powerpc: remove cogent_8xx, cogent_mpc8260 board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Murray Jensen <Murray.Jensen@csiro.au>

1 files changed, 0 insertions, 392 deletions

diff --git a/include/configs/cogent_mpc8260.h b/include/configs/cogent_mpc8260.h
deleted file mode 100644
index 02b25c6444..0000000000
--- a/include/configs/cogent_mpc8260.h
+++ /dev/null
@@ -1,392 +0,0 @@
-/*
- * (C) Copyright 2000
- * Murray Jensen <Murray.Jensen@cmst.csiro.au>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Config header file for Cogent platform using an MPC8xx CPU module
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU	*/
-#define CONFIG_COGENT		1	/* using Cogent Modular Architecture */
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff00000
-
-#define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
-#define	CONFIG_MISC_INIT_R		/* Use misc_init_r()		*/
-
-/* Cogent Modular Architecture options */
-#define CONFIG_CMA282		1	/* ...on a CMA282 CPU module	*/
-#define CONFIG_CMA111		1	/* ...on a CMA111 motherboard	*/
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#define	CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#undef	CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef	CONFIG_CONS_NONE		/* define if console on something else*/
-#define CONFIG_CONS_INDEX	1	/* which serial channel for console */
-#undef	CONFIG_CONS_USE_EXTC		/* SMC/SCC use ext clock not brg_clk */
-#define	CONFIG_CONS_EXTC_RATE	3686400	/* SMC/SCC ext clk rate in Hz */
-#define	CONFIG_CONS_EXTC_PINSEL	0	/* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC	*/
-#undef	CONFIG_ETHER_ON_FCC		/* define if ether on FCC	*/
-#define	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_INDEX	1	/* which channel for ether	*/
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#define CONFIG_8260_CLKIN	66666666	/* in Hz */
-
-#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
-#define CONFIG_BAUDRATE		230400
-#else
-#define CONFIG_BAUDRATE		9600
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_KGDB
-
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-
-#ifdef DEBUG
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-#define CONFIG_BOOTCOMMAND	"bootm 04080000 04200000" /* autoboot command*/
-
-#define CONFIG_BOOTARGS		"root=/dev/ram rw"
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
-#undef	CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
-#undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX	2	/* which serial channel for kgdb */
-#define	CONFIG_KGDB_USE_EXTC		/* SMC/SCC use ext clock not brg_clk */
-#define	CONFIG_KGDB_EXTC_RATE	3686400	/* serial ext clk rate in Hz */
-#define	CONFIG_KGDB_EXTC_PINSEL	0	/* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/
-# if defined(CONFIG_KGDB_NONE) || defined(CONFIG_KGDB_USE_EXTC)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port at */
-# else
-#define CONFIG_KGDB_BAUDRATE	9600	/* speed to run kgdb serial port at */
-# endif
-#endif
-
-#undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x01c00000	/* 4 ... 28 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Low Level Cogent settings
- * if CONFIG_SYS_CMA_CONS_SERIAL is defined, make sure the 8260 CPM serial is not.
- * also, make sure CONFIG_CONS_INDEX is still defined - the index will be
- * 1 for serialA, 2 for serialB, 3 for ser2A, 4 for ser2B
- * (second 2 for CMA120 only)
- */
-#define CONFIG_SYS_CMA_MB_BASE		0x00000000	/* base of m/b address space */
-
-#include <configs/cogent_common.h>
-
-#ifdef CONFIG_CONS_NONE
-#define CONFIG_SYS_CMA_CONS_SERIAL	/* use Cogent motherboard serial for console */
-#endif
-#define CONFIG_SYS_CMA_LCD_HEARTBEAT	/* define for sec rotator in lcd corner */
-#define CONFIG_SHOW_ACTIVITY
-
-#if (CMA_MB_CAPS & CMA_MB_CAP_FLASH)
-/*
- * flash exists on the motherboard
- * set these four according to TOP dipsw:
- * TOP on  => ..._FLLOW_...	(boot EPROM space is high so FLASH is low )
- * TOP off => ..._FLHIGH_...	(boot EPROM space is low  so FLASH is high)
- */
-#define CMA_MB_FLASH_EXEC_BASE	CMA_MB_FLLOW_EXEC_BASE
-#define CMA_MB_FLASH_EXEC_SIZE	CMA_MB_FLLOW_EXEC_SIZE
-#define CMA_MB_FLASH_RDWR_BASE	CMA_MB_FLLOW_RDWR_BASE
-#define CMA_MB_FLASH_RDWR_SIZE	CMA_MB_FLLOW_RDWR_SIZE
-#endif
-#define CMA_MB_FLASH_BASE	CMA_MB_FLASH_EXEC_BASE
-#define CMA_MB_FLASH_SIZE	CMA_MB_FLASH_EXEC_SIZE
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#define CONFIG_SYS_HRCW_MASTER	(HRCW_EBM|HRCW_BPS10|HRCW_L2CPC10|HRCW_DPPC11|\
-			 HRCW_ISB100|HRCW_MMR11|HRCW_MODCK_H0101)
-/* no slaves so just duplicate the master hrcw */
-#define CONFIG_SYS_HRCW_SLAVE1	CONFIG_SYS_HRCW_MASTER
-#define CONFIG_SYS_HRCW_SLAVE2	CONFIG_SYS_HRCW_MASTER
-#define CONFIG_SYS_HRCW_SLAVE3	CONFIG_SYS_HRCW_MASTER
-#define CONFIG_SYS_HRCW_SLAVE4	CONFIG_SYS_HRCW_MASTER
-#define CONFIG_SYS_HRCW_SLAVE5	CONFIG_SYS_HRCW_MASTER
-#define CONFIG_SYS_HRCW_SLAVE6	CONFIG_SYS_HRCW_MASTER
-#define CONFIG_SYS_HRCW_SLAVE7	CONFIG_SYS_HRCW_MASTER
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		CMA_MB_RAM_BASE
-#ifdef CONFIG_CMA302
-#define CONFIG_SYS_FLASH_BASE		CMA_MB_SLOT2_BASE	/* cma302 in slot 2 */
-#else
-#define CONFIG_SYS_FLASH_BASE		CMA_MB_FLASH_BASE	/* flash on m/b */
-#endif
-#define	CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Mem map for Linux*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max num of memory banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	67	/* max num of sects on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Flash Erase Timeout (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		CONFIG_SYS_FLASH_BASE /* Addr of Environment Sector */
-#ifdef CONFIG_CMA302
-#define	CONFIG_ENV_SIZE		0x1000	/* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE	(512*1024) /* see README - env sect real size */
-#else
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector */
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPU		*/
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value*/
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers			 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT	(HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
-				HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL	(HID0_ICE|HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2	0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register					 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR		RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration					 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR		BCR_EBM
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				 4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DPPC11|SIUMCR_L2CPC10|SIUMCR_MMR11)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				 4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control			 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC	(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control					 9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR	(SCCR_DFBRG01)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration				13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR	0
-
-#if defined(CONFIG_CMA282)
-
-/*
- