Patch by Reinhard Meyer, 28 Dec 2003:

Add initial support for TOP5200 board

1 files changed, 291 insertions, 0 deletions

diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h
new file mode 100644
index 0000000000..21daa2d971
--- /dev/null
+++ b/include/configs/TOP5200.h
@@ -0,0 +1,291 @@
+/*
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.

+ *

+ * modified for TOP5200 by Reinhard Meyer, www.emk-elektronik.de

+ * TOP5200 differences from IceCube:

+ * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks

+ *   bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins

+ * 1 SDRAM/DDRAM Bank up to 256 MB

+ * local VPD I2C Bus is software driven and uses

+ *   GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL

+ * FLASH is located at 0x80000000

+ * Internal regs are at 0xfff00000

+ * Reset jumps to 0x00000100
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC5XXX		1	/* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200		1	/* More exactly a MPC5200 */
+#define CONFIG_TOP5200		1	/* ... on TOP5200 board - we need this for FEC.C */
+
+#define CFG_MPC5XXX_CLKIN	33333333 /* ... running at 33MHz */
+
+#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
+#define BOOTFLAG_WARM		0x02	/* Software reboot	     */
+
+#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
+#define CONFIG_BAUDRATE		9600	/* ... at 9600 bps */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
+
+
+#ifdef CONFIG_EVAL5200		/* PCI is supported with Evaluation board only */
+/*
+ * PCI Mapping:
+ * 0x40000000 - 0x4fffffff - PCI Memory
+ * 0x50000000 - 0x50ffffff - PCI IO Space
+ */
+#  define CONFIG_PCI		1
+#  define CONFIG_PCI_PNP		1
+#  define CONFIG_PCI_SCAN_SHOW	1
+
+#  define CONFIG_PCI_MEM_BUS	0x40000000
+#  define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
+#  define CONFIG_PCI_MEM_SIZE	0x10000000
+
+#  define CONFIG_PCI_IO_BUS	0x50000000
+#  define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
+#  define CONFIG_PCI_IO_SIZE	0x01000000
+
+#  define ADD_PCI_CMD 		CFG_CMD_PCI
+
+#else	/* no Evaluation board */
+
+#  define ADD_PCI_CMD		0  /* no CFG_CMD_PCI */
+
+#endif
+
+/*
+ * Supported commands
+ */
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | ADD_PCI_CMD | \
+				 CFG_CMD_I2C | CFG_CMD_EEPROM)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
+#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* autoboot command */
+#define CONFIG_BOOTARGS		"root=/dev/ram rw"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#undef CFG_IPBSPEED_133   		/* define for 133MHz speed */
+

+/*
+ * I2C configuration
+ */
+/*
+ * EEPROM configuration
+ */
+#define CFG_EEPROM_PAGE_WRITE_BITS	3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	70
+
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_SIZE 0x2000
+

+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_MISC_INIT_R
+

+#undef	CONFIG_HARD_I2C			/* I2C with hardware support */
+#define	CONFIG_SOFT_I2C		1
+

+#if defined (CONFIG_SOFT_I2C)
+#  define SDA0			0x40
+#  define SCL0			0x80
+#  define GPIOE0		*((volatile uchar*)(CFG_MBAR+0x0c00))

+#  define DDR0			*((volatile uchar*)(CFG_MBAR+0x0c08))

+#  define DVO0			*((volatile uchar*)(CFG_MBAR+0x0c0c))

+#  define DVI0			*((volatile uchar*)(CFG_MBAR+0x0c20))

+#  define ODE0			*((volatile uchar*)(CFG_MBAR+0x0c04))

+#  define I2C_INIT		{GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);}
+#  define I2C_READ		((DVI0&SDA0)?1:0)
+#  define I2C_SDA(x)	{if(x)DVO0|=SDA0;else DVO0&=~SDA0;}
+#  define I2C_SCL(x)	{if(x)DVO0|=SCL0;else DVO0&=~SCL0;}
+#  define I2C_DELAY		{udelay(5);}
+#  define I2C_ACTIVE	{DDR0|=SDA0;}
+#  define I2C_TRISTATE	{DDR0&=~SDA0;}
+#  define CFG_I2C_SPEED		100000
+#  define CFG_I2C_SLAVE		0x7F
+#endif
+

+#if defined (CONFIG_HARD_I2C)

