OMAP3 Move cache routine to cache.S

v7_flush_dcache_all, because it depends on omap ROM code is not
generic.  Rename the function to 'invalidate_dcache' and move it
to the omap cpu directory.

Collect the other omap cache routines l2_cache_enable and
l2_cache_disable with invalide_dcache into cache.S.  This
means removing the old cache.c file that contained l2_cache_enable
and l2_cache_disable.

The conversion from cache.c to cache.S was done most through
disassembling the uboot binary.  The only significant change was
to change the comparision for the return of get_cpu_rev from

   cmp	r0, #0
   beq	earlier_than_label

Which was lost information to

   cmp	r0, #CPU_3XX_ES20
   blt	earlier_than_label

The paths through the enable routine were verified by
adding an infinite loop and seeing the hang.  Then
removing the infinite loop and seeing it continue.

The disable routine is similar enough that it was not
tested with this method.

Run tested by cold booting from nand on beagle and zoom1.
Compile tested on MAKEALL arm.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>

1 files changed, 0 insertions, 85 deletions

diff --git a/cpu/arm_cortexa8/start.S b/cpu/arm_cortexa8/start.S
index 6bd65521bd..14a9bd3b03 100644
--- a/cpu/arm_cortexa8/start.S
+++ b/cpu/arm_cortexa8/start.S
@@ -415,88 +415,3 @@ fiq:
 
 #endif
 
-/*
- *	v7_flush_dcache_all()
- *
- *	Flush the whole D-cache.
- *
- *	Corrupted registers: r0-r5, r7, r9-r11
- *
- *	- mm	- mm_struct describing address space
- */
-	.align 5
-.global v7_flush_dcache_all
-v7_flush_dcache_all:
-	stmfd	r13!, {r0 - r5, r7, r9 - r12, r14}
-
-	mov	r7, r0				@ take a backup of device type
-	cmp	r0, #0x3			@ check if the device type is
-						@ GP
-	moveq r12, #0x1				@ set up to invalide L2
-smi:	.word 0x01600070			@ Call SMI monitor (smieq)
-	cmp	r7, #0x3			@ compare again in case its
-						@ lost
-	beq	finished_inval			@ if GP device, inval done
-						@ above
-
-	mrc	p15, 1, r0, c0, c0, 1		@ read clidr
-	ands	r3, r0, #0x7000000		@ extract loc from clidr
-	mov	r3, r3, lsr #23			@ left align loc bit field
-	beq	finished_inval			@ if loc is 0, then no need to
-						@ clean
-	mov	r10, #0				@ start clean at cache level 0
-inval_loop1:
-	add	r2, r10, r10, lsr #1		@ work out 3x current cache
-						@ level
-	mov	r1, r0, lsr r2			@ extract cache type bits from
-						@ clidr
-	and	r1, r1, #7			@ mask of the bits for current
-						@ cache only
-	cmp	r1, #2				@ see what cache we have at
-						@ this level
-	blt	skip_inval			@ skip if no cache, or just
-						@ i-cache
-	mcr	p15, 2, r10, c0, c0, 0		@ select current cache level
-						@ in cssr
-	mov	r2, #0				@ operand for mcr SBZ
-	mcr	p15, 0, r2, c7, c5, 4		@ flush prefetch buffer to
-						@ sych the new cssr&csidr,
-						@ with armv7 this is 'isb',
-						@ but we compile with armv5
-	mrc	p15, 1, r1, c0, c0, 0		@ read the new csidr
-	and	r2, r1, #7			@ extract the length of the
-						@ cache lines
-	add	r2, r2, #4			@ add 4 (line length offset)
-	ldr	r4, =0x3ff
-	ands	r4, r4, r1, lsr #3		@ find maximum number on the
-						@ way size
-	clz	r5, r4				@ find bit position of way
-						@ size increment
-	ldr	r7, =0x7fff
-	ands	r7, r7, r1, lsr #13		@ extract max number of the
-						@ index size
-inval_loop2:
-	mov	r9, r4				@ create working copy of max
-						@ way size
-inval_loop3:
-	orr	r11, r10, r9, lsl r5		@ factor way and cache number
-						@ into r11
-	orr	r11, r11, r7, lsl r2		@ factor index number into r11
-	mcr	p15, 0, r11, c7, c6, 2		@ invalidate by set/way
-	subs	r9, r9, #1			@ decrement the way
-	bge	inval_loop3
-	subs	r7, r7, #1			@ decrement the index
-	bge	inval_loop2
-skip_inval:
-	add	r10, r10, #2			@ increment cache number
-	cmp	r3, r10
-	bgt	inval_loop1
-finished_inval:
-	mov	r10, #0				@ swith back to cache level 0
-	mcr	p15, 2, r10, c0, c0, 0		@ select current cache level
-						@ in cssr
-	mcr	p15, 0, r10, c7, c5, 4		@ flush prefetch buffer,
-						@ with armv7 this is 'isb',
-						@ but we compile with armv5
-
-	ldmfd	r13!, {r0 - r5, r7, r9 - r12, pc}