rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 172 insertions, 172 deletions

diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index 256f15665a..aeb61a9d53 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -47,7 +47,7 @@
  * if CLKIN is 66MHz, then
  * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz
  */
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_SVCOD_DIV_2 |\
@@ -55,7 +55,7 @@
 	HRCWL_CORE_TO_CSB_1_5X1)
 
 #ifdef CONFIG_PCISLAVE
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_AGENT |\
 	HRCWH_PCI1_ARBITER_DISABLE |\
 	HRCWH_CORE_ENABLE |\
@@ -69,7 +69,7 @@
 	HRCWH_BIG_ENDIAN |\
 	HRCWH_LDP_CLEAR)
 #else
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
 	HRCWH_CORE_ENABLE |\
@@ -85,29 +85,29 @@
 #endif
 
 /* Arbiter Configuration Register */
-#define CFG_ACR_PIPE_DEP	3	/* Arbiter pipeline depth is 4 */
-#define CFG_ACR_RPTCNT		3	/* Arbiter repeat count is 4 */
+#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count is 4 */
 
 /* System Priority Control Register */
-#define CFG_SPCR_TSECEP		3	/* eTSEC1/2 emergency has highest priority */
+#define CONFIG_SYS_SPCR_TSECEP		3	/* eTSEC1/2 emergency has highest priority */
 
 /*
  * IP blocks clock configuration
  */
-#define CFG_SCCR_TSEC1CM	1	/* CSB:eTSEC1 = 1:1 */
-#define CFG_SCCR_TSEC2CM	1	/* CSB:eTSEC2 = 1:1 */
-#define CFG_SCCR_SATACM		SCCR_SATACM_2	/* CSB:SATA[0:3] = 2:1 */
+#define CONFIG_SYS_SCCR_TSEC1CM	1	/* CSB:eTSEC1 = 1:1 */
+#define CONFIG_SYS_SCCR_TSEC2CM	1	/* CSB:eTSEC2 = 1:1 */
+#define CONFIG_SYS_SCCR_SATACM		SCCR_SATACM_2	/* CSB:SATA[0:3] = 2:1 */
 
 /*
  * System IO Config
  */
-#define CFG_SICRH		0x00000000
-#define CFG_SICRL		0x00000000
+#define CONFIG_SYS_SICRH		0x00000000
+#define CONFIG_SYS_SICRL		0x00000000
 
 /*
  * Output Buffer Impedance
  */
-#define CFG_OBIR		0x31100000
+#define CONFIG_SYS_OBIR		0x31100000
 
 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
 #define CONFIG_BOARD_EARLY_INIT_R
@@ -115,17 +115,17 @@
 /*
  * IMMR new address
  */
-#define CFG_IMMR		0xE0000000
+#define CONFIG_SYS_IMMR		0xE0000000
 
 /*
  * DDR Setup
  */
-#define CFG_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE		CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE
-#define CFG_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CFG_83XX_DDR_USES_CS0
-#define CFG_DDRCDR_VALUE	0x80080001 /* ODT 150ohm on SoC */
+#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_83XX_DDR_USES_CS0
+#define CONFIG_SYS_DDRCDR_VALUE	0x80080001 /* ODT 150ohm on SoC */
 
 #undef CONFIG_DDR_ECC		/* support DDR ECC function */
 #undef CONFIG_DDR_ECC_CMD	/* Use DDR ECC user commands */
@@ -141,14 +141,14 @@
  * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM
  * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5
  */
-#define CFG_DDR_SIZE		512 /* MB */
-#define CFG_DDR_CS0_BNDS	0x0000001f
-#define CFG_DDR_CS0_CONFIG	( CSCONFIG_EN \
+#define CONFIG_SYS_DDR_SIZE		512 /* MB */
+#define CONFIG_SYS_DDR_CS0_BNDS	0x0000001f
+#define CONFIG_SYS_DDR_CS0_CONFIG	( CSCONFIG_EN \
 				| 0x00010000  /* ODT_WR to CSn */ \
 				| CSCONFIG_ROW_BIT_14 | CSCONFIG_COL_BIT_10 )
 				/* 0x80010202 */
-#define CFG_DDR_TIMING_3	0x00000000
-#define CFG_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
@@ -157,7 +157,7 @@
 				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
 				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
 				/* 0x00620802 */
-#define CFG_DDR_TIMING_1	( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_1	( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
 				| ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
 				| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
 				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
@@ -166,7 +166,7 @@
 				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
 				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
 				/* 0x3935d322 */
-#define CFG_DDR_TIMING_2	( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_2	( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
 				| ( 6 << TIMING_CFG2_CPO_SHIFT ) \
 				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
 				| ( 4 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
@@ -174,70 +174,70 @@
 				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
 				| ( 8 << TIMING_CFG2_FOUR_ACT_SHIFT) )
 				/* 0x131088c8 */
-#define CFG_DDR_INTERVAL	( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+#define CONFIG_SYS_DDR_INTERVAL	( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \
 				| ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
 				/* 0x03E00100 */
-#define CFG_DDR_SDRAM_CFG	0x43000000
-#define CFG_DDR_SDRAM_CFG2	0x00001000 /* 1 posted refresh */
-#define CFG_DDR_MODE		( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \
+#define CONFIG_SYS_DDR_SDRAM_CFG	0x43000000
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00001000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE		( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \
 				| ( 0x1432 << SDRAM_MODE_SD_SHIFT ) )
 				/* ODT 150ohm CL=3, AL=1 on SDRAM */
-#define CFG_DDR_MODE2		0x00000000
+#define CONFIG_SYS_DDR_MODE2		0x00000000
 #endif
 
 /*
  * Memory test
  */
-#undef CFG_DRAM_TEST		/* memory test, takes time */
-#define CFG_MEMTEST_START	0x00040000 /* memtest region */
-#define CFG_MEMTEST_END		0x00140000
+#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START	0x00040000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x00140000
 
 /*
  * The reserved memory
  */
-#define CFG_MONITOR_BASE	TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE /* start of monitor */
 
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
 #else
-#undef CFG_RAMBOOT
+#undef CONFIG_SYS_RAMBOOT
 #endif
 
-/* CFG_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN		(512 * 1024) /* Reserved for malloc */
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(512 * 1024) /* Reserved for malloc */
 
 /*
  * Initial RAM Base Address Setup
  */
-#define CFG_INIT_RAM_LOCK	1
-#define CFG_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END	0x1000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE	0x100 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END	0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 
 /*
  * Local Bus Configuration & Clock Setup
  */
-#define CFG_LCRR		(LCRR_DBYP | LCRR_CLKDIV_8)
-#define CFG_LBC_LBCR		0x00000000
+#define CONFIG_SYS_LCRR		(LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LBC_LBCR		0x00000000
 
 /*
  * FLASH on the Local Bus
  */
-#define CFG_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
 #define CONFIG_FLASH_CFI_DRIVER	/* use the CFI driver */
-#define CFG_FLASH_BASE		0xFE000000 /* FLASH base address */
-#define CFG_FLASH_SIZE		32 /* max FLASH size is 32M */
-#define CFG_FLASH_PROTECTION	1		/* Use h/w Flash protection. */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE		32 /* max FLASH size is 32M */
+#define CONFIG_SYS_FLASH_PROTECTION	1		/* Use h/w Flash protection. */
 
-#define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE /* Window base at flash base */
-#define CFG_LBLAWAR0_PRELIM	0x80000018 /* 32MB window size */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE /* Window base at flash base */
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000018 /* 32MB window size */
 
-#define CFG_BR0_PRELIM		( CFG_FLASH_BASE	/* Flash Base address */ \
+#define CONFIG_SYS_BR0_PRELIM		( CONFIG_SYS_FLASH_BASE	/* Flash Base address */ \
 				| (2 << BR_PS_SHIFT)	/* 16 bit port size */ \
 				| BR_V )		/* valid */
-#define CFG_OR0_PRELIM		( (~(CFG_FLASH_SIZE - 1) << 20) \
+#define CONFIG_SYS_OR0_PRELIM		( (~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
 				| OR_UPM_XAM \
 				| OR_GPCM_CSNT \
 				| OR_GPCM_ACS_DIV2 \
@@ -248,33 +248,33 @@
 				| OR_GPCM_EAD )
 				/* 0xFE000FF7 */
 
-#define CFG_MAX_FLASH_BANKS	1 /* number of banks */
-#define CFG_MAX_FLASH_SECT	256 /* max sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	256 /* max sectors per device */
 
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
 
 /*
  * BCSR on the Local Bus
  */
-#define CFG_BCSR		0xF8000000
-#define CFG_LBLAWBAR1_PRELIM	CFG_BCSR /* Access window base at BCSR base */
-#define CFG_LBLAWAR1_PRELIM	0x8000000E /* Access window size 32K */
+#define CONFIG_SYS_BCSR		0xF8000000
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_BCSR /* Access window base at BCSR base */
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E /* Access window size 32K */
 
-#define CFG_BR1_PRELIM		(CFG_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */
-#define CFG_OR1_PRELIM		0xFFFFE9f7 /* length 32K */
+#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */
+#define CONFIG_SYS_OR1_PRELIM		0xFFFFE9f7 /* length 32K */
 
