Merge branch 'fixes' into cleanups

Conflicts:

	board/atmel/atngw100/atngw100.c
	board/atmel/atstk1000/atstk1000.c
	cpu/at32ap/at32ap700x/gpio.c
	include/asm-avr32/arch-at32ap700x/clk.h
	include/configs/atngw100.h
	include/configs/atstk1002.h
	include/configs/atstk1003.h
	include/configs/atstk1004.h
	include/configs/atstk1006.h
	include/configs/favr-32-ezkit.h
	include/configs/hammerhead.h
	include/configs/mimc200.h

1 files changed, 98 insertions, 101 deletions

diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index f342c7a6db..7ce820518e 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -40,68 +40,68 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0			*/
-#define CFG_FLASH_BASE		0xffe00000	/* start of FLASH		*/
-#define CFG_MONITOR_BASE	0xfffc0000	/* start of monitor		*/
-#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory		*/
-#define	CFG_PCI_MEMSIZE		0x40000000	/* size of mapped pci memory	*/
-#define CFG_PERIPHERAL_BASE	0xe0000000	/* internal peripherals		*/
-#define CFG_ISRAM_BASE		0xc0000000	/* internal SRAM		*/
-#define CFG_PCI_BASE		0xd0000000	/* internal PCI regs		*/
-#define CFG_PCI_MEMBASE1	CFG_PCI_MEMBASE  + 0x10000000
-#define CFG_PCI_MEMBASE2	CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3	CFG_PCI_MEMBASE2 + 0x10000000
-
-
-#define CFG_FPGA_BASE	    (CFG_PERIPHERAL_BASE + 0x08300000)
-#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
+#define CONFIG_SYS_SDRAM_BASE		0x00000000	/* _must_ be 0			*/
+#define CONFIG_SYS_FLASH_BASE		0xffe00000	/* start of FLASH		*/
+#define CONFIG_SYS_MONITOR_BASE	0xfffc0000	/* start of monitor		*/
+#define CONFIG_SYS_PCI_MEMBASE		0x80000000	/* mapped pci memory		*/
+#define	CONFIG_SYS_PCI_MEMSIZE		0x40000000	/* size of mapped pci memory	*/
+#define CONFIG_SYS_PERIPHERAL_BASE	0xe0000000	/* internal peripherals		*/
+#define CONFIG_SYS_ISRAM_BASE		0xc0000000	/* internal SRAM		*/
+#define CONFIG_SYS_PCI_BASE		0xd0000000	/* internal PCI regs		*/
+#define CONFIG_SYS_PCI_MEMBASE1	CONFIG_SYS_PCI_MEMBASE  + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2	CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3	CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+
+
+#define CONFIG_SYS_FPGA_BASE	    (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000)
+#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
 
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in internal SRAM)
  *----------------------------------------------------------------------*/
-#define CFG_TEMP_STACK_OCM  1
-#define CFG_OCM_DATA_ADDR   CFG_ISRAM_BASE
-#define CFG_INIT_RAM_ADDR   CFG_ISRAM_BASE  /* Initial RAM address	*/
-#define CFG_INIT_RAM_END    0x2000	    /* End of used area in RAM	*/
-#define CFG_GBL_DATA_SIZE   128		    /* num bytes initial data	*/
+#define CONFIG_SYS_TEMP_STACK_OCM  1
+#define CONFIG_SYS_OCM_DATA_ADDR   CONFIG_SYS_ISRAM_BASE
+#define CONFIG_SYS_INIT_RAM_ADDR   CONFIG_SYS_ISRAM_BASE  /* Initial RAM address	*/
+#define CONFIG_SYS_INIT_RAM_END    0x2000	    /* End of used area in RAM	*/
+#define CONFIG_SYS_GBL_DATA_SIZE   128		    /* num bytes initial data	*/
 
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
-#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
-#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
+#define CONFIG_SYS_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
+#define CONFIG_SYS_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
 
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
-#undef	CFG_EXT_SERIAL_CLOCK
+#undef	CONFIG_SYS_EXT_SERIAL_CLOCK
 #define CONFIG_BAUDRATE		115200
 #define	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
-#define CFG_BAUDRATE_TABLE  \
+#define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI		1	/* The flash is CFI compatible		*/
+#define CONFIG_SYS_FLASH_CFI		1	/* The flash is CFI compatible		*/
 #define CONFIG_FLASH_CFI_DRIVER	1	/* Use common CFI driver		*/
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
-#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
 
-#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
 
-#define CFG_ENV_SECT_SIZE	0x10000	/* size of one complete sector		*/
-#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define	CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
+#define CONFIG_ENV_SECT_SIZE	0x10000	/* size of one complete sector		*/
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
-#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 
 /*-----------------------------------------------------------------------
  * DDR SDRAM
@@ -109,7 +109,7 @@
 #undef CONFIG_SPD_EEPROM		/* Don't use SPD EEPROM for setup	*/
 #define CONFIG_SDRAM_BANK0	1	/* init onboard DDR SDRAM bank 0	*/
 #undef CONFIG_SDRAM_ECC			/* enable ECC support			*/
-#define CFG_SDRAM_TABLE	{ \
+#define CONFIG_SYS_SDRAM_TABLE	{ \
 		{(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \
 		{(64 << 20),  12, 0x00082001}} /* 64MB mode 2, 12x9(4)	*/
 
@@ -118,22 +118,21 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		100000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs	*/
+#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs	*/
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (PCF8594C)
  *----------------------------------------------------------------------*/
-#define CFG_I2C_EEPROM_ADDR	0x54	/* EEPROM PCF8594C		*/
-#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x54	/* EEPROM PCF8594C		*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 3	/* The Philips PCF8594C has	*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3	/* The Philips PCF8594C has	*/
 					/* 8 byte page write mode using */
 					/* last 3 bits of the address	*/
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	40   /* and takes up to 40 msec */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	40   /* and takes up to 40 msec */
 
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \"run kernelx\" to boot the system;"			\
@@ -197,8 +196,9 @@
 #define CONFIG_BAUDRATE		115200
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_NET_MULTI	1
 #define CONFIG_PHY_ADDR		0x02	/* dummy setting, no EMAC0 used	*/
@@ -212,7 +212,7 @@
 #define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
 #define CONFIG_M88E1111_PHY	1	/* needed for PHY specific setup*/
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
 
 #define CONFIG_NETCONSOLE		/* include NetConsole support	*/
 
@@ -235,43 +235,40 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_FPGA
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
+#undef CONFIG_CMD_NFS
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_ALT_MEMTEST		1	/* Enable more extensive memtest*/
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CONFIG_SYS_ALT_MEMTEST		1	/* Enable more extensive memtest*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
+#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
@@ -279,7 +276,7 @@
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_VERSION_VARIABLE	1	/* include version env variable */
 
-#define CFG_4xx_RESET_TYPE	0x2	/* use chip reset on this board	*/
+#define CONFIG_SYS_4xx_RESET_TYPE	0x2	/* use chip reset on this board	*/
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -289,15 +286,15 @@
 #define CONFIG_PCI			/* include pci support		*/
 #define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
-#define CFG_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CFG_PCI_MEMBASE */
+#define CONFIG_SYS_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
 #define CONFIG_PCI_BOOTDELAY	1       /* enable pci bootdelay variable*/
 
 /* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT		/* let board init pci target    */
-#define CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT		/* let board init pci target    */
+#define CONFIG_SYS_PCI_MASTER_INIT
 
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
-#define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
@@ -305,8 +302,8 @@
 #define CONFIG_FPGA
 #define CONFIG_FPGA_ALTERA
 #define CONFIG_FPGA_CYCLON2
-#define CFG_FPGA_CHECK_CTRLC
-#define CFG_FPGA_PROG_FEEDBACK
+#define CONFIG_SYS_FPGA_CHECK_CTRLC
+#define CONFIG_SYS_FPGA_PROG_FEEDBACK
 #define CONFIG_FPGA_COUNT       1		/* Ich habe 2 ... aber in
 					Reihe geschaltet -> sollte gehen,
 					aufpassen mit Datasize ist jetzt
@@ -315,54 +312,54 @@
 					Mode erklaert ...*/
 
