[Blackfin][PATCH] code cleanup

1 files changed, 80 insertions, 81 deletions

diff --git a/cpu/bf533/init_sdram.S b/cpu/bf533/init_sdram.S
index d92c877f59..1aae9e30f9 100644
--- a/cpu/bf533/init_sdram.S
+++ b/cpu/bf533/init_sdram.S
@@ -28,17 +28,17 @@ init_sdram:
 	[--SP] = (R7:0);
 	[--SP] = (P5:0);
 
-#if (BFIN_BOOT_MODE == BF533_SPI_BOOT) 
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
 	p0.h = hi(SPI_BAUD);
 	p0.l = lo(SPI_BAUD);
 	r0.l = CONFIG_SPI_BAUD;
 	w[p0] = r0.l;
-    SSYNC;
+	SSYNC;
 #endif
 
 	/*
-         * PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
-         */
+	 * PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
+	 */
 	p0.h = hi(PLL_LOCKCNT);
 	p0.l = lo(PLL_LOCKCNT);
 	r0 = 0x300(Z);
@@ -46,43 +46,43 @@ init_sdram:
 	ssync;
 
 	/*
-         * Put SDRAM in self-refresh, incase anything is running
-         */
-        P2.H = hi(EBIU_SDGCTL);
-        P2.L = lo(EBIU_SDGCTL);
-        R0 = [P2];
-        BITSET (R0, 24);
-        [P2] = R0;
-        SSYNC;
-
-        /*
-         *  Set PLL_CTL with the value that we calculate in R0
-         *   - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
-         *   - [8]     = BYPASS    : BYPASS the PLL, run CLKIN into CCLK/SCLK
-         *   - [7]     = output delay (add 200ps of delay to mem signals)
-         *   - [6]     = input delay (add 200ps of input delay to mem signals)
-         *   - [5]     = PDWN      : 1=All Clocks off
-         *   - [3]     = STOPCK    : 1=Core Clock off
-         *   - [1]     = PLL_OFF   : 1=Disable Power to PLL
-         *   - [0]     = DF        : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
-         *   all other bits set to zero
-         */
-
-        r0 = CONFIG_VCO_MULT & 63;      /* Load the VCO multiplier         */
-        r0 = r0 << 9;                   /* Shift it over,                  */
-        r1 = CONFIG_CLKIN_HALF;        /* Do we need to divide CLKIN by 2?*/
-        r0 = r1 | r0;
-        r1 = CONFIG_PLL_BYPASS;         /* Bypass the PLL?                 */
-        r1 = r1 << 8;                   /* Shift it over                   */
-        r0 = r1 | r0;                   /* add them all together           */
-
-        p0.h = hi(PLL_CTL);
-        p0.l = lo(PLL_CTL);             /* Load the address                */
-        cli r2;                         /* Disable interrupts              */
+	 * Put SDRAM in self-refresh, incase anything is running
+	 */
+	P2.H = hi(EBIU_SDGCTL);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITSET (R0, 24);
+	[P2] = R0;
+	SSYNC;
+
+	/*
+	 *  Set PLL_CTL with the value that we calculate in R0
+	 *   - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+	 *   - [8]     = BYPASS    : BYPASS the PLL, run CLKIN into CCLK/SCLK
+	 *   - [7]     = output delay (add 200ps of delay to mem signals)
+	 *   - [6]     = input delay (add 200ps of input delay to mem signals)
+	 *   - [5]     = PDWN      : 1=All Clocks off
+	 *   - [3]     = STOPCK    : 1=Core Clock off
+	 *   - [1]     = PLL_OFF   : 1=Disable Power to PLL
+	 *   - [0]     = DF        : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+	 *   all other bits set to zero
+	 */
+
+	r0 = CONFIG_VCO_MULT & 63;	/* Load the VCO multiplier         */
+	r0 = r0 << 9;			/* Shift it over,                  */
+	r1 = CONFIG_CLKIN_HALF;		/* Do we need to divide CLKIN by 2?*/
+	r0 = r1 | r0;
+	r1 = CONFIG_PLL_BYPASS;		/* Bypass the PLL?                 */
+	r1 = r1 << 8;			/* Shift it over                   */
+	r0 = r1 | r0;			/* add them all together           */
+
+	p0.h = hi(PLL_CTL);
+	p0.l = lo(PLL_CTL);		/* Load the address                */
+	cli r2;				/* Disable interrupts              */
 	ssync;
-        w[p0] = r0.l;                   /* Set the value                   */
-        idle;                           /* Wait for the PLL to stablize    */
-        sti r2;                         /* Enable interrupts               */
+	w[p0] = r0.l;			/* Set the value                   */
+	idle;				/* Wait for the PLL to stablize    */
+	sti r2;				/* Enable interrupts               */
 
 check_again:
 	p0.h = hi(PLL_STAT);
@@ -92,46 +92,46 @@ check_again:
 	if ! CC jump check_again;
 
 	/* Configure SCLK & CCLK Dividers */
-       	r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
-        p0.h = hi(PLL_DIV);
-        p0.l = lo(PLL_DIV);
-        w[p0] = r0.l;
-        ssync;
+	r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+	p0.h = hi(PLL_DIV);
+	p0.l = lo(PLL_DIV);
+	w[p0] = r0.l;
+	ssync;
 
 	/*
-         * We now are running at speed, time to set the Async mem bank wait states
+	 * We now are running at speed, time to set the Async mem bank wait states
 	 * This will speed up execution, since we are normally running from FLASH.
 	 */
 
-        p2.h = (EBIU_AMBCTL1 >> 16);
-        p2.l = (EBIU_AMBCTL1 & 0xFFFF);
-        r0.h = (AMBCTL1VAL >> 16);
-        r0.l = (AMBCTL1VAL & 0xFFFF);
-        [p2] = r0;
-        ssync;
-
-        p2.h = (EBIU_AMBCTL0 >> 16);
-        p2.l = (EBIU_AMBCTL0 & 0xFFFF);
-        r0.h = (AMBCTL0VAL >> 16);
-        r0.l = (AMBCTL0VAL & 0xFFFF);
-        [p2] = r0;
-        ssync;
-
-        p2.h = (EBIU_AMGCTL >> 16);
-        p2.l = (EBIU_AMGCTL & 0xffff);
-        r0 = AMGCTLVAL;
-        w[p2] = r0;
-        ssync;
+	p2.h = (EBIU_AMBCTL1 >> 16);
+	p2.l = (EBIU_AMBCTL1 & 0xFFFF);
+	r0.h = (AMBCTL1VAL >> 16);
+	r0.l = (AMBCTL1VAL & 0xFFFF);
+	[p2] = r0;
+	ssync;
+	
+	p2.h = (EBIU_AMBCTL0 >> 16);
+	p2.l = (EBIU_AMBCTL0 & 0xFFFF);
+	r0.h = (AMBCTL0VAL >> 16);
+	r0.l = (AMBCTL0VAL & 0xFFFF);
+	[p2] = r0;
+	ssync;
+	
+	p2.h = (EBIU_AMGCTL >> 16);
+	p2.l = (EBIU_AMGCTL & 0xffff);
+	r0 = AMGCTLVAL;
+	w[p2] = r0;
+	ssync;
 
 	/*
 	 * Now, Initialize the SDRAM,
 	 * start with the SDRAM Refresh Rate Control Register
-         */
+	 */
 	p0.l = lo(EBIU_SDRRC);
-        p0.h = hi(EBIU_SDRRC);
-        r0 = mem_SDRRC;
-        w[p0] = r0.l;
-        ssync;
+	p0.h = hi(EBIU_SDRRC);
+	r0 = mem_SDRRC;
+	w[p0] = r0.l;
+	ssync;
 
 	/*
 	 * SDRAM Memory Bank Control Register - bank specific parameters
@@ -147,29 +147,29 @@ check_again:
 	 * Disable self-refresh
 	 */
 	P2.H = hi(EBIU_SDGCTL);
-        P2.L = lo(EBIU_SDGCTL);
-        R0 = [P2];
-        BITCLR (R0, 24);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITCLR (R0, 24);
 
 	/*
-         * Check if SDRAM is already powered up, if it is, enable self-refresh
-         */
+	 * Check if SDRAM is already powered up, if it is, enable self-refresh
+	 */
 	p0.h = hi(EBIU_SDSTAT);
 	p0.l = lo(EBIU_SDSTAT);
 	r2.l = w[p0];
 	cc = bittst(r2,3);
 	if !cc jump skip;
-    	NOP;
+	NOP;
 	BITSET (R0, 23);
 skip:
 	[P2] = R0;
-        SSYNC;
+	SSYNC;
 
 	/* Write in the new value in the register */
-        R0.L = lo(mem_SDGCTL);
-        R0.H = hi(mem_SDGCTL);
+	R0.L = lo(mem_SDGCTL);
+	R0.H = hi(mem_SDGCTL);
 	[P2] = R0;
-        SSYNC;
+	SSYNC;
 	nop;
 
 	(P5:0) = [SP++];
@@ -177,4 +177,3 @@ skip:
 	RETS   = [SP++];
 	ASTAT  = [SP++];
 	RTS;
-