doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 0 insertions, 166 deletions

diff --git a/doc/README.mpc8572ds b/doc/README.mpc8572ds
deleted file mode 100644
index 57fd2ad616..0000000000
--- a/doc/README.mpc8572ds
+++ /dev/null
@@ -1,166 +0,0 @@
-Overview
---------
-MPC8572DS is a high-performance computing, evaluation and development platform
-supporting the mpc8572 PowerTM processor.
-
-Building U-boot
------------
-	make MPC8572DS_config
-	make
-
-Flash Banks
------------
-MPC8572DS board has two flash banks. They are both present on boot, but their
-locations can be swapped using the dip-switch SW9[1:2].
-
-Booting is always from the boot bank at 0xec00_0000.
-
-
-Memory Map
-----------
-
-0xe800_0000 - 0xebff_ffff	Alternate bank		64MB
-0xec00_0000 - 0xefff_ffff	Boot bank		64MB
-
-0xebf8_0000 - 0xebff_ffff	Alternate u-boot address	512KB
-0xeff8_0000 - 0xefff_ffff	Boot u-boot address		512KB
-
-
-Flashing Images
----------------
-
-To place a new u-boot image in the alternate flash bank and then reset with that
- new image temporarily, use this:
-
-	tftp 1000000 u-boot.bin
-	erase ebf80000 ebffffff
-	cp.b 1000000 ebf80000 80000
-	pixis_reset altbank
-
-
-To program the image in the boot flash bank:
-
-	tftp 1000000 u-boot.bin
-	protect off all
-	erase eff80000 ffffffff
-	cp.b 1000000 eff80000 80000
-
-
-The pixis_reset command
------------------------
-The command - "pixis_reset", is introduced to reset mpc8572ds board
-using the FPGA sequencer.  When the board restarts, it has the option
-of using either the current or alternate flash bank as the boot
-image, with or without the watchdog timer enabled, and finally with
-or without frequency changes.
-
-Usage is;
-
-	pixis_reset
-	pixis_reset altbank
-	pixis_reset altbank wd
-	pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
-	pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
-
-Examples:
-
-	/* reset to current bank, like "reset" command */
-	pixis_reset
-
-	/* reset board but use the to alternate flash bank */
-	pixis_reset altbank
-
-
-Using the Device Tree Source File
----------------------------------
-To create the DTB (Device Tree Binary) image file,
-use a command similar to this:
-
-	dtc -b 0 -f -I dts -O dtb mpc8572ds.dts > mpc8572ds.dtb
-
-Likely, that .dts file will come from here;
-
-	linux-2.6/arch/powerpc/boot/dts/mpc8572ds.dts
-
-
-Booting Linux
--------------
-
-Place a linux uImage in the TFTP disk area.
-
-	tftp 1000000 uImage.8572
-	tftp c00000 mpc8572ds.dtb
-	bootm 1000000 - c00000
-
-
-Implementing AMP(Asymmetric MultiProcessing)
--------------
-1. Build kernel image for core0:
-
-	a. $ make 85xx/mpc8572_ds_defconfig
-
-	b. $ make menuconfig
-	   - un-select "Processor support"->"Symetric multi-processing support"
-
-	c. $ make uImage
-
-	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
-
-2. Build kernel image for core1:
-
-	a. $ make 85xx/mpc8572_ds_defconfig
-
-	b. $ make menuconfig
-	   - Un-select "Processor support"->"Symetric multi-processing support"
-	   - Select "Advanced setup" -> " Prompt for advanced kernel
-	     configuration options"
-		- Select "Set physical address where the kernel is loaded" and
-		  set it to 0x20000000, assuming core1 will start from 512MB.
-		- Select "Set custom page offset address"
-		- Select "Set custom kernel base address"
-		- Select "Set maximum low memory"
-	   - "Exit" and save the selection.
-
-	c. $ make uImage
-
-	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
-
-3. Create dtb for core0:
-
-	$ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
-
-4. Create dtb for core1:
-
-	$ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
-
-5. Bring up two cores separately:
-
-	a. Power on the board, under u-boot prompt:
-		=> setenv <serverip>
-		=> setenv <ipaddr>
-		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
-	b. Bring up core1's kernel first:
-		=> setenv bootm_low 0x20000000
-		=> setenv bootm_size 0x10000000
-		=> tftp 21000000 8572/uImage.core1
-		=> tftp 22000000 8572/ramdiskfile
-		=> tftp 20c00000 8572/mpc8572ds_core1.dtb
-		=> interrupts off
-		=> bootm start 21000000 22000000 20c00000
-		=> bootm loados
-		=> bootm ramdisk
-		=> bootm fdt
-		=> fdt boardsetup
-		=> fdt chosen $initrd_start $initrd_end
-		=> bootm prep
-		=> cpu 1 release $bootm_low - $fdtaddr -
-	c. Bring up core0's kernel(on the same u-boot console):
-		=> setenv bootm_low 0
-		=> setenv bootm_size 0x20000000
-		=> tftp 1000000 8572/uImage.core0
-		=> tftp 2000000 8572/ramdiskfile
-		=> tftp c00000 8572/mpc8572ds_core0.dtb
-		=> bootm 1000000 2000000 c00000
-
-Please note only core0 will run u-boot, core1 starts kernel directly after
-"cpu release" command is issued.