Merge branch 'next' of git://git.denx.de/u-boot

* 'next' of git://git.denx.de/u-boot:
  MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
  doc: cleanup - move board READMEs into respective board directories
  net: sh_eth: add support for SH7757's GETHER
  net: sh_eth: modify the definitions of regsiter
  net: sh_eth: add SH_ETH_TYPE_ condition
  net: sh_eth: clean up for the SH7757's code
  net: fec_mxc: Fix MDC for xMII
  net: fec_mxc: Fix setting of RCR for xMII
  net: nfs: make NFS_TIMEOUT configurable
  net: Inline the new eth_setenv_enetaddr_by_index function
  net: allow setting env enetaddr from net device setting
  net/designware: Consecutive writes to the same register to be avoided
  CACHE: net: asix: Fix asix driver to work with data cache on
  net: phy: micrel: make ksz9021 phy accessible
  net: abort network initialization if the PHY driver fails
  phylib: phy_startup() should return an error code on failure
  net: tftp: fix type of block arg to store_block

Signed-off-by: Wolfgang Denk <wd@denx.de>

1 files changed, 0 insertions, 163 deletions

diff --git a/doc/README.PlanetCore b/doc/README.PlanetCore
deleted file mode 100644
index b73c5f5a87..0000000000
--- a/doc/README.PlanetCore
+++ /dev/null
@@ -1,163 +0,0 @@
-After several heart-struck failure, I got one workable way to program
-each other in FLASH between PlanetCore and U-Boot.
-
-Hardware Platform : RPXlite DW(EP 823 H1 DW)
-
-1. From U-Boot to PlanetCore
-
-Utilities : PlanetCore Boot Loader - PCL200.mot
-
-[root@sam tftpboot]# ppc_8xx-objcopy -O ppcboot
-PCL200.mot pcl200.bin
-
-[Target Operation]
-u-boot>t 100000 pcl200.bin
-u-boot>go 0x100000
-## Starting application at 0x00100000 ...
-
-MPC8xx PlanetCore Flash Burner v2.00
-Copyright 2001 Embedded Planet.  All rights reserved.
-
-Construct Flash Device.....done.
-
-
-Program MPC8xx PlanetCore Boot Loader v2.00
-Built Sep 19, 2001 at 14:34:42
-Image located from FC000000 to FC01B5D1.
-(Skipping an image, only loading low boot image)
-
-Low boot board detected, skipping high boot image.
-Erasing, programming and verifying will start in 20
-seconds
-Press P to start immediately or ESC to cancel
-Press Space or Enter for more options.
-..............
-
-Erasing
-Programming
-FLASH programmed successfully!
-Press R to induce a hard reset
-
-MPC8xx PlanetCore Boot Loader v2.00
-Copyright 2001 Embedded Planet.  All rights reserved.
-DRAM available size = 64 MB
-wvCV
-DRAM OK
->
-
-2. From PlanetCore to U-Boot
-
-Utilities : PlanetCore FLASH Burner - PCB200.mot
-
-Use Flash Burner to finish the work:
-
-First, TFTP the U-Boot image file to RAM; For example,
-RPXlite_DW.bin to 0x400000
-Second, TFTP FLASH Burner to RAM; For example,
-0x100000
-Third, run the FLASH Burner and Program the U-Boot
-image into the correct location in FLASH.
-
-[Target Operation]
-MPC8xx PlanetCore Boot Loader v2.00
-Copyright 2001 Embedded Planet.  All rights reserved.
-DRAM available size = 64 MB
-wvCV
-DRAM OK
->t
-Load using tftp via Ethernet
-Enter server IP address <172.16.115.6> :
-Enter server filename   <PCL200.mot> : RPXlite_DW.bin
-Enter (B)inary or (S)record input mode <S> : B
-Enter address offset  : <00400000 hex> :
-
-Total bytes = 120096 in 232184 uSecs
-Loaded addresses 00400000 through 0041D51F.
-Start address = 00400000
->t
-Load using tftp via Ethernet
-Enter server IP address <172.16.115.6> :
-Enter server filename   <RPXlite_DW.bin> : PCB200.mot
-Enter (B)inary or (S)record input mode <B> : S
-Enter address offset  : <00000000 hex> :
-.512.1024..2048....4096.....
-Total bytes = 326280 in 2570249 uSecs
-Loaded addresses 00100000 through 0011BB51.
-Start address = 00100000
->go
-[Go 00100000]
-
-MPC8xx PlanetCore Flash Burner v2.00
-Copyright 2001 Embedded Planet.  All rights reserved.
-
-Construct Flash Device.....done.
-
-Bad start address
-Start = 0xFFFFFFFF, target = 0xFFFFFFFF, length =
-0xFFFFFFFF
-Forcing Menu Interface
-
-h[elp]     Show commands.
-c[ode]     Show information on code to be loaded.
-di[splay]  Display all flash sections.
-du[mp]     Dump memory. d ? for more info.
-e[rase]    Erase flash sections.
-f[ill]     Fill flash sections.
-im[age]    Toggle load high, low, or both flash
-images.
-in[fo]     Show flash information.
-ma[p]      Show memory map.
-mo[dify]   Modify memory.  m ? for more info.
-p[rogram]  Erase, program, and verify now.
-reset      Restart the loader.
-s[how]     Show flash sections to erase and program.
-t[est]     Test flash sections.
-q[uit]     Quit without programming.
-#program 400000 ff000000 1D51F
-doProgram( 400000 ff000000 1D51F )
-
-Start = 0x00400000, target = 0xFF000000, length =
-0x0001D51F
-Erasing sector 0xFF000000, length 0x008000.
-Erasing sector 0xFF008000, length 0x008000.
-Erasing sector 0xFF010000, length 0x008000.
-Erasing sector 0xFF018000, length 0x008000.
-Programming FF000000 through FF01D51E
-FLASH programmed successfully!
-Press R to induce a hard reset
-
-Forcing Hard Reset by MachineCheck and
-ResetOnCheckstop...
-
-U-Boot 1.1.2 (Aug 29 2004 - 15:11:27)
-
-CPU:   PPC823EZTnnB2 at 48 MHz: 16 kB I-Cache 8 kB
-D-Cache
-Board: RPXlite_DW
-DRAM:  64 MB
-FLASH: 16 MB
-*** Warning - bad CRC, using default environment
-
-In:    serial
-Out:   serial
-Err:   serial
-Net:   SCC ETHERNET
-u-boot>
-
--------------------------------------------------
-
-Well, sometimes network function of PlanetCore couldn't work when
-switching from U-Boot to PlanetCore. For example, you couldn't
-download a file from HOST PC via TFTP. Don't worry, just restart your
-HOST PC and everything would work as smooth as clockwork. I don't
-know the reason WHY:-)
-
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Merry Christmas and Happy New Year!
-
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-=====
-Best regards,
-
-Sam