pinctrl: Add pinctrl driver for i.MX8

Add pinctrl driver for i.MX8. The pads configuration is controlled
by SCU, so need to ask SCU to configure pads through scfw API.
Add pinctrl-scu to invoke sc_pad_set to configure pads.
Add a new flag IMX8_USE_SCU to differentiate i.MX8 from other platforms
which could directly configure pads from Acore side.
Add CONFIG_PINCTRL_IMX8 as the built gate.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

6 files changed, 258 insertions, 93 deletions

diff --git a/drivers/pinctrl/nxp/Kconfig b/drivers/pinctrl/nxp/Kconfig
index b668359a0b..799d1d2465 100644
--- a/drivers/pinctrl/nxp/Kconfig
+++ b/drivers/pinctrl/nxp/Kconfig
@@ -1,6 +1,9 @@
 config PINCTRL_IMX
 	bool
 
+config PINCTRL_IMX_SCU
+	bool
+
 config PINCTRL_IMX5
 	bool "IMX5 pinctrl driver"
 	depends on ARCH_MX5 && PINCTRL_FULL
@@ -56,3 +59,18 @@ config PINCTRL_IMX7ULP
 	  is different from the linux one, this is a simple implementation,
 	  only parses the 'fsl,pins' property and configure related
 	  registers.
+
+config PINCTRL_IMX8
+	bool "IMX8 pinctrl driver"
+	depends on ARCH_IMX8 && PINCTRL_FULL
+	select DEVRES
+	select PINCTRL_IMX
+	select PINCTRL_IMX_SCU
+	help
+	  Say Y here to enable the imx8 pinctrl driver
+
+	  This provides a simple pinctrl driver for i.MX8 SoC familiy.
+	  This feature depends on device tree configuration. This driver
+	  is different from the linux one, this is a simple implementation,
+	  only parses the 'fsl,pins' property and configures related
+	  registers.
diff --git a/drivers/pinctrl/nxp/Makefile b/drivers/pinctrl/nxp/Makefile
index c763948376..310b3b3a2e 100644
--- a/drivers/pinctrl/nxp/Makefile
+++ b/drivers/pinctrl/nxp/Makefile
@@ -3,3 +3,5 @@ obj-$(CONFIG_PINCTRL_IMX5)		+= pinctrl-imx5.o
 obj-$(CONFIG_PINCTRL_IMX6)		+= pinctrl-imx6.o
 obj-$(CONFIG_PINCTRL_IMX7)		+= pinctrl-imx7.o
 obj-$(CONFIG_PINCTRL_IMX7ULP)		+= pinctrl-imx7ulp.o
+obj-$(CONFIG_PINCTRL_IMX_SCU)		+= pinctrl-scu.o
+obj-$(CONFIG_PINCTRL_IMX8)		+= pinctrl-imx8.o
diff --git a/drivers/pinctrl/nxp/pinctrl-imx.c b/drivers/pinctrl/nxp/pinctrl-imx.c
index 36e1e8983c..04ea82aba5 100644
--- a/drivers/pinctrl/nxp/pinctrl-imx.c
+++ b/drivers/pinctrl/nxp/pinctrl-imx.c
@@ -28,7 +28,9 @@ static int imx_pinctrl_set_state(struct udevice *dev, struct udevice *config)
 
 	dev_dbg(dev, "%s: %s\n", __func__, config->name);
 
-	if (info->flags & SHARE_MUX_CONF_REG)
+	if (info->flags & IMX8_USE_SCU)
+		pin_size = SHARE_IMX8_PIN_SIZE;
+	else if (info->flags & SHARE_MUX_CONF_REG)
 		pin_size = SHARE_FSL_PIN_SIZE;
 	else
 		pin_size = FSL_PIN_SIZE;
@@ -58,112 +60,127 @@ static int imx_pinctrl_set_state(struct udevice *dev, struct udevice *config)
 
 	npins = size / pin_size;
 
-	/*
-	 * Refer to linux documentation for details:
-	 * Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
-	 */
-	for (i = 0; i < npins; i++) {
-		mux_reg = pin_data[j++];
-
-		if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg)
-			mux_reg = -1;
-
-		if (info->flags & SHARE_MUX_CONF_REG) {
-			conf_reg = mux_reg;
-		} else {
-			conf_reg = pin_data[j++];
-			if (!(info->flags & ZERO_OFFSET_VALID) && !conf_reg)
-				conf_reg = -1;
-		}
+	if (info->flags & IMX8_USE_SCU) {
+		imx_pinctrl_scu_conf_pins(info, pin_data, npins);
+	} else {
+		/*
+		 * Refer to linux documentation for details:
+		 * Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
+		 */
+		for (i = 0; i < npins; i++) {
+			mux_reg = pin_data[j++];
 
-		if ((mux_reg == -1) || (conf_reg == -1)) {
-			dev_err(dev, "Error mux_reg or conf_reg\n");
-			devm_kfree(dev, pin_data);
-			return -EINVAL;
-		}
+			if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg)
+				mux_reg = -1;
 
-		input_reg = pin_data[j++];
-		mux_mode = pin_data[j++];
-		input_val = pin_data[j++];
-		config_val = pin_data[j++];
+			if (info->flags & SHARE_MUX_CONF_REG) {
+				conf_reg = mux_reg;
+			} else {
+				conf_reg = pin_data[j++];
+				if (!(info->flags & ZERO_OFFSET_VALID) &&
+				    !conf_reg)
+					conf_reg = -1;
+			}
 
-		dev_dbg(dev, "mux_reg 0x%x, conf_reg 0x%x, input_reg 0x%x, "
-			"mux_mode 0x%x, input_val 0x%x, config_val 0x%x\n",
-			mux_reg, conf_reg, input_reg, mux_mode, input_val,
-			config_val);
+			if ((mux_reg == -1) || (conf_reg == -1)) {
+				dev_err(dev, "Error mux_reg or conf_reg\n");
+				devm_kfree(dev, pin_data);
+				return -EINVAL;
+			}
 
-		if (config_val & IMX_PAD_SION)
-			mux_mode |= IOMUXC_CONFIG_SION;
+			input_reg = pin_data[j++];
+			mux_mode = pin_data[j++];
+			input_val = pin_data[j++];
+			config_val = pin_data[j++];
 
-		config_val &= ~IMX_PAD_SION;
+			dev_dbg(dev, "mux_reg 0x%x, conf_reg 0x%x, "
+				"input_reg 0x%x, mux_mode 0x%x, "
+				"input_val 0x%x, config_val 0x%x\n",
+				mux_reg, conf_reg, input_reg, mux_mode,
+				input_val, config_val);
 
-		/* Set Mux */
-		if (info->flags & SHARE_MUX_CONF_REG) {
-			clrsetbits_le32(info->base + mux_reg, info->mux_mask,
-					mux_mode << mux_shift);
-		} else {
-			writel(mux_mode, info->base + mux_reg);
-		}
+			if (config_val & IMX_PAD_SION)
+				mux_mode |= IOMUXC_CONFIG_SION;
 
-		dev_dbg(dev, "write mux: offset 0x%x val 0x%x\n", mux_reg,
-			mux_mode);
+			config_val &= ~IMX_PAD_SION;
 
-		/*
-		 * Set select input
-		 *
-		 * If the select input value begins with 0xff, it's a quirky
-		 * select input and the value should be interpreted as below.
-		 *     31     23      15      7        0
-		 *     | 0xff | shift | width | select |
-		 * It's used to work around the problem that the select
-		 * input for some pin is not implemented in the select
-		 * input register but in some general purpose register.
-		 * We encode the select input value, width and shift of
-		 * the bit field into input_val cell of pin function ID
-		 * in device tree, and then decode them here for setting
-		 * up the select input bits in general purpose register.
-		 */
+			/* Set Mux */
+			if (info->flags & SHARE_MUX_CONF_REG) {
+				clrsetbits_le32(info->base + mux_reg,
+						info->mux_mask,
+						mux_mode << mux_shift);
+			} else {
+				writel(mux_mode, info->base + mux_reg);
+			}
+
+			dev_dbg(dev, "write mux: offset 0x%x val 0x%x\n",
+				mux_reg, mux_mode);
 
-		if (input_val >> 24 == 0xff) {
-			u32 val = input_val;
-			u8 select = val & 0xff;
-			u8 width = (val >> 8) & 0xff;
-			u8 shift = (val >> 16) & 0xff;
-			u32 mask = ((1 << width) - 1) << shift;
-			/*
-			 * The input_reg[i] here is actually some IOMUXC general
-			 * purpose register, not regular select input register.
-			 */
-			val = readl(info->base + input_reg);
-			val &= ~mask;
-			val |= select << shift;
-			writel(val, info->base + input_reg);
-		} else if (input_reg) {
 			/*
-			 * Regular select input register can never be at offset
-			 * 0, and we only print register value for regular case.
+			 * Set select input
+			 *
+			 * If the select input value begins with 0xff,
+			 * it's a quirky select input and the value should
+			 * be interpreted as below.
+			 *     31     23      15      7        0
+			 *     | 0xff | shift | width | select |
+			 * It's used to work around the problem that the
+			 * select input for some pin is not implemented in
+			 * the select input register but in some general
+			 * purpose register. We encode the select input
+			 * value, width and shift of the bit field into
+			 * input_val cell of pin function ID in device tree,
+			 * and then decode them here for setting up the select
+			 * input bits in general purpose register.
 			 */
-			if (info->input_sel_base)
-				writel(input_val, info->input_sel_base +
-				       input_reg);
-			else
-				writel(input_val, info->base + input_reg);
-
-			dev_dbg(dev, "select_input: offset 0x%x val 0x%x\n",
-				input_reg, input_val);
-		}
 
-		/* Set config */
-		if (!(config_val & IMX_NO_PAD_CTL)) {
-			if (info->flags & SHARE_MUX_CONF_REG) {
-				clrsetbits_le32(info->base + conf_reg,
-						~info->mux_mask, config_val);
-			} else {
-				writel(config_val, info->base + conf_reg);
+			if (input_val >> 24 == 0xff) {
+				u32 val = input_val;
+				u8 select = val & 0xff;
+				u8 width = (val >> 8) & 0xff;
+				u8 shift = (val >> 16) & 0xff;
+				u32 mask = ((1 << width) - 1) << shift;
+				/*
+				 * The input_reg[i] here is actually some
+				 * IOMUXC general purpose register, not
+				 * regular select input register.
+				 */
+				val = readl(info->base + input_reg);
+				val &= ~mask;
+				val |= select << shift;
+				writel(val, info->base + input_reg);
+			} else if (input_reg) {
+				/*
+				 * Regular select input register can never be
+				 * at offset 0, and we only print register
+				 * value for regular case.
+				 */
+				if (info->input_sel_base)
+					writel(input_val,
+					       info->input_sel_base +
+					       input_reg);
+				else
+					writel(input_val,
+					       info->base + input_reg);
+
+				dev_dbg(dev, "select_input: offset 0x%x val "
+					"0x%x\n", input_reg, input_val);
 			}
 
-			dev_dbg(dev, "write config: offset 0x%x val 0x%x\n",
-				conf_reg, config_val);
+			/* Set config */
+			if (!(config_val & IMX_NO_PAD_CTL)) {
+				if (info->flags & SHARE_MUX_CONF_REG) {
+					clrsetbits_le32(info->base + conf_reg,
+							~info->mux_mask,
+							config_val);
+				} else {
+					writel(config_val,
+					       info->base + conf_reg);
+				}
+
+				dev_dbg(dev, "write config: offset 0x%x val "
+					"0x%x\n", conf_reg, config_val);
+			}
 		}
 	}
 
@@ -193,6 +210,9 @@ int imx_pinctrl_probe(struct udevice *dev,
 	priv->dev = dev;
 	priv->info = info;
 
+	if (info->flags & IMX8_USE_SCU)
+		return 0;
+
 	addr = fdtdec_get_addr_size(gd->fdt_blob, dev_of_offset(dev), "reg",
 				    &size);
 
@@ -238,6 +258,9 @@ int imx_pinctrl_remove(struct udevice *dev)
 	struct imx_pinctrl_priv *priv = dev_get_priv(dev);
 	struct imx_pinctrl_soc_info *info = priv->info;
 
+	if (info->flags & IMX8_USE_SCU)
+		return 0;
+
 	if (info->input_sel_base)
 		unmap_sysmem(info->input_sel_base);
 	if (info->base)
diff --git a/drivers/pinctrl/nxp/pinctrl-imx.h b/drivers/pinctrl/nxp/pinctrl-imx.h
index b0032455b7..947975ee72 100644
--- a/drivers/pinctrl/nxp/pinctrl-imx.h
+++ b/drivers/pinctrl/nxp/pinctrl-imx.h
@@ -40,13 +40,29 @@ extern const struct pinctrl_ops imx_pinctrl_ops;
 #define FSL_PIN_SIZE		24
 #define SHARE_FSL_PIN_SIZE	20
 
+/* Each pin on imx8qm/qxp consists of 2 u32 PIN_FUNC_ID and 1 u32 CONFIG */
+#define SHARE_IMX8_PIN_SIZE	12
+
 #define SHARE_MUX_CONF_REG	0x1
 #define ZERO_OFFSET_VALID	0x2
 #define CONFIG_IBE_OBE		0x4
+#define IMX8_USE_SCU		0x8
 
 #define IOMUXC_CONFIG_SION	(0x1 << 4)
 
 int imx_pinctrl_probe(struct udevice *dev, struct imx_pinctrl_soc_info *info);
 
 int imx_pinctrl_remove(struct udevice *dev);
+
+#ifdef CONFIG_PINCTRL_IMX_SCU
+int imx_pinctrl_scu_conf_pins(struct imx_pinctrl_soc_info *info,
+			      u32 *pin_data, int npins);
+#else
+static inline int imx_pinctrl_scu_conf_pins(struct imx_pinctrl_soc_info *info,
+					    u32 *pin_data, int npins)
+{
+	return 0;
+}
+#endif
+
 #endif /* __DRIVERS_PINCTRL_IMX_H */
diff --git a/drivers/pinctrl/nxp/pinctrl-imx8.c b/drivers/pinctrl/nxp/pinctrl-imx8.c
new file mode 100644
index 0000000000..0738da0ebe
--- /dev/null
+++ b/drivers/pinctrl/nxp/pinctrl-imx8.c
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+#include <common.h>
+#include <dm/device.h>
+#include <dm/pinctrl.h>
+
+#include "pinctrl-imx.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct imx_pinctrl_soc_info imx8_pinctrl_soc_info = {
+	.flags = IMX8_USE_SCU,
+};
+
+static int imx8_pinctrl_probe(struct udevice *dev)
+{
+	struct imx_pinctrl_soc_info *info =
+		(struct imx_pinctrl_soc_info *)dev_get_driver_data(dev);
+
+	return imx_pinctrl_probe(dev, info);
+}
+
+static const struct udevice_id imx8_pinctrl_match[] = {
+	{ .compatible = "fsl,imx8qxp-iomuxc", .data = (ulong)&imx8_pinctrl_soc_info },
+	{ /* sentinel */ }
+};
+
+U_BOOT_DRIVER(imx8_pinctrl) = {
+	.name = "imx8_pinctrl",
+	.id = UCLASS_PINCTRL,
+	.of_match = of_match_ptr(imx8_pinctrl_match),
+	.probe = imx8_pinctrl_probe,
+	.remove = imx_pinctrl_remove,
+	.priv_auto_alloc_size = sizeof(struct imx_pinctrl_priv),
+	.ops = &imx_pinctrl_ops,
+	.flags = DM_FLAG_PRE_RELOC,
+};
diff --git a/drivers/pinctrl/nxp/pinctrl-scu.c b/drivers/pinctrl/nxp/pinctrl-scu.c
new file mode 100644
index 0000000000..aa11075e0a
--- /dev/null
+++ b/drivers/pinctrl/nxp/pinctrl-scu.c
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <linux/bitops.h>
+#include <asm/io.h>
+#include <asm/arch/sci/sci.h>
+#include <misc.h>
+
+#include "pinctrl-imx.h"
+
+#define PADRING_IFMUX_EN_SHIFT		31
+#define PADRING_IFMUX_EN_MASK		BIT(31)
+#define PADRING_GP_EN_SHIFT		30
+#define PADRING_GP_EN_MASK		BIT(30)
+#define PADRING_IFMUX_SHIFT		27
+#define PADRING_IFMUX_MASK		GENMASK(29, 27)
+
+static int imx_pinconf_scu_set(struct imx_pinctrl_soc_info *info, u32 pad,
+			       u32 mux, u32 val)
+{
+	int ret;
+
+	/*
+	 * Mux should be done in pmx set, but we do not have a good api
+	 * to handle that in scfw, so config it in pad conf func
+	 */
+
+	val |= PADRING_IFMUX_EN_MASK;
+	val |= PADRING_GP_EN_MASK;
+	val |= (mux << PADRING_IFMUX_SHIFT) & PADRING_IFMUX_MASK;
+
+	ret = sc_pad_set(-1, pad, val);
+	if (ret)
+		printf("%s %d\n", __func__, ret);
+
+	return 0;
+}
+
+int imx_pinctrl_scu_conf_pins(struct imx_pinctrl_soc_info *info, u32 *pin_data,
+			      int npins)
+{
+	int pin_id, mux, config_val;
+	int i, j = 0;
+	int ret;
+
+	/*
+	 * Refer to linux documentation for details:
+	 * Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
+	 */
+	for (i = 0; i < npins; i++) {
+		pin_id = pin_data[j++];
+		mux = pin_data[j++];
+		config_val = pin_data[j++];
+
+		ret = imx_pinconf_scu_set(info, pin_id, mux, config_val);
+		if (ret)
+			printf("Set pin %d, mux %d, val %d, error\n", pin_id,
+			       mux, config_val);
+	}
+
+	return 0;
+}