summaryrefslogtreecommitdiff
path: root/doc/README.mpc7448hpc2
diff options
context:
space:
mode:
authorMarkus Klotzbuecher <mk@denx.de>2007-04-23 13:17:22 +0200
committerMarkus Klotzbuecher <mk@pollux.denx.de>2007-04-23 13:17:22 +0200
commit61ea75aa07838435ec570ac85a2e3fc038844596 (patch)
tree20135a513c4c9d0bddb2a8ceaf009a8ed5e8bbdf /doc/README.mpc7448hpc2
parente2fb36a57f364016b973b1db255531e07cfefd52 (diff)
parent14da5f7675bbb427c469e3f45006e027b6e21db9 (diff)
Merge with git://www.denx.de/git/u-boot.git
Diffstat (limited to 'doc/README.mpc7448hpc2')
-rw-r--r--doc/README.mpc7448hpc2184
1 files changed, 184 insertions, 0 deletions
diff --git a/doc/README.mpc7448hpc2 b/doc/README.mpc7448hpc2
new file mode 100644
index 0000000000..8659e83673
--- /dev/null
+++ b/doc/README.mpc7448hpc2
@@ -0,0 +1,184 @@
+Freescale MPC7448hpc2 (Taiga) board
+===================================
+
+Created 08/11/2006 Roy Zang
+--------------------------
+MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference
+design, which is optimized for high speed throughput between the processor and
+the memory, disk drive and Ethernet port subsystems.
+
+MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be
+used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX
+chassis.
+
+Building U-Boot
+------------------
+The mpc7448hpc2 code base is known to compile using:
+ Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3
+
+ $ make mpc7448hpc2_config
+ Configuring for mpc7448hpc2 board...
+
+ $ make
+
+Memory Map
+----------
+
+The memory map is setup for Linux to operate properly.
+
+The mapping is:
+
+ Range Start Range End Definition Size
+
+ 0x0000_0000 0x7fff_ffff DDR 2G
+ 0xe000_0000 0xe7ff_ffff PCI Memory 128M
+ 0xfa00_0000 0xfaff_ffff PCI IO 16M
+ 0xfb00_0000 0xfbff_ffff PCI Config 16M
+ 0xfc00_0000 0xfc0f_ffff NVRAM/CADMUS 1M
+ 0xfe00_0000 0xfeff_ffff PromJet 16M
+ 0xff00_0000 0xff80_0000 FLASH (boot flash) 8M
+ 0xff80_0000 0xffff_ffff FLASH (second half flash) 8M
+
+Using Flash
+-----------
+
+The MPC7448hpc2 board has two "banks" of flash, each 8MB in size
+(2^23 = 0x00800000).
+
+Note: the "bank" here refers to half of the flash. In fact, there is only one
+bank of flash, which is divided into low and high half. Each is controlled by
+the most significant bit of the address bus. The so called "bank" is only for
+convenience.
+
+There is a switch which allows the "bank" to be selected. The switch
+settings for updating flash are given below.
+
+The u-boot commands for copying the boot-bank into the secondary bank are
+as follows:
+
+ erase ff800000 ff880000
+ cp.b ff000000 ff800000 80000
+
+U-boot commands for downloading an image via tftp and flashing
+it into the secondary bank:
+
+ tftp 10000 <u-boot.bin.image>
+ erase ff000000 ff080000
+ cp.b 10000 ff000000 80000
+
+After copying the image into the second bank of flash, be sure to toggle
+SW3[4] on board before resetting the board in order to set the
+secondary bank as the boot-bank.
+
+Board Switches
+----------------------
+
+Most switches on the board should not be changed. The most frequent
+user-settable switches on the board are used to configure
+the flash banks and determining the PCI frequency.
+
+SW1[1-5]: Processor core voltage
+
+ 12345 Core Voltage
+ -----
+ SW1=01111 1.000V.
+ SW1=01101 1.100V.
+ SW1=01011 1.200V.
+ SW1=01001 1.300V only for MPC7447A.
+
+
+SW2[1-6]: CPU core frequency
+
+ CPU Core Frequency (MHz)
+ Bus Frequency
+ 123456 100 133 167 200 Ratio
+
+ ------
+ SW2=101100 500 667 833 1000 5x
+ SW2=100100 550 733 917 1100 5.5x
+ SW2=110100 600 800 1000 1200 6x
+ SW2=010100 650 866 1083 1300 6.5x
+ SW2=001000 700 930 1167 1400 7x
+ SW2=000100 750 1000 1250 1500 7.5x
+ SW2=110000 800 1066 1333 1600 8x
+ SW2=011000 850 1333 1417 1700 8.5x only for MPC7447A
+ SW2=011110 900 1200 1500 1800 9x
+
+This table shows only a subset of available frequency options; see the CPU
+hardware specifications for more information.
+
+SW2[7-8]: Bus Protocol and CPU Reset Option
+
+ 7
+ -
+ SW2=0 System bus uses MPX bus protocol
+ SW2=1 System bus uses 60x bus protocol
+
+ 8
+ -
+ SW2=0 TSI108 can cause CPU reset
+ SW2=1 TSI108 can not cause CPU reset
+
+SW3[1-8] system options
+
+ 123
+ ---
+ SW3=xxx Connected to GPIO[0:2] on TSI108
+
+ 4
+ -
+ SW3=0 CPU boots from low half of flash
+ SW3=1 CPU boots from high half of flash
+
+ 5
+ -
+ SW3=0 SATA and slot2 connected to PCI bus
+ SW3=1 Only slot1 connected to PCI bus
+
+ 6
+ -
+ SW3=0 USB connected to PCI bus
+ SW3=1 USB disconnected from PCI bus
+
+ 7
+ -
+ SW3=0 Flash is write protected
+ SW3=1 Flash is NOT write protected
+
+ 8
+ -
+ SW3=0 CPU will boot from flash
+ SW3=1 CPU will boot from PromJet
+
+SW4[1-3]: System bus frequency
+
+ Bus Frequency (MHz)
+ ---
+ SW4=010 183
+ SW4=011 100
+ SW4=100 133
+ SW4=101 166 only for MPC7447A
+ SW4=110 200 only for MPC7448
+ others reserved
+
+SW4[4-6]: DDR2 SDRAM frequency
+
+ Bus Frequency (MHz)
+ ---
+ SW4=000 external clock
+ SW4=011 system clock
+ SW4=100 133
+ SW4=101 166
+ SW4=110 200
+ others reserved
+
+SW4[7-8]: PCI/PCI-X frequency control
+ 7
+ -
+ SW4=0 PCI/PCI-X bus operates normally
+ SW4=1 PCI bus forced to PCI-33 mode
+
+ 8
+ -
+ SW4=0 PCI-X mode at 133 MHz allowed
+ SW4=1 PCI-X mode limited to 100 MHz