85xx: add ability to upload QE firmware

Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it.  Add function qe_upload_firmware() to parse the blob and
perform the actual upload.  Add command-line command "qe fw" to take a firmware
blob in memory and upload it.  Update ft_cpu_setup() on 85xx to create the
'firmware' device tree node if U-Boot has uploaded a firmware.  Fully define
'struct rsp' in immap_qe.h to include the actual RISC Special Registers.

Signed-off-by: Timur Tabi <timur@freescale.com>

1 files changed, 56 insertions, 0 deletions

diff --git a/drivers/qe/qe.h b/drivers/qe/qe.h
index 400b1a6f60..4c96c67ff3 100644
--- a/drivers/qe/qe.h
+++ b/drivers/qe/qe.h
@@ -222,6 +222,60 @@ typedef enum qe_clock {
 
 #define QE_SDEBCR_BA_MASK		0x01FFFFFF
 
+/* Communication Processor */
+#define QE_CP_CERCR_MEE		0x8000	/* Multi-user RAM ECC enable */
+#define QE_CP_CERCR_IEE		0x4000	/* Instruction RAM ECC enable */
+#define QE_CP_CERCR_CIR		0x0800	/* Common instruction RAM */
+
+/* I-RAM */
+#define QE_IRAM_IADD_AIE	0x80000000	/* Auto Increment Enable */
+#define QE_IRAM_IADD_BADDR	0x00080000	/* Base Address */
+
+/* Structure that defines QE firmware binary files.
+ *
+ * See doc/README.qe_firmware for a description of these fields.
+ */
+struct qe_firmware {
+	struct qe_header {
+		u32 length;  /* Length of the entire structure, in bytes */
+		u8 magic[3];    /* Set to { 'Q', 'E', 'F' } */
+		u8 version;     /* Version of this layout. First ver is '1' */
+	} header;
+	u8 id[62];      /* Null-terminated identifier string */
+	u8 split;	/* 0 = shared I-RAM, 1 = split I-RAM */
+	u8 count;       /* Number of microcode[] structures */
+	struct {
+		u16 model;   	/* The SOC model  */
+		u8 major;       	/* The SOC revision major */
+		u8 minor;       	/* The SOC revision minor */
+	} __attribute__ ((packed)) soc;
+	u8 padding[4];			/* Reserved, for alignment */
+	u64 extended_modes;		/* Extended modes */
+	u32 vtraps[8];		/* Virtual trap addresses */
+	u8 reserved[4];			/* Reserved, for future expansion */
+	struct qe_microcode {
+		u8 id[32];      	/* Null-terminated identifier */
+		u32 traps[16];       /* Trap addresses, 0 == ignore */
+		u32 eccr;    	/* The value for the ECCR register */
+		u32 iram_offset;     /* Offset into I-RAM for the code */
+		u32 count;   	/* Number of 32-bit words of the code */
+		u32 code_offset;     /* Offset of the actual microcode */
+		u8 major;       	/* The microcode version major */
+		u8 minor;       	/* The microcode version minor */
+		u8 revision;		/* The microcode version revision */
+		u8 padding;		/* Reserved, for alignment */
+		u8 reserved[4];		/* Reserved, for future expansion */
+	} __attribute__ ((packed)) microcode[1];
+	/* All microcode binaries should be located here */
+	/* CRC32 should be located here, after the microcode binaries */
+} __attribute__ ((packed));
+
+struct qe_firmware_info {
+	char id[64];		/* Firmware name */
+	u32 vtraps[8];		/* Virtual trap addresses */
+	u64 extended_modes;	/* Extended modes */
+};
+
 void qe_config_iopin(u8 port, u8 pin, int dir, int open_drain, int assign);
 void qe_issue_cmd(uint cmd, uint sbc, u8 mcn, u32 cmd_data);
 uint qe_muram_alloc(uint size, uint align);
@@ -233,5 +287,7 @@ void qe_reset(void);
 void qe_assign_page(uint snum, uint para_ram_base);
 int qe_set_brg(uint brg, uint rate);
 int qe_set_mii_clk_src(int ucc_num);
+int qe_upload_firmware(const struct qe_firmware *firmware);
+struct qe_firmware_info *qe_get_firmware_info(void);
 
 #endif /* __QE_H__ */