powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS

Drop support for these two legacy boards.

Signed-off-by: York Sun <york.sun@nxp.com>

1 files changed, 0 insertions, 301 deletions

diff --git a/doc/README.mpc85xxads b/doc/README.mpc85xxads
deleted file mode 100644
index 9b35fb2016..0000000000
--- a/doc/README.mpc85xxads
+++ /dev/null
@@ -1,301 +0,0 @@
-Motorola MPC8540ADS and MPC8560ADS board
-
-Created 10/15/03 Xianghua Xiao
-Updated 13-July-2004 Jon Loeliger
------------------------------------------
-
-0. Toolchain
-
-    The Binutils in current ELDK toolchain will not support MPC85xx
-    chip.  You need to use binutils-2.14.tar.bz2 (or newer) from
-    http://ftp.gnu.org/gnu/binutils.
-
-    The 8540/8560 ADS code base is known to compile using:
-	gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)
-
-
-1. SWITCH SETTINGS & JUMPERS
-
-1.0 Nomenclature
-
-    For some reason, the HW designers describe the switch settings
-    in terms of 0 and 1, and then map that to physical switches where
-    the label "On" refers to logic 0 and "Off" (unlabeled) is logic 1.
-    Luckily, we're SW types and virtual settings are handled daily.
-
-    The switches for the Rev A board are numbered differently than
-    for the Pilot board.  Oh yeah.
-
-    Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
-    bits may contribute to signals that are numbered based at 0,
-    and some of those signals may be high-bit-number-0 too.  Heed
-    well the names and labels and do not get confused.
-
-    "Off" == 1
-    "On"  == 0
-
-    SW18 is switch 18 as silk-screened onto the board.
-    SW4[8] is the bit labeled 8 on Switch 4.
-    SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2
-    SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3
-
-1.1 For the MPC85xxADS Pilot Board
-
-    First, make sure the board default setting is consistent with the document
-    shipped with your board. Then apply the following changes:
-    SW3[1-6]="all OFF"	(boot from 32bit flash, no boot sequence is used)
-    SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
-    SW11[2]='OFF for 8560, ON for 8540' (toggle 8540.8560 mode)
-    SW11[7]='ON' (rev2), 'OFF' (rev1)
-    SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
-    SW22[1-4]="OFF OFF ON OFF"
-    SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
-    J1 = "Enable Prog" (Make sure your flash is programmable for development)
-
-    If you want to test PCI functionality with a 33Mhz PCI card, you will
-    have to change the system clock from the default 66Mhz to 33Mhz by
-    setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
-    double your platform clock(SW6) because the system clock is now only
-    half of its original value. For example, if at 66MHz your system
-    clock showed SW6[0:1] = 01, then at 33MHz SW6[0:1] it should be 10.
-
-	SW17[8] ------+	   SW6
-	SW15[1] ----+ |	  [0:1]
-		    V V	   V V
-	33MHz	    1 1	   1 0
-	66MHz	    0 0	   0 1
-
-    Hmmm... That SW6 setting description is incomplete but it works.
-
-
-1.3 For the MPC85xxADS Rev A Board
-
-    As shipped, the board should be a 33MHz PCI bus with a CPU Clock
-    rate of 825 +/- fuzz:
-
-	Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC:	82 MHz
-
-    For 33MHz PCI, the switch settings should be like this:
-
-	SW18[7:1] = 0100001 = M==33 =>	  33MHz
-	SW18[8]	  =	  1	    => PWD Divider == 16
-	SW16[1:2] =	 11	    => N == 16 as PWD==1
-
-    Use the magical formula:
-	Fout (MHz) = 16 * M / N = 16 * 33 / 16 = 33 MHz
-
-	SW7[1:4]  =    1010 = 10    => 10 x 33	 = 330	CCB Sysclk
-	SW7[5:6]  =	 01	    => 5:2 x 330 = 825	Core clock
-
-
-    For 66MHz PCI, the switch settings should be like this:
-
-	SW18[7:1] = 0100001 = M==33 =>	  33MHz
-	SW18[8]	  =	  0	    => PWD Divider == 1
-	SW16[1:2] =	 01	    => N == 8 as PWD == 0
-
-    Use the magical formula:
-	Fout (MHz) = 16 * M / N = 16 * 33 / 8 = 66 MHz
-
-	SW7[1:4]  =    0101 =  5    => 5 x 66	 = 330	CCB Sysclk
-	SW7[5:6]  =	 01	    => 5:2 x 330 = 825	Core clock
-
-    In order to use PCI-X (only in the first PCI slot.  The one with
-    the RIO connector), you need to set SW1[4] (config) to 1 (off).