 /*
  * NAND Flash on the Local Bus
  */
-#define CFG_NAND_BASE		0xE0600000	/* 0xE0600000 */
-#define CFG_BR3_PRELIM		( CFG_NAND_BASE \
+#define CONFIG_SYS_NAND_BASE		0xE0600000	/* 0xE0600000 */
+#define CONFIG_SYS_BR3_PRELIM		( CONFIG_SYS_NAND_BASE \
 				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
 				| BR_PS_8		/* Port Size = 8 bit */ \
 				| BR_MS_FCM		/* MSEL = FCM */ \
 				| BR_V )		/* valid */
-#define CFG_OR3_PRELIM		( 0xFFFF8000		/* length 32K */ \
+#define CONFIG_SYS_OR3_PRELIM		( 0xFFFF8000		/* length 32K */ \
 				| OR_FCM_CSCT \
 				| OR_FCM_CST \
 				| OR_FCM_CHT \
@@ -283,29 +283,29 @@
 				| OR_FCM_EHTR )
 				/* 0xFFFF8396 */
 
-#define CFG_LBLAWBAR3_PRELIM	CFG_NAND_BASE
-#define CFG_LBLAWAR3_PRELIM	0x8000000E	/* 32KB  */
+#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E	/* 32KB  */
 
 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE	1
-#define CFG_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
 
-#define CFG_BAUDRATE_TABLE  \
+#define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
-#define CFG_NS16550_COM1	(CFG_IMMR+0x4500)
-#define CFG_NS16550_COM2	(CFG_IMMR+0x4600)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
 
 /* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* Pass open firmware flat tree */
@@ -317,35 +317,35 @@
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
 #undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
-#define CFG_I2C_SPEED		400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES	{0x51} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET		0x3000
-#define CFG_I2C2_OFFSET		0x3100
+#define CONFIG_SYS_I2C_SPEED		400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{0x51} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
 
 /*
  * Config on-board RTC
  */
 #define CONFIG_RTC_DS1374	/* use ds1374 rtc via i2c */
-#define CFG_I2C_RTC_ADDR	0x68 /* at address 0x68 */
+#define CONFIG_SYS_I2C_RTC_ADDR	0x68 /* at address 0x68 */
 
 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
-#define CFG_PCI_MEM_BASE	0x80000000
-#define CFG_PCI_MEM_PHYS	CFG_PCI_MEM_BASE
-#define CFG_PCI_MEM_SIZE	0x10000000 /* 256M */
-#define CFG_PCI_MMIO_BASE	0x90000000
-#define CFG_PCI_MMIO_PHYS	CFG_PCI_MMIO_BASE
-#define CFG_PCI_MMIO_SIZE	0x10000000 /* 256M */
-#define CFG_PCI_IO_BASE		0x00000000
-#define CFG_PCI_IO_PHYS		0xE0300000
-#define CFG_PCI_IO_SIZE		0x100000 /* 1M */
+#define CONFIG_SYS_PCI_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI_MEM_PHYS	CONFIG_SYS_PCI_MEM_BASE
+#define CONFIG_SYS_PCI_MEM_SIZE	0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI_MMIO_PHYS	CONFIG_SYS_PCI_MMIO_BASE
+#define CONFIG_SYS_PCI_MMIO_SIZE	0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI_IO_PHYS		0xE0300000
+#define CONFIG_SYS_PCI_IO_SIZE		0x100000 /* 1M */
 
-#define CFG_PCI_SLV_MEM_LOCAL	CFG_SDRAM_BASE
-#define CFG_PCI_SLV_MEM_BUS	0x00000000
-#define CFG_PCI_SLV_MEM_SIZE	0x80000000
+#define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
+#define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000
 
 #ifdef CONFIG_PCI
 #define CONFIG_83XX_GENERIC_PCI	1 /* Use generic PCI setup */
@@ -356,7 +356,7 @@
 
 #undef CONFIG_EEPRO100
 #undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
 #endif /* CONFIG_PCI */
 
 #ifndef CONFIG_NET_MULTI
@@ -367,10 +367,10 @@
  * TSEC
  */
 #define CONFIG_TSEC_ENET	/* TSEC ethernet support */
-#define CFG_TSEC1_OFFSET	0x24000
-#define CFG_TSEC1		(CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET	0x25000
-#define CFG_TSEC2		(CFG_IMMR+CFG_TSEC2_OFFSET)
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define CONFIG_SYS_TSEC1		(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET	0x25000
+#define CONFIG_SYS_TSEC2		(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 
 /*
  * TSEC ethernet configuration
@@ -401,15 +401,15 @@
 #define CONFIG_LIBATA
 #define CONFIG_FSL_SATA
 
-#define CFG_SATA_MAX_DEVICE	2
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_SATA1
-#define CFG_SATA1_OFFSET	0x18000
-#define CFG_SATA1		(CFG_IMMR + CFG_SATA1_OFFSET)
-#define CFG_SATA1_FLAGS		FLAGS_DMA
+#define CONFIG_SYS_SATA1_OFFSET	0x18000
+#define CONFIG_SYS_SATA1		(CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
 #define CONFIG_SATA2
-#define CFG_SATA2_OFFSET	0x19000
-#define CFG_SATA2		(CFG_IMMR + CFG_SATA2_OFFSET)
-#define CFG_SATA2_FLAGS		FLAGS_DMA
+#define CONFIG_SYS_SATA2_OFFSET	0x19000
+#define CONFIG_SYS_SATA2		(CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
+#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
 
 #ifdef CONFIG_FSL_SATA
 #define CONFIG_LBA48
@@ -421,20 +421,20 @@
 /*
  * Environment
  */
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
 	#define CONFIG_ENV_IS_IN_FLASH	1
-	#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 	#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
 	#define CONFIG_ENV_SIZE		0x2000
 #else
-	#define CFG_NO_FLASH		1	/* Flash is not usable now */
+	#define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
 	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
-	#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 	#define CONFIG_ENV_SIZE		0x2000
 #endif
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
 /*
  * BOOTP options
@@ -459,7 +459,7 @@
     #define CONFIG_CMD_PCI
 #endif
 
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
     #undef CONFIG_CMD_ENV
     #undef CONFIG_CMD_LOADS
 #endif
@@ -471,34 +471,34 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP		/* undef to save memory */
-#define CFG_LOAD_ADDR		0x2000000 /* default load address */
-#define CFG_PROMPT		"=> "	/* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt */
 
 #if defined(CONFIG_CMD_KGDB)
-	#define CFG_CBSIZE	1024 /* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
 #else
-	#define CFG_CBSIZE	256 /* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	256 /* Console I/O Buffer Size */
 #endif
 
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args */
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
-#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
 
 /*
  * Core HID Setup
  */
-#define CFG_HID0_INIT		0x000000000
-#define CFG_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
-#define CFG_HID2		HID2_HBE
+#define CONFIG_SYS_HID0_INIT		0x000000000
+#define CONFIG_SYS_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID2		HID2_HBE
 
 /*
  * MMU Setup
@@ -506,67 +506,67 @@
 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
 
 /* DDR: cache cacheable */
-#define CFG_SDRAM_LOWER		CFG_SDRAM_BASE
-#define CFG_SDRAM_UPPER		(CFG_SDRAM_BASE + 0x10000000)
+#define CONFIG_SYS_SDRAM_LOWER		CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_SDRAM_UPPER		(CONFIG_SYS_SDRAM_BASE + 0x10000000)
 
-#define CFG_IBAT0L	(CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U	(CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT0L	CFG_IBAT0L
-#define CFG_DBAT0U	CFG_IBAT0U
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
 
-#define CFG_IBAT1L	(CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U	(CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT1L	CFG_IBAT1L
-#define CFG_DBAT1U	CFG_IBAT1U
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
 
 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CFG_IBAT2L	(CFG_IMMR | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT2U	(CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
-#define CFG_DBAT2L	CFG_IBAT2L
-#define CFG_DBAT2U	CFG_IBAT2U
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
 
 /* BCSR: cache-inhibit and guarded */
-#define CFG_IBAT3L	(CFG_BCSR | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_BCSR | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT3U	(CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_DBAT3L	CFG_IBAT3L
-#define CFG_DBAT3U	CFG_IBAT3U
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_BCSR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
 
 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CFG_IBAT4L	(CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT4U	(CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_DBAT4L	(CFG_FLASH_BASE | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U	CFG_IBAT4U
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
 
 /* Stack in dcache: cacheable, no memory coherence */
-#define CFG_IBAT5L	(CFG_INIT_RAM_ADDR | BATL_PP_10)
-#define CFG_IBAT5U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_DBAT5L	CFG_IBAT5L
-#define CFG_DBAT5U	CFG_IBAT5U
+#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
 
 #ifdef CONFIG_PCI
 /* PCI MEM space: cacheable */
-#define CFG_IBAT6L	(CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U	(CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT6L	CFG_IBAT6L
-#define CFG_DBAT6U	CFG_IBAT6U
+#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
 /* PCI MMIO space: cache-inhibit and guarded */
-#define CFG_IBAT7L	(CFG_PCI_MMIO_PHYS | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT7U	(CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT7L	CFG_IBAT7L
-#define CFG_DBAT7U	CFG_IBAT7U
+#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 #else
-#define CFG_IBAT6L	(0)
-#define CFG_IBAT6U	(0)
-#define CFG_IBAT7L	(0)
-#define CFG_IBAT7U	(0)
-#define CFG_DBAT6L	CFG_IBAT6L
-#define CFG_DBAT6U	CFG_IBAT6U
-#define CFG_DBAT7L	CFG_IBAT7L
-#define CFG_DBAT7U	CFG_IBAT7U
+#define CONFIG_SYS_IBAT6L	(0)
+#define CONFIG_SYS_IBAT6U	(0)
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 #endif
 
 /*