rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 115 insertions, 115 deletions

diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 337cbfb1e2..675dbe6676 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -49,7 +49,7 @@
 
 #define CONFIG_PREBOOT                  /* enable preboot variable      */
 
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_NET_MULTI	1
 #undef  CONFIG_HAS_ETH1
@@ -103,53 +103,53 @@
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address		*/
+#define CONFIG_SYS_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 
-#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
-#ifdef	CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2	"> "
+#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
+#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
+#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
-#define CFG_BASE_BAUD	    691200
+#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CONFIG_SYS_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CONFIG_SYS_BASE_BAUD	    691200
 #undef	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE	\
+#define CONFIG_SYS_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
-#define CFG_LOAD_ADDR	0x100000	/* default load address */
-#define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
+#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
@@ -166,23 +166,23 @@
 
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
+#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 /*
  * NAND-FLASH stuff
  */
-#define CFG_NAND_BASE_LIST	{CFG_NAND_BASE}
+#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE}
 #define NAND_MAX_CHIPS          1
-#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
 #define NAND_BIG_DELAY_US	25
 
-#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
-#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
-#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
-#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+#define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
-#define CFG_NAND_QUIET          1
+#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CONFIG_SYS_NAND_QUIET          1
 
 /*
  * PCI stuff
@@ -200,15 +200,15 @@
 
 #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
 
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xf8000001      /* 128MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x08000000      /* Host: use this pci address   */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
+#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
+#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
+#define CONFIG_SYS_PCI_PTM1MS  0xf8000001      /* 128MB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
+#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
+#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
+#define CONFIG_SYS_PCI_PTM2PCI 0x08000000      /* Host: use this pci address   */
 
 /*
  * IDE/ATA stuff
@@ -217,58 +217,58 @@
 #undef	CONFIG_IDE_LED			/* no led for ide supported	*/
 #define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
 
-#define CFG_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
+#define CONFIG_SYS_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
 /* max. 1 drives per IDE bus */
-#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1)
+#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*1)
 
-#define CFG_ATA_BASE_ADDR	0xF0100000
-#define CFG_ATA_IDE0_OFFSET	0x0000
+#define CONFIG_SYS_ATA_BASE_ADDR	0xF0100000
+#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
 
-#define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register access */
-#define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET	0x0000	/* Offset for normal register access */
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
 
 /*
  * FLASH organization
  */
 #define FLASH_BASE0_PRELIM	0xFFC00000 /* FLASH bank #0 */
 
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms) */
 
-#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width) */
-#define CFG_FLASH_ADDR0		0x5555	/* 1st addr for flash config cycles */
-#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd addr for flash config cycles */
+#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width) */
+#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st addr for flash config cycles */
+#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd addr for flash config cycles */
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0		0x0000	/* 0 is standard */
-#define CFG_FLASH_READ1		0x0001	/* 1 is standard */
-#define CFG_FLASH_READ2		0x0002	/* 2 is standard */
+#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard */
+#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard */
+#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard */
 
-#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector */
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector */
 
 /*
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0xFFFA0000
-#define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384kB for Monitor */
-#define CFG_MALLOC_LEN		(384 * 1024)	/* Reserve 384kB for malloc() */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0xFFFA0000
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)	/* Reserve 384kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN		(384 * 1024)	/* Reserve 384kB for malloc() */
 
 /*
  * Environment Variable setup
@@ -281,20 +281,20 @@
  * I2C EEPROM (24WC16) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
-#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM 24WC16 */
-#define CFG_EEPROM_WREN         1
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM 24WC16 */
+#define CONFIG_SYS_EEPROM_WREN         1
 
 /* 24WC16 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"    */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The 24WC16 has   */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The 24WC16 has   */
 					/* 16 byte page write mode using */
 					/* last 4 bits of the address   */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 
 /*
  * External Bus Controller (EBC) Setup
@@ -304,69 +304,69 @@
 #define DUART1_BA	0xF0000408	    /* DUART Base Address       */
 #define RTC_BA		0xF0000500	    /* RTC Base Address         */
 #define VGA_BA		0xF1000000	    /* Epson VGA Base Address   */
-#define CFG_NAND_BASE	0xF4000000	    /* NAND FLASH Base Address  */
+#define CONFIG_SYS_NAND_BASE	0xF4000000	    /* NAND FLASH Base Address  */
 
