README.mx28_common: Rename it to README.mxs

commit 54965b61360 (README: mxs: Introduce README.mxs) should have changed the
file name to README.mxs, as it covers both mx23 and mx28 now.

Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

1 files changed, 0 insertions, 236 deletions

diff --git a/doc/README.mx28_common b/doc/README.mx28_common
deleted file mode 100644
index 5d9e72f958..0000000000
--- a/doc/README.mx28_common
+++ /dev/null
@@ -1,236 +0,0 @@
-Booting U-boot on a MXS processor
-=================================
-
-This document describes the MXS U-Boot port. This document mostly covers topics
-related to making the module/board bootable.
-
-Terminology
------------
-
-The term "MXS" refers to a family of Freescale SoCs that is composed by MX23
-and MX28.
-
-The dollar symbol ($) introduces a snipped of shell code. This shall be typed
-into the unix command prompt in U-Boot source code root directory.
-
-The (=>) introduces a snipped of code that should by typed into U-Boot command
-prompt
-
-Contents
---------
-
-1) Prerequisites
-2) Compiling U-Boot for a MXS based board
-3) Installation of U-Boot for a MXS based board to SD card
-4) Installation of U-Boot into NAND flash on a MX28 based board
-
-1) Prerequisites
-----------------
-
-To make a MXS based board bootable, some tools are necessary. The first one is
-the "elftosb" tool distributed by Freescale Semiconductor. The other one is the
-"mxsboot" tool found in U-Boot source tree.
-
-Firstly, obtain the elftosb archive from the following location:
-
-	ftp://ftp.denx.de/pub/tools/elftosb-10.12.01.tar.gz
-
-We use a $VER variable here to denote the current version. At the time of
-writing of this document, that is "10.12.01". To obtain the file from command
-line, use:
-
-	$ VER="10.12.01"
-	$ wget ftp://ftp.denx.de/pub/tools/elftosb-${VER}.tar.gz
-
-Extract the file:
-
-	$ tar xzf elftosb-${VER}.tar.gz
-
-Compile the file. We need to manually tell the linker to use also libm:
-
-	$ cd elftosb-${VER}/
-	$ make LIBS="-lstdc++ -lm" elftosb
-
-Optionally, remove debugging symbols from elftosb:
-
-	$ strip bld/linux/elftosb
-
-Finally, install the "elftosb" binary. The "install" target is missing, so just
-copy the binary by hand:
-
-	$ sudo cp bld/linux/elftosb /usr/local/bin/
-
-Make sure the "elftosb" binary can be found in your $PATH, in this case this
-means "/usr/local/bin/" has to be in your $PATH.
-
-2) Compiling U-Boot for a MXS based board
--------------------------------------------
-
-Compiling the U-Boot for a MXS board is straightforward and done as compiling
-U-Boot for any other ARM device. For cross-compiler setup, please refer to
-ELDK5.0 documentation. First, clean up the source code:
-
-	$ make mrproper
-
-Next, configure U-Boot for a MXS based board
-
-	$ make <mxs_based_board_name>_config
-
-Examples:
-
-1. For building U-boot for Denx M28EVK board:
-
-	$ make m28evk_config
-
-2. For building U-boot for Freescale MX28EVK board:
-
-	$ make mx28evk_config
-
-3. For building U-boot for Freescale MX23EVK board:
-
-	$ make mx23evk_config
-
-4. For building U-boot for Olimex MX23 Olinuxino board:
-
-	$ make mx23_olinuxino_config
-
-Lastly, compile U-Boot and prepare a "BootStream". The "BootStream" is a special
-type of file, which MXS CPUs can boot. This is handled by the following
-command:
-
-	$ make u-boot.sb
-
-HINT: To speed-up the build process, you can add -j<N>, where N is number of
-      compiler instances that'll run in parallel.
-
-The code produces "u-boot.sb" file. This file needs to be augmented with a
-proper header to allow successful boot from SD or NAND. Adding the header is
-discussed in the following chapters.
-
-3) Installation of U-Boot for a MXS based board to SD card
-----------------------------------------------------------
-
-To boot a MXS based board from SD, set the boot mode DIP switches according to
-to MX28 manual, section 12.2.1 (Table 12-2) or MX23 manual, section 35.1.2
-(Table 35-3).
-
-The SD card used to boot U-Boot must contain a DOS partition table, which in
-turn carries a partition of special type and which contains a special header.
-The rest of partitions in the DOS partition table can be used by the user.
-
-To prepare such partition, use your favourite partitioning tool. The partition
-must have the following parameters:
-
-	* Start sector .......... sector 2048
-	* Partition size ........ at least 1024 kb
-	* Partition type ........ 0x53 (sometimes "OnTrack DM6 Aux3")
-
-For example in Linux fdisk, the sequence for a clear card follows. Be sure to
-run fdisk with the option "-u=sectors" to set units to sectors:
-