 /* FPGA program pin configuration */
-#define CFG_GPIO_CLK		18	/* FPGA clk pin (cpu output)		*/
-#define CFG_GPIO_DATA		19	/* FPGA data pin (cpu output)		*/
-#define CFG_GPIO_STATUS		20	/* FPGA status pin (cpu input)		*/
-#define CFG_GPIO_CONFIG		21	/* FPGA CONFIG pin (cpu output)		*/
-#define CFG_GPIO_CON_DON	22	/* FPGA CONFIG_DONE pin (cpu input)	*/
+#define CONFIG_SYS_GPIO_CLK		18	/* FPGA clk pin (cpu output)		*/
+#define CONFIG_SYS_GPIO_DATA		19	/* FPGA data pin (cpu output)		*/
+#define CONFIG_SYS_GPIO_STATUS		20	/* FPGA status pin (cpu input)		*/
+#define CONFIG_SYS_GPIO_CONFIG		21	/* FPGA CONFIG pin (cpu output)		*/
+#define CONFIG_SYS_GPIO_CON_DON	22	/* FPGA CONFIG_DONE pin (cpu input)	*/
 
-#define CFG_GPIO_SEL_DPR	14	/* cpu output */
-#define CFG_GPIO_SEL_AVR	15	/* cpu output */
-#define CFG_GPIO_PROG_EN	23	/* cpu output */
+#define CONFIG_SYS_GPIO_SEL_DPR	14	/* cpu output */
+#define CONFIG_SYS_GPIO_SEL_AVR	15	/* cpu output */
+#define CONFIG_SYS_GPIO_PROG_EN	23	/* cpu output */
 
 /*-----------------------------------------------------------------------
  * Definitions for GPIO setup
  *-----------------------------------------------------------------------*/
-#define CFG_GPIO_SHUTDOWN	(0x80000000 >> 6)
-#define CFG_GPIO_SSD_EMPTY	(0x80000000 >> 9)
-#define CFG_GPIO_EREADY		(0x80000000 >> 26)
-#define CFG_GPIO_REV0		(0x80000000 >> 14)
-#define CFG_GPIO_REV1		(0x80000000 >> 15)
+#define CONFIG_SYS_GPIO_SHUTDOWN	(0x80000000 >> 6)
+#define CONFIG_SYS_GPIO_SSD_EMPTY	(0x80000000 >> 9)
+#define CONFIG_SYS_GPIO_EREADY		(0x80000000 >> 26)
+#define CONFIG_SYS_GPIO_REV0		(0x80000000 >> 14)
+#define CONFIG_SYS_GPIO_REV1		(0x80000000 >> 15)
 
 /*-----------------------------------------------------------------------
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE	4
-#define NAND_MAX_CHIPS		CFG_MAX_NAND_DEVICE
-#define CFG_NAND_BASE		0xF0000000	/* NAND FLASH Base Address	*/
-#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE + 0, CFG_NAND_BASE + 2,	\
-				  CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 }
-#define CFG_NAND_QUIET_TEST	1	/* don't warn upon unknown NAND flash	*/
+#define CONFIG_SYS_MAX_NAND_DEVICE	4
+#define NAND_MAX_CHIPS		CONFIG_SYS_MAX_NAND_DEVICE
+#define CONFIG_SYS_NAND_BASE		0xF0000000	/* NAND FLASH Base Address	*/
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2,	\
+				  CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
+#define CONFIG_SYS_NAND_QUIET_TEST	1	/* don't warn upon unknown NAND flash	*/
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
-#define CFG_FLASH		CFG_FLASH_BASE
+#define CONFIG_SYS_FLASH		CONFIG_SYS_FLASH_BASE
 
 /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
-#define CFG_EBC_PB0AP		0x92015480
-#define CFG_EBC_PB0CR		(CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB0AP		0x92015480
+#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */
 
 /* Memory Bank 1 (NAND-FLASH) initialization					*/
-#define CFG_EBC_PB1AP		0x01840380	/* TWT=3			*/
-#define CFG_EBC_PB1CR		(CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB1AP		0x01840380	/* TWT=3			*/
+#define CONFIG_SYS_EBC_PB1CR		(CONFIG_SYS_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*
  * Internal Definitions