-    Also, configure the board to run PCI at 66 MHz.
-
-2. MEMORY MAP TO WORK WITH LINUX KERNEL
-
-2.1. For the initial bringup, we adopted a consistent memory scheme
-     between U-Boot and linux kernel, you can customize it based on your
-     system requirements:
-
-     0x0000_0000     0x7fff_ffff     DDR		     2G
-     0x8000_0000     0x9fff_ffff     PCI MEM		     512M
-     0xc000_0000     0xdfff_ffff     Rapid IO		     512M
-     0xe000_0000     0xe00f_ffff     CCSR		     1M
-     0xe200_0000     0xe2ff_ffff     PCI IO		     16M
-     0xf000_0000     0xf7ff_ffff     SDRAM		     128M
-     0xf800_0000     0xf80f_ffff     BCSR		     1M
-     0xff00_0000     0xffff_ffff     FLASH (boot bank)	     16M
-
-2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. You
-    can download them from linuxppc-2.4 public source. Please make sure the
-    kernel's ppcboot.h is consistent with U-Boot's u-boot.h. You can use two
-    default configuration files as your starting points to configure the
-    kernel:
-	arch/powerpc/configs/mpc8540_ads_defconfig
-	arch/powerpc/configs/mpc8560_ads_defconfig
-
-3. DEFINITIONS AND COMPILATION
-
-3.1 Explanation on NEW definitions in:
-	include/configs/MPC8540ADS.h
-	include/configs/MPC8560ADS.h
-
-    CONFIG_BOOKE	    BOOKE(e.g. Motorola MPC85xx, AMCC 440, etc)
-    CONFIG_E500		    BOOKE e500 family(Motorola)
-    CONFIG_MPC85xx	    MPC8540,MPC8560 and their derivatives
-    CONFIG_ARCH_MPC8540	    MPC8540 specific
-    CONFIG_TSEC_ENET	    Use on-chip 10/100/1000 ethernet for networking
-    CONFIG_SPD_EEPROM	    Use SPD EEPROM for DDR auto configuration, you can
-			    also manual config the DDR after undef this
-			    definition.
-    CONFIG_DDR_ECC	    only for ECC DDR module
-    CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN	    DLL fix on some ADS boards needed
-			    for more stability.
-    CONFIG_HAS_FEC	    If an FEC is on chip, set to 1, else 0.
-
-Other than the above definitions, the rest in the config files are
-straightforward.
-
-
-3.2 Compilation
-
-    Assuming you're using BASH shell:
-
-	export CROSS_COMPILE=your-cross-compile-prefix
-	cd u-boot
-	make distclean
-	make MPC8560ADS_config (or make MPC8540ADS_config)
-	make
-
-4.  Notes:
-
-4.1 When connecting with kermit, the following commands must be present.in
-    your .kermrc file. These are especially important when booting as
-    MPC8560, as the serial console will not work without them:
-
-	set speed 115200
-	set carrier-watch off
-	set handshake none
-	set flow-control none
-	robust
-
-
-4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC
-    ethernet. If that happens, you can try the following steps to make
-    network work:
-
-	MPC8560ADS>tftp 1000000 pImage
-	(if it hangs, use Ctrl-C to quit)
-	MPC8560ADS>nm fdf24524
-	>0
-	>1
-	>. (to quit this memory operation)
-	MPC8560ADS>tftp 1000000 pImage
-
-4.3 If you're one of the early developers using the Rev1 8540/8560 chips,
-    please use U-Boot 1.0.0, as the newer silicon will only support Rev2
-    and future revisions of 8540/8560.