-	* o ..................... create a clear partition table
-	* n ..................... create new partition
-		* p ............. primary partition
-		* 1 ............. first partition
-		* 2048 .......... first sector is 2048
-		* +1M ........... make the partition 1Mb big
-	* t 1 ................... change first partition ID
-		* 53 ............ change the ID to 0x53 (OnTrack DM6 Aux3)
-	* <create other partitions>
-	* w ..................... write partition table to disk
-
-The partition layout is ready, next the special partition must be filled with
-proper contents. The contents is generated by running the following command
-(see chapter 2)):
-
-	$ ./tools/mxsboot sd u-boot.sb u-boot.sd
-
-The resulting file, "u-boot.sd", shall then be written to the partition. In this
-case, we assume the first partition of the SD card is /dev/mmcblk0p1:
-
-	$ dd if=u-boot.sd of=/dev/mmcblk0p1
-
-Last step is to insert the card into the MXS based board and boot.
-
-NOTE: If the user needs to adjust the start sector, the "mxsboot" tool contains
-      a "-p" switch for that purpose. The "-p" switch takes the sector number as
-      an argument.
-
-4) Installation of U-Boot into NAND flash on a MX28 based board
----------------------------------------------------------------
-
-To boot a MX28 based board from NAND, set the boot mode DIP switches according
-to MX28 manual section 12.2.1 (Table 12-2), PORT=GPMI, NAND 1.8 V.
-
-There are two possibilities when preparing an image writable to NAND flash.
-
-	I) The NAND wasn't written at all yet or the BCB is broken
-	----------------------------------------------------------
-	   In this case, both BCB (FCB and DBBT) and firmware needs to be
-	   written to NAND. To generate NAND image containing all these,
-	   there is a tool called "mxsboot" in the "tools/" directory. The tool
-	   is invoked on "u-boot.sb" file from chapter 2):
-
-		 $ ./tools/mxsboot nand u-boot.sb u-boot.nand
-
-	   NOTE: The above invokation works for NAND flash with geometry of
-		 2048b per page, 64b OOB data, 128kb erase size. If your chip
-		 has a different geometry, please use:
-
-		 -w <size>	change page size (default 2048 b)
-		 -o <size>	change oob size (default 64 b)
-		 -e <size>	change erase size (default 131072 b)
-
-		 The geometry information can be obtained from running U-Boot
-		 on the MX28 board by issuing the "nand info" command.
-
-	   The resulting file, "u-boot.nand" can be written directly to NAND
-	   from the U-Boot prompt. To simplify the process, the U-Boot default
-	   environment contains script "update_nand_full" to update the system.
-
-	   This script expects a working TFTP server containing the file
-	   "u-boot.nand" in it's root directory. This can be changed by
-	   adjusting the "update_nand_full_filename" varible.
-
-	   To update the system, run the following in U-Boot prompt:
-
-		 => run update_nand_full
-
-	   In case you would only need to update the bootloader in future,
-	   see II) below.
-
-	II) The NAND was already written with a good BCB
-	------------------------------------------------
-	   This part applies after the part I) above was done at least once.
-
-	   If part I) above was done correctly already, there is no need to
-	   write the FCB and DBBT parts of NAND again. It's possible to upgrade
-	   only the bootloader image.
-
-	   To simplify the process of firmware update, the U-Boot default
-	   environment contains script "update_nand_firmware" to update only
-	   the firmware, without rewriting FCB and DBBT.
-
-	   This script expects a working TFTP server containing the file
-	   "u-boot.sb" in it's root directory. This can be changed by
-	   adjusting the "update_nand_firmware_filename" varible.
-
-	   To update the system, run the following in U-Boot prompt:
-
-		 => run update_nand_firmware
-
-	III) Special settings for the update scripts
-	--------------------------------------------
-	   There is a slight possibility of the user wanting to adjust the
-	   STRIDE and COUNT options of the NAND boot. For description of these,
-	   see MX28 manual section 12.12.1.2 and 12.12.1.3.
-
-	   The update scripts take this possibility into account. In case the
-	   user changes STRIDE by blowing fuses, the user also has to change
-	   "update_nand_stride" variable. In case the user changes COUNT by
-	   blowing fuses, the user also has to change "update_nand_count"
-	   variable for the update scripts to work correctly.
-
-	   In case the user needs to boot a firmware image bigger than 1Mb, the
-	   user has to adjust the "update_nand_firmware_maxsz" variable for the
-	   update scripts to work properly.