Merge tag 'xilinx-for-v2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2020.07

common:
- Align ENV_FAT_INTERFACE
- Fix MAC address source print log
- Improve based autodetection code

xilinx:
- Enable netconsole

Microblaze:
- Setup default ENV_OFFSET/ENV_SECT_SIZE

Zynq:
- Multiple DT updates/fixes
- Use DEVICE_TREE environment variable for DTB selection
- Switch to single zynq configuration
- Enable NOR flash via DM
- Minor SPL print removal
- Enable i2c mux driver

ZynqMP:
- Print multiboot register
- Enable cache commands in mini mtest
- Multiple DT updates/fixes
- Fix firmware probing when driver is not enabled
- Specify 3rd backup RAM boot mode in SPL
- Add SPL support for zcu102 v1.1 and zcu111 revA
- Redesign debug uart enabling and psu_init delay
- Enable full u-boot run from EL3
- Enable u-boot.itb generation without ATF with U-Boot in EL3

Versal:
- Enable distro default
- Enable others SPI flashes
- Enable systems without DDR

Drivers:
- Gem:
  - Flush memory after freeing
  - Handle mdio bus separately
- Watchdog:
  - Get rid of unused global data pointer
  - Enable window watchdog timer
- Serial:
  - Change reinitialization logic in zynq serial driver

Signed-off-by: Tom Rini <trini@konsulko.com>

1 files changed, 14 insertions, 11 deletions

diff --git a/drivers/mtd/nand/raw/zynq_nand.c b/drivers/mtd/nand/raw/zynq_nand.c
index 28db4153f5..0aea83dac0 100644
--- a/drivers/mtd/nand/raw/zynq_nand.c
+++ b/drivers/mtd/nand/raw/zynq_nand.c
@@ -1081,18 +1081,23 @@ static int zynq_nand_probe(struct udevice *dev)
 	u8 set_feature[4] = {ONDIE_ECC_FEATURE_ENABLE, 0x00, 0x00, 0x00};
 	unsigned long ecc_cfg;
 	int ondie_ecc_enabled = 0;
-	int err = -1;
 	int is_16bit_bw;
 
 	smc->reg = (struct zynq_nand_smc_regs *)dev_read_addr(dev);
 	of_nand = dev_read_subnode(dev, "flash@e1000000");
 	if (!ofnode_valid(of_nand)) {
 		printf("Failed to find nand node in dt\n");
-		goto fail;
+		return -ENODEV;
 	}
+
+	if (!ofnode_is_available(of_nand)) {
+		debug("Nand node in dt disabled\n");
+		return dm_scan_fdt_dev(dev);
+	}
+
 	if (ofnode_read_resource(of_nand, 0, &res)) {
 		printf("Failed to get nand resource\n");
-		goto fail;
+		return -ENODEV;
 	}
 
 	xnand->nand_base = (void __iomem *)res.start;
@@ -1119,7 +1124,7 @@ static int zynq_nand_probe(struct udevice *dev)
 	if (is_16bit_bw == NAND_BW_UNKNOWN) {
 		printf("%s: Unable detect NAND based on MIO settings\n",
 		       __func__);
-		goto fail;
+		return -EINVAL;
 	}
 
 	if (is_16bit_bw == NAND_BW_16BIT)
@@ -1130,13 +1135,13 @@ static int zynq_nand_probe(struct udevice *dev)
 	/* Initialize the NAND flash interface on NAND controller */
 	if (zynq_nand_init_nand_flash(mtd, nand_chip->options) < 0) {
 		printf("%s: nand flash init failed\n", __func__);
-		goto fail;
+		return -EINVAL;
 	}
 
 	/* first scan to find the device and get the page size */
 	if (nand_scan_ident(mtd, 1, NULL)) {
 		printf("%s: nand_scan_ident failed\n", __func__);
-		goto fail;
+		return -EINVAL;
 	}
 	/* Send the command for reading device ID */
 	nand_chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
@@ -1261,14 +1266,12 @@ static int zynq_nand_probe(struct udevice *dev)
 	/* Second phase scan */
 	if (nand_scan_tail(mtd)) {
 		printf("%s: nand_scan_tail failed\n", __func__);
-		goto fail;
+		return -EINVAL;
 	}
 	if (nand_register(0, mtd))
-		goto fail;
+		return -EINVAL;
+
 	return 0;
-fail:
-	free(xnand);
-	return err;
 }
 
 static const struct udevice_id zynq_nand_dt_ids[] = {