand to the memory
-and jumps to the u-boot entry point.
-
-The reason a secondary stage bootloader is used is because the ECC
-layout expected by the RBL is not the same as that used by
-u-boot/linux. This also implies that for flashing the spl image,we
-need to use the u-boot which uses the ECC layout expected by the
-RBL[1]. Booting u-boot over UART(UART boot) is explained here[2].
-
-
-Compilation
-===========
-Three images might be needed
-
-* spl - This is the secondary bootloader which boots the u-boot
-  binary.
-
-* u-boot binary - This is the image flashed to the nand and copied to
-  the memory by the spl.
-
-  Both the images get compiled with hawkboard_config, with the TOPDIR
-  containing the u-boot images, and the spl image under the spl
-  directory.
-
-  The spl image needs to be processed with the AISGen tool for
-  generating the AIS signed image to be flashed. Steps for generating
-  the AIS image are explained here[3].
-
-* u-boot for uart boot - This is same as the u-boot binary generated
-  above, with the sole difference of the CONFIG_SYS_TEXT_BASE being
-  0xc1080000, as expected by the RBL.
-
-  hawkboard_uart_config
-
-
-Flashing the images to Nand
-===========================
-The spl AIS image needs to be flashed to the block 1 of the Nand
-flash, as that is the location the RBL expects the image[4]. For
-flashing the spl, boot over the u-boot specified in [1], and flash the
-image
-
-=> tftpboot 0xc0700000 <nand_spl_ais.bin>
-=> nand erase 0x20000 0x20000
-=> nand write.e 0xc0700000 0x20000 <nand_spl_size>
-
-The u-boot binary is flashed at location 0xe0000(block 6) of the nand
-flash. The spl loader expects the u-boot at this location. For
-flashing the u-boot binary
-
-=> tftpboot 0xc0700000 u-boot.bin
-=> nand erase 0xe0000 0x40000
-=> nand write.e 0xc0700000 0xe0000 <u-boot-size>
-
-
-Links
-=====
-
-[1]
- http://code.google.com/p/hawkboard/downloads/detail?name=u-boot_uart_ais_v1.bin
-
-[2]
- http://elinux.org/Hawkboard#Booting_u-boot_over_UART
-
-[3]
- http://elinux.org/Hawkboard#Signing_u-boot_for_UART_boot
-
-[4]
- http://processors.wiki.ti.com/index.php/RBL_UBL_and_host_program#RBL_booting_from_NAND_and_ECC.2FBad_blocks
diff --git a/board/davinci/da8xxevm/hawkboard-ais-nand.cfg b/board/davinci/da8xxevm/hawkboard-ais-nand.cfg
deleted file mode 100644
index 2b12b6c08a..0000000000
--- a/board/davinci/da8xxevm/hawkboard-ais-nand.cfg
+++ /dev/null
@@ -1,4 +0,0 @@
-#	PLL0CFG0	PLL0CFG1
-PLL0	0x00180001	0x00000205
-#	PLL1CFG0	PLL1CFG1	DRPYC1R		SDCR		SDTIMR1		SDTIMR2		SDRCR		CLK2XSRC
-DDR2	0x15010001	0x00000002	0x00000043	0x00134632	0x26492a09	0x7d13c722	0x00000249	0x00000000
diff --git a/board/davinci/da8xxevm/hawkboard.c b/board/davinci/da8xxevm/hawkboard.c
deleted file mode 100644
index d5992a5564..0000000000
--- a/board/davinci/da8xxevm/hawkboard.c
+++ /dev/null
@@ -1,120 +0,0 @@
-/*
- * Modified for Hawkboard - Syed Mohammed Khasim <khasim@beagleboard.org>
- *
- * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc.  <nsekhar@ti.com>
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- * Copyright (C) 2004 Texas Instruments.
- * Copyright (C) 2012 Sughosh Ganu <urwithsughosh@gmail.com>.
