powerpc/p1010rdb: add p1010rdb-pb support with updating p1010rdb-pa

- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.

For more details, see board/freescale/p1010rdb/README.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>

1 files changed, 87 insertions, 14 deletions

diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index 032c078773..c6b9acac3b 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -120,7 +120,11 @@
 #endif
 
 /* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#if defined(CONFIG_P1010RDB_PA)
 #define CONFIG_SYS_PCIE2_NAME		"PCIe Slot"
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_SYS_PCIE2_NAME		"mini PCIe Slot"
+#endif
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
@@ -200,25 +204,24 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_DDR_INIT_ADDR	0x00000000
 #define CONFIG_SYS_DDR_INIT_EXT_ADDR	0x00000000
 #define CONFIG_SYS_DDR_MODE_CONTROL	0x00000000
-
 #define CONFIG_SYS_DDR_ZQ_CONTROL	0x89080600
 #define CONFIG_SYS_DDR_SR_CNTR		0x00000000
 #define CONFIG_SYS_DDR_RCW_1		0x00000000
 #define CONFIG_SYS_DDR_RCW_2		0x00000000
-#define CONFIG_SYS_DDR_CONTROL		0x470C0000	/* Type = DDR3  */
-#define CONFIG_SYS_DDR_CONTROL_2	0x04401010
+#define CONFIG_SYS_DDR_CONTROL		0xc70c0008      /* Type = DDR3  */
+#define CONFIG_SYS_DDR_CONTROL_2	0x24401000
 #define CONFIG_SYS_DDR_TIMING_4		0x00000001
 #define CONFIG_SYS_DDR_TIMING_5		0x03402400
 
-#define CONFIG_SYS_DDR_TIMING_3_800	0x00020000
-#define CONFIG_SYS_DDR_TIMING_0_800	0x00330004
-#define CONFIG_SYS_DDR_TIMING_1_800	0x6f6B4644
+#define CONFIG_SYS_DDR_TIMING_3_800	0x00030000
+#define CONFIG_SYS_DDR_TIMING_0_800	0x00110104
+#define CONFIG_SYS_DDR_TIMING_1_800	0x6f6b8644
 #define CONFIG_SYS_DDR_TIMING_2_800	0x0FA888CF
 #define CONFIG_SYS_DDR_CLK_CTRL_800	0x03000000
-#define CONFIG_SYS_DDR_MODE_1_800	0x40461520
-#define CONFIG_SYS_DDR_MODE_2_800	0x8000c000
+#define CONFIG_SYS_DDR_MODE_1_800	0x00441420
+#define CONFIG_SYS_DDR_MODE_2_800	0x00000000
 #define CONFIG_SYS_DDR_INTERVAL_800	0x0C300100
-#define CONFIG_SYS_DDR_WRLVL_CONTROL_800	0x8655A608
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
 
 /* settings for DDR3 at 667MT/s */
 #define CONFIG_SYS_DDR_TIMING_3_667		0x00010000
@@ -315,6 +318,8 @@ extern unsigned long get_sdram_size(void);
 				| CSPR_MSEL_NAND	\
 				| CSPR_V)
 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+
+#if defined(CONFIG_P1010RDB_PA)
 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
@@ -322,13 +327,26 @@ extern unsigned long get_sdram_size(void);
 				| CSOR_NAND_PGS_512	/* Page Size = 512b */ \
 				| CSOR_NAND_SPRZ_16	/* Spare size = 16 */ \
 				| CSOR_NAND_PB(32))	/* 32 Pages Per Block */
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 * 1024)
+
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_NAND_CSOR   (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
+				| CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
+				| CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
+				| CSOR_NAND_PB(128))  /*Pages Per Block = 128 */
+#define CONFIG_SYS_NAND_BLOCK_SIZE     (512 * 1024)
+#endif
 
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 * 1024)
 
+#if defined(CONFIG_P1010RDB_PA)
 /* NAND Flash Timing Params */
 #define CONFIG_SYS_NAND_FTIM0		FTIM0_NAND_TCCST(0x01) | \
 					FTIM0_NAND_TWP(0x0C)   | \
@@ -343,6 +361,23 @@ extern unsigned long get_sdram_size(void);
 					FTIM2_NAND_TWHRE(0x0f)
 #define CONFIG_SYS_NAND_FTIM3		FTIM3_NAND_TWW(0x04)
 