-
-
-4.4 Reflash U-Boot Image using U-Boot
-
-    tftp 10000 u-boot.bin
-    protect off fff80000 ffffffff
-    erase fff80000 ffffffff
-    cp.b 10000 fff80000 80000
-
-
-4.5 Reflash U-Boot with a BDI-2000
-
-    BDI> erase 0xFFF80000 0x4000 0x20
-    BDI> prog 0xfff80000 u-boot.bin.8560ads
-    BDI> verify
-
-
-5. Screen dump MPC8540ADS board
-
-U-Boot 1.1.2(pq3-20040707-0) (Jul  6 2004 - 17:34:25)
-
-Freescale PowerPC
-    Core: E500, Version: 2.0, (0x80200020)
-    System: 8540, Version: 2.0, (0x80300020)
-    Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC:  82 MHz
-    L1 D-cache 32KB, L1 I-cache 32KB enabled.
-Board: ADS
-    PCI1: 32 bit, 66 MHz (compiled)
-I2C:   ready
-DRAM:  Initializing
-    SDRAM: 64 MB
-    DDR: 256 MB
-FLASH: 16 MB
-L2 cache enabled: 256KB
-*** Warning - bad CRC, using default environment
-
-In:    serial
-Out:   serial
-Err:   serial
-Net:   MOTO ENET0: PHY is Marvell 88E1011S (1410c62)
-MOTO ENET1: PHY is Marvell 88E1011S (1410c62)
-MOTO ENET2: PHY is Davicom DM9161E (181b881)
-MOTO ENET0, MOTO ENET1, MOTO ENET2
-Hit any key to stop autoboot:  0
-=>
-=> fli
-
-Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
-  Size: 16 MB in 64 Sectors
-  Sector Start Addresses:
-    FF000000	  FF040000	FF080000      FF0C0000	    FF100000
-    FF140000	  FF180000	FF1C0000      FF200000	    FF240000
-    FF280000	  FF2C0000	FF300000      FF340000	    FF380000
-    FF3C0000	  FF400000	FF440000      FF480000	    FF4C0000
-    FF500000	  FF540000	FF580000      FF5C0000	    FF600000
-    FF640000	  FF680000	FF6C0000      FF700000	    FF740000
-    FF780000	  FF7C0000	FF800000      FF840000	    FF880000
-    FF8C0000	  FF900000	FF940000      FF980000	    FF9C0000
-    FFA00000	  FFA40000	FFA80000      FFAC0000	    FFB00000
-    FFB40000	  FFB80000	FFBC0000      FFC00000	    FFC40000
-    FFC80000	  FFCC0000	FFD00000      FFD40000	    FFD80000
-    FFDC0000	  FFE00000	FFE40000      FFE80000	    FFEC0000
-    FFF00000	  FFF40000	FFF80000 (RO) FFFC0000 (RO)
-
-=> bdinfo
-memstart    = 0x00000000
-memsize	    = 0x10000000
-flashstart  = 0xFF000000
-flashsize   = 0x01000000
-flashoffset = 0x00000000
-sramstart   = 0x00000000
-sramsize    = 0x00000000
-immr_base   = 0xE0000000
-bootflags   = 0xE4013F80
-intfreq	    =	 825 MHz
-busfreq	    =	 330 MHz
-ethaddr	    = 00:E0:0C:00:00:FD
-eth1addr    = 00:E0:0C:00:01:FD
-eth2addr    = 00:E0:0C:00:02:FD
-IP addr	    = 192.168.1.253
-baudrate    = 115200 bps
-
-
-=> printenv
-bootcmd=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
-ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;bootm $loadaddr $ramdiskaddr
-nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
-bootdelay=10
-baudrate=115200
-loads_echo=1
-ethaddr=00:E0:0C:00:00:FD
-eth1addr=00:E0:0C:00:01:FD
-eth2addr=00:E0:0C:00:02:FD
-ipaddr=192.168.1.253
-serverip=192.168.1.1
-rootpath=/nfsroot
-gatewayip=192.168.1.1
-netmask=255.255.255.0
-hostname=unknown
-bootfile=your.uImage
-loadaddr=200000
-netdev=eth0
-consoledev=ttyS0
-ramdiskaddr=400000
-ramdiskfile=your.ramdisk.u-boot
-stdin=serial
-stdout=serial
-stderr=serial
-ethact=MOTO ENET0
-
-Environment size: 1020/8188 bytes