+#  define CFG_I2C_MODULE	2		/* Select I2C module #1 or #2 */
+#  define CFG_I2C_SPEED		100000	/* 100 kHz */
+#  define CFG_I2C_SLAVE		0x7F
+#endif

+
+/*
+ * Flash configuration, expect one 16 Megabyte Bank at most
+ */
+#define CFG_FLASH_BASE		0xff000000
+#define CFG_FLASH_SIZE		0x01000000
+#define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks      */
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0)

+
+#define CFG_MAX_FLASH_SECT	256	/* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
+
+#undef CONFIG_FLASH_16BIT	/* Flash is 8-bit */
+
+/*

+ * DRAM configuration - will be read from VPD later... TODO!

+ */

+#if 0

+/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */

+#define	CFG_DRAM_DDR		0

+#define CFG_DRAM_EMODE		0

+#define CFG_DRAM_MODE		0x008D

+#define CFG_DRAM_CONTROL	0x514F0000

+#define CFG_DRAM_CONFIG1	0xC2233A00

+#define CFG_DRAM_CONFIG2	0x88B70004

+#define	CFG_DRAM_TAP_DEL	0x08

+#define CFG_DRAM_RAM_SIZE	0x19

+#endif

+#if 1

+/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */

+#define	CFG_DRAM_DDR		0

+#define CFG_DRAM_EMODE		0

+#define CFG_DRAM_MODE		0x00CD

+#define CFG_DRAM_CONTROL	0x514F0000

+#define CFG_DRAM_CONFIG1	0xD2333A00

+#define CFG_DRAM_CONFIG2	0x8AD70004

+#define	CFG_DRAM_TAP_DEL	0x08

+#define CFG_DRAM_RAM_SIZE	0x19

+#endif

+

+/*
+ * Environment settings
+ */
+#define CFG_ENV_IS_IN_EEPROM	1	/* turn on EEPROM env feature */
+#define CFG_ENV_OFFSET		0x1000
+#define CFG_ENV_SIZE		0x0700
+#define CFG_I2C_EEPROM_ADDR 0x57
+
+/*

+ * VPD settings

+ */

+#define CFG_FACT_OFFSET		0x1800
+#define CFG_FACT_SIZE		0x0800
+#define CFG_I2C_FACT_ADDR	0x57
+

+/*
+ * Memory map

+ *

+ * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000

+ */
+#define CFG_MBAR			0xf0000000	/* DO NOT CHANGE this */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_DEFAULT_MBAR	0x80000000
+
+/* Use SRAM until RAM will be available */
+#define CFG_INIT_RAM_ADDR	MPC5XXX_SRAM
+#define CFG_INIT_RAM_END	MPC5XXX_SRAM_SIZE	/* End of used area in DPRAM */
+
+
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_BASE    TEXT_BASE
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#   define CFG_RAMBOOT		1
+#endif
+
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5XXX_FEC	1
+#define CONFIG_FEC_10MBIT	1		/* Workaround for FEC 100Mbit problem */
+#define	CONFIG_PHY_ADDR		0x1f

+#define	CONFIG_PHY_TYPE		0x79c874
+/*
+ * GPIO configuration:

+ * PSC1,2,3 predefined as UART

+ * PCI disabled

+ * Ethernet 100 with MD
+ */
+#define CFG_GPS_PORT_CONFIG	0x00058444
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	    */
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#  define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
+#else
+#  define CFG_CBSIZE		256	/* Console I/O Buffer Size  */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x00100000	/* memtest works on */
+#define CFG_MEMTEST_END		0x01f00000	/* 1 ... 31 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+
+/*
+ * Various low-level settings
+ */
+#define CFG_HID0_INIT		HID0_ICE | HID0_ICFI
+#define CFG_HID0_FINAL		HID0_ICE
+
+#define CFG_BOOTCS_START	CFG_FLASH_BASE
+#define CFG_BOOTCS_SIZE		CFG_FLASH_SIZE
+#define CFG_BOOTCS_CFG		0x00047801
+#define CFG_CS0_START		CFG_FLASH_BASE
+#define CFG_CS0_SIZE		CFG_FLASH_SIZE
+
+#define CFG_CS_BURST		0x00000000
+#define CFG_CS_DEADCYCLE	0x33333333
+
+#define CFG_RESET_ADDRESS	0x7f000000
+
+#endif /* __CONFIG_H */