diff options
author | stroese <stroese> | 2004-12-16 18:05:42 +0000 |
---|---|---|
committer | stroese <stroese> | 2004-12-16 18:05:42 +0000 |
commit | a20b27a36b7b1f593e18b4efd506e5f01a392dc6 (patch) | |
tree | f9dc45c287966bb96c38a8267d07b217727efb3c /include/configs/CPCI405AB.h | |
parent | 44acc8d334a8b9ddb81fc238b094574991f19afa (diff) |
esd config files updated
Diffstat (limited to 'include/configs/CPCI405AB.h')
-rw-r--r-- | include/configs/CPCI405AB.h | 45 |
1 files changed, 25 insertions, 20 deletions
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index 3c94ebc349..dee26f8716 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -41,27 +41,22 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ +#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */ #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ -#if 0 -#define CONFIG_PREBOOT \ - "crc32 f0207004 ffc 0;" \ - "if cmp 0 f0207000 1;" \ - "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \ - "else;echo Old CRC is bad;fi" -#endif - #undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND "bootm 100000" /* default boot command */ +#undef CONFIG_BOOTCOMMAND + +#define CONFIG_PREBOOT /* enable preboot variable */ #undef CONFIG_LOADS_ECHO /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ @@ -75,6 +70,7 @@ CFG_CMD_PCI | \ CFG_CMD_IRQ | \ CFG_CMD_IDE | \ + CFG_CMD_FAT | \ CFG_CMD_ELF | \ CFG_CMD_DATE | \ CFG_CMD_JFFS2 | \ @@ -86,6 +82,8 @@ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION +#define CONFIG_SUPPORT_VFAT + /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -155,6 +153,8 @@ #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ +#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ + #define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ #define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ @@ -232,13 +232,14 @@ * I2C EEPROM (CAT24WC32) for environment */ #define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ #define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01 +#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom used! */ #define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ /* 32 byte page write mode using*/ /* last 5 bits of the address */ @@ -254,7 +255,7 @@ #define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ #define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ -#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */ +#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/ /*----------------------------------------------------------------------- * Cache Configuration @@ -331,16 +332,20 @@ #define CFG_FPGA_MODE_CF_RESET 0x0001 #define CFG_FPGA_MODE_DUART_RESET 0x0002 #define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */ -#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100 -#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000 -#define CFG_FPGA_MODE_TS_CLEAR 0x2000 +#define CFG_FPGA_MODE_1WIRE_DIR 0x0100 /* dir=1 -> output */ +#define CFG_FPGA_MODE_SIM_OK_DIR 0x0200 +#define CFG_FPGA_MODE_TESTRIG_FAIL_DIR 0x0400 +#define CFG_FPGA_MODE_1WIRE 0x1000 +#define CFG_FPGA_MODE_SIM_OK 0x2000 /* wired-or net from all devices */ +#define CFG_FPGA_MODE_TESTRIG_FAIL 0x4000 /* FPGA Status Reg */ -#define CFG_FPGA_STATUS_DIP0 0x0001 -#define CFG_FPGA_STATUS_DIP1 0x0002 -#define CFG_FPGA_STATUS_DIP2 0x0004 -#define CFG_FPGA_STATUS_FLASH 0x0008 -#define CFG_FPGA_STATUS_TS_IRQ 0x1000 +#define CFG_FPGA_STATUS_DIP0 0x0001 +#define CFG_FPGA_STATUS_DIP1 0x0002 +#define CFG_FPGA_STATUS_DIP2 0x0004 +#define CFG_FPGA_STATUS_FLASH 0x0008 +#define CFG_FPGA_STATUS_1WIRE 0x1000 +#define CFG_FPGA_STATUS_SIM_OK 0x2000 #define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ #define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */ |