diff options
| author | Matthias Fuchs <matthias.fuchs@esd-electronics.com> | 2009-04-29 09:50:57 +0200 |
|---|---|---|
| committer | Wolfgang Denk <wd@denx.de> | 2009-06-12 20:39:46 +0200 |
| commit | 7cc635fb35f5b94e304fa2243d56758f57f6416b (patch) | |
| tree | 73cadf4ddb7ec3deb1430fe752c1ca089adb04ed /include/configs/CMS700.h | |
| parent | c1b2f79788deec75773b1d944d8aaf4a6d5baf9e (diff) | |
4xx: Remove binary cpld bitstream from CMS700 board
This patch removes the cpld binary bitstream that is
used by esd's cpld command on CMS700 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Diffstat (limited to 'include/configs/CMS700.h')
| -rw-r--r-- | include/configs/CMS700.h | 53 |
1 files changed, 5 insertions, 48 deletions
diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h index 40fef88f98..ae8494d577 100644 --- a/include/configs/CMS700.h +++ b/include/configs/CMS700.h @@ -80,8 +80,6 @@ #define CONFIG_CMD_DHCP #define CONFIG_CMD_BSP -#define CONFIG_CMD_PCI -#define CONFIG_CMD_IRQ #define CONFIG_CMD_ELF #define CONFIG_CMD_NAND #define CONFIG_CMD_I2C @@ -167,31 +165,6 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ -#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is @@ -222,21 +195,16 @@ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#if 0 /* test-only */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ -#endif - /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (~(TEXT_BASE) + 1) +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) #if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM) # define CONFIG_SYS_RAMBOOT 1 @@ -291,8 +259,7 @@ /*----------------------------------------------------------------------- * FPGA stuff */ -#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */ -#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */ +#define CONFIG_SYS_XSVF_DEFAULT_ADDR 0xfffc0000 /* FPGA program pin configuration */ #define CONFIG_SYS_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */ @@ -356,17 +323,7 @@ * Default speed selection (cpu_plb_opb_ebc) in mhz. * This value will be set if iic boot eprom is disabled. */ -#if 0 -#define PLLMR0_DEFAULT PLLMR0_266_133_66_33 -#define PLLMR1_DEFAULT PLLMR1_266_133_66_33 -#endif -#if 0 -#define PLLMR0_DEFAULT PLLMR0_200_100_50_33 -#define PLLMR1_DEFAULT PLLMR1_200_100_50_33 -#endif -#if 1 #define PLLMR0_DEFAULT PLLMR0_133_66_66_33 #define PLLMR1_DEFAULT PLLMR1_133_66_66_33 -#endif #endif /* __CONFIG_H */ |