 /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
 /* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0AP		0x92015480
+#define CONFIG_SYS_EBC_PB0AP		0x92015480
 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-#define CFG_EBC_PB0CR		0xFFC5A000
+#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000
 
 /* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP		0x92015480
+#define CONFIG_SYS_EBC_PB1AP		0x92015480
 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
-#define CFG_EBC_PB1CR		0xF4018000
+#define CONFIG_SYS_EBC_PB1CR		0xF4018000
 
 /* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2AP		0x010053C0
+#define CONFIG_SYS_EBC_PB2AP		0x010053C0
 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-#define CFG_EBC_PB2CR		0xF0018000
+#define CONFIG_SYS_EBC_PB2CR		0xF0018000
 
 /* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3AP		0x010053C0
+#define CONFIG_SYS_EBC_PB3AP		0x010053C0
 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CFG_EBC_PB3CR		0xF011A000
+#define CONFIG_SYS_EBC_PB3CR		0xF011A000
 
 /*
  * FPGA stuff
  */
-#define CFG_FPGA_BASE_ADDR 0xF0100100	    /* FPGA internal Base Address */
+#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100	    /* FPGA internal Base Address */
 
 /* FPGA internal regs */
-#define CFG_FPGA_CTRL		0x000
+#define CONFIG_SYS_FPGA_CTRL		0x000
 
 /* FPGA Control Reg */
-#define CFG_FPGA_CTRL_CF_RESET	0x0001
-#define CFG_FPGA_CTRL_WDI	0x0002
-#define CFG_FPGA_CTRL_PS2_RESET 0x0020
+#define CONFIG_SYS_FPGA_CTRL_CF_RESET	0x0001
+#define CONFIG_SYS_FPGA_CTRL_WDI	0x0002
+#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020
 
-#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/
+#define CONFIG_SYS_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now */
+#define CONFIG_SYS_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input) */
+#define CONFIG_SYS_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
+#define CONFIG_SYS_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output) */
+#define CONFIG_SYS_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output) */
+#define CONFIG_SYS_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input) */
+#define CONFIG_SYS_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input) */
 
 /*
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM	  1
+#define CONFIG_SYS_TEMP_STACK_OCM	  1
 
 /* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR	0xF8000000
-#define CFG_OCM_DATA_SIZE	0x1000
-#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM */
-#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM  */
+#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
+#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM  */
 
-#define CFG_GBL_DATA_SIZE      128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE      128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*
  * Definitions for GPIO setup (PPC405EP specific)
@@ -380,16 +380,16 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CFG_GPIO0_OSRH		0x00000550
-#define CFG_GPIO0_OSRL		0x00000110
-#define CFG_GPIO0_ISR1H		0x00000000
-#define CFG_GPIO0_ISR1L		0x15555445
-#define CFG_GPIO0_TSRH		0x00000000
-#define CFG_GPIO0_TSRL		0x00000000
-#define CFG_GPIO0_TCR		0x77FE0014
+#define CONFIG_SYS_GPIO0_OSRH		0x00000550
+#define CONFIG_SYS_GPIO0_OSRL		0x00000110
+#define CONFIG_SYS_GPIO0_ISR1H		0x00000000
+#define CONFIG_SYS_GPIO0_ISR1L		0x15555445
+#define CONFIG_SYS_GPIO0_TSRH		0x00000000
+#define CONFIG_SYS_GPIO0_TSRL		0x00000000
+#define CONFIG_SYS_GPIO0_TCR		0x77FE0014
 
-#define CFG_DUART_RST		(0x80000000 >> 14)
-#define CFG_EEPROM_WP		(0x80000000 >> 0)
+#define CONFIG_SYS_DUART_RST		(0x80000000 >> 14)
+#define CONFIG_SYS_EEPROM_WP		(0x80000000 >> 0)
 
 /*
  * Internal Definitions
@@ -421,9 +421,9 @@
  */
 #define CONFIG_USB_OHCI_NEW	1
 #define CONFIG_PCI_OHCI		1
-#define CFG_OHCI_SWAP_REG_ACCESS 1
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
-#define CFG_USB_OHCI_SLOT_NAME	"ohci_pci"
+#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
 #define CONFIG_USB_STORAGE	1
 
 #endif	/* __CONFIG_H */