- *
- * ----------------------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- * ----------------------------------------------------------------------------
- */
-
-#include <common.h>
-#include <asm/errno.h>
-#include <asm/arch/hardware.h>
-#include <asm/io.h>
-#include <asm/arch/davinci_misc.h>
-#include <asm/arch/pinmux_defs.h>
-#include <asm/arch/da8xx-usb.h>
-#include <ns16550.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const struct pinmux_resource pinmuxes[] = {
-	PINMUX_ITEM(emac_pins_mii),
-	PINMUX_ITEM(emac_pins_mdio),
-	PINMUX_ITEM(emifa_pins_cs3),
-	PINMUX_ITEM(emifa_pins_cs4),
-	PINMUX_ITEM(emifa_pins_nand),
-	PINMUX_ITEM(uart2_pins_txrx),
-	PINMUX_ITEM(uart2_pins_rtscts),
-};
-
-const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
-
-const struct lpsc_resource lpsc[] = {
-	{ DAVINCI_LPSC_AEMIF },	/* NAND, NOR */
-	{ DAVINCI_LPSC_SPI1 },	/* Serial Flash */
-	{ DAVINCI_LPSC_EMAC },	/* image download */
-	{ DAVINCI_LPSC_UART2 },	/* console */
-	{ DAVINCI_LPSC_GPIO },
-};
-
-const int lpsc_size = ARRAY_SIZE(lpsc);
-
-int board_init(void)
-{
-	/* arch number of the board */
-	gd->bd->bi_arch_number = MACH_TYPE_OMAPL138_HAWKBOARD;
-
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
-	return 0;
-}
-
-int board_early_init_f(void)
-{
-	/*
-	 * Kick Registers need to be set to allow access to Pin Mux registers
-	 */
-	writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0);
-	writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1);
-
-	/* set cfgchip3 to select mii */
-	writel(readl(&davinci_syscfg_regs->cfgchip3) &
-	       ~(1 << 8), &davinci_syscfg_regs->cfgchip3);
-
-	return 0;
-}
-
-int misc_init_r(void)
-{
-	char buf[32];
-
-	printf("ARM Clock : %s MHz\n",
-	       strmhz(buf, clk_get(DAVINCI_ARM_CLKID)));
-
-	return 0;
-}
-
-int usb_phy_on(void)
-{
-	u32 timeout;
-	u32 cfgchip2;
-
-	cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
-
-	cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN |
-		      CFGCHIP2_OTGMODE | CFGCHIP2_REFFREQ |
-		      CFGCHIP2_USB1PHYCLKMUX);
-	cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN | CFGCHIP2_PHY_PLLON |
-		    CFGCHIP2_REFFREQ_24MHZ | CFGCHIP2_USB2PHYCLKMUX |
-		    CFGCHIP2_USB1SUSPENDM;
-
-	writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
-
-	/* wait until the usb phy pll locks */
-	timeout = DA8XX_USB_OTG_TIMEOUT;
-	while (timeout--)
-		if (readl(&davinci_syscfg_regs->cfgchip2) & CFGCHIP2_PHYCLKGD)
-			return 1;
-
-	/* USB phy was not turned on */
-	return 0;
-}
-
-void usb_phy_off(void)
-{
-	u32 cfgchip2;
-
-	/*
-	 * Power down the on-chip PHY.
-	 */
-	cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
-	cfgchip2 &= ~(CFGCHIP2_PHY_PLLON | CFGCHIP2_USB1SUSPENDM);
-	cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN | CFGCHIP2_RESET;
-	writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
-}
diff --git a/board/davinci/da8xxevm/u-boot-spl-hawk.lds b/board/davinci/da8xxevm/u-boot-spl-hawk.lds
deleted file mode 100644
index 5c629db139..0000000000
--- a/board/davinci/da8xxevm/u-boot-spl-hawk.lds
+++ /dev/null
@@ -1,69 +0,0 @@
-/*
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
-	. = 0xc1080000;
-
-	. = ALIGN(4);
-	.text      :
-	{
-	  *(.vectors)
-	  arch/arm/cpu/arm926ejs/start.o		(.text*)
-	  arch/arm/cpu/arm926ejs/built-in.o		(.text*)
-	  drivers/mtd/nand/built-in.o			(.text*)
-
-	  *(.text*)
-	}
-
-	. = ALIGN(4);
-	.rodata : { *(.rodata*) }
-
-	. = ALIGN(4);
-	.data : {
-		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
-	}
-
-	. = ALIGN(4);
-	__image_copy_end = .;
-	__rel_dyn_start = .;
-	__rel_dyn_end = .;
-
-	__got_start = .;
-	. = ALIGN(4);
-	.got : { *(.got) }
-
-	__got_end = .;
-
-	.bss :
-	{
-		. = ALIGN(4);
-		__bss_start = .;
-		*(.bss*)
-		. = ALIGN(4);
-		__bss_end = .;
-	}
-
-	.end :
-	{
-		*(.__end)
-	}
-}