drivers/i2c/fsl_i2c: modify i2c_read to handle multi-byte write

Most of the I2C slaves support accesses in the typical style
that is : read/write series of bytes at particular address offset.
These transactions look like:"
(1) START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"

However there are certain devices which support accesses in
terms of the transactions as follows:
(2) "START:Address:Tx:Txdata[0..n1]:Clock_stretching:
        RESTART:Address:Rx:data[0..n2]"
Here Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.

Type (1) transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.

To handle type (2) along with type (1) transactions,
i2c_read() function has been modified.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>

1 files changed, 34 insertions, 7 deletions

diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c
index 291ad946db..aa159f8d41 100644
--- a/drivers/i2c/fsl_i2c.c
+++ b/drivers/i2c/fsl_i2c.c
@@ -423,18 +423,45 @@ fsl_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, int alen, u8 *data,
 	struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
 	int i = -1; /* signal error */
 	u8 *a = (u8*)&addr;
+	int len = alen * -1;
 
 	if (i2c_wait4bus(adap) < 0)
 		return -1;
 
-	if ((!length || alen > 0)
-	    && i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0
-	    && __i2c_write(adap, &a[4 - alen], alen) == alen)
-		i = 0; /* No error so far */
+	/* To handle the need of I2C devices that require to write few bytes
+	 * (more than 4 bytes of address as in the case of else part)
+	 * of data before reading, Negative equivalent of length(bytes to write)
+	 * is passed, but used the +ve part of len for writing data
+	 */
+	if (alen < 0) {
+		/* Generate a START and send the Address and
+		 * the Tx Bytes to the slave.
+		 * "START: Address: Write bytes data[len]"
+		 * IF part supports writing any number of bytes in contrast
+		 * to the else part, which supports writing address offset
+		 * of upto 4 bytes only.
+		 * bytes that need to be written are passed in
+		 * "data", which will eventually keep the data READ,
+		 * after writing the len bytes out of it
+		 */
+		if (i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0)
+			i = __i2c_write(adap, data, len);
+
+		if (i != len)
+			return -1;
 
-	if (length &&
-	    i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0)
-		i = __i2c_read(adap, data, length);
+		if (length && i2c_write_addr(adap, dev, I2C_READ_BIT, 1) != 0)
+			i = __i2c_read(adap, data, length);
+	} else {
+		if ((!length || alen > 0) &&
+		    i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0  &&
+		    __i2c_write(adap, &a[4 - alen], alen) == alen)
+			i = 0; /* No error so far */
+
+		if (length &&
+		    i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0)
+			i = __i2c_read(adap, data, length);
+	}
 
 	writeb(I2C_CR_MEN, &device->cr);