+#elif defined(CONFIG_P1010RDB_PB)
+/* support MT29F16G08ABABAWP 4k-pagesize 2G-bytes NAND */
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0  (FTIM0_NAND_TCCST(0x07)| \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1  (FTIM1_NAND_TADLE(0x32)| \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2  (FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a)  | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3	0x0
+#endif
+
 #define CONFIG_SYS_NAND_DDR_LAW		11
 
 /* Set up IFC registers for boot location NOR/NAND */
@@ -475,10 +510,20 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
 #define I2C_PCA9557_ADDR1		0x18
+#define I2C_PCA9557_ADDR2		0x19
 #define I2C_PCA9557_BUS_NUM		0
 
 /* I2C EEPROM */
-#undef CONFIG_ID_EEPROM
+#if defined(CONFIG_P1010RDB_PB)
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+#define MAX_NUM_PORTS			9 /* for 128Bytes EEPROM */
+#endif
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_MULTI_EEPROMS
@@ -602,9 +647,14 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_ENV_SIZE		0x2000
 #elif defined(CONFIG_NAND)
 #define CONFIG_ENV_IS_IN_NAND
+#if defined(CONFIG_P1010RDB_PA)
 #define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_RANGE	(3 * CONFIG_ENV_SIZE) /* 3*16=48K for env */
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_ENV_SIZE		(16 * 1024)
+#define CONFIG_ENV_RANGE	(32 * CONFIG_ENV_SIZE) /* new block size 512K */
+#endif
 #define CONFIG_ENV_OFFSET	((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_ENV_RANGE	(3 * CONFIG_ENV_SIZE)
 #elif defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_ENV_IS_NOWHERE		/* Store ENV in memory only */
 #define CONFIG_ENV_ADDR			(CONFIG_SYS_MONITOR_BASE - 0x1000)
@@ -697,7 +747,6 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_HAS_ETH2
 #endif
 
-#define CONFIG_HOSTNAME		P1010RDB
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	u-boot.bin/* U-Boot image on TFTP server */
@@ -736,7 +785,31 @@ extern unsigned long get_sdram_size(void);
 	"ext2load usb 0:4 $loadaddr $bootfile;"		\
 	"ext2load usb 0:4 $fdtaddr $fdtfile;"	\
 	"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"	\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr\0"		\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr\0"	\
+	CONFIG_BOOTMODE
+
+#if defined(CONFIG_P1010RDB_PA)
+#define CONFIG_BOOTMODE \
+	"boot_bank0=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
+	"mw.b ffb00011 0; mw.b ffb00009 0; reset\0" \
+	"boot_bank1=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
+	"mw.b ffb00011 0; mw.b ffb00009 1; reset\0" \
+	"boot_nand=i2c dev 0; i2c mw 18 1 f9; i2c mw 18 3 f0;" \
+	"mw.b ffb00011 0; mw.b ffb00017 1; reset\0"
+
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_BOOTMODE \
+	"boot_bank0=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
+	"i2c mw 19 1 2; i2c mw 19 3 e1; reset\0" \
+	"boot_bank1=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
+	"i2c mw 19 1 12; i2c mw 19 3 e1; reset\0" \
+	"boot_nand=i2c dev 0; i2c mw 18 1 fc; i2c mw 18 3 0;" \
+	"i2c mw 19 1 8; i2c mw 19 3 f7; reset\0" \
+	"boot_spi=i2c dev 0; i2c mw 18 1 fa; i2c mw 18 3 0;" \
+	"i2c mw 19 1 0; i2c mw 19 3 f7; reset\0" \
+	"boot_sd=i2c dev 0; i2c mw 18 1 f8; i2c mw 18 3 0;" \
+	"i2c mw 19 1 4; i2c mw 19 3 f3; reset\0"
+#endif
 
 #define CONFIG_RAMBOOTCOMMAND		\
 	"setenv bootargs root=/dev/ram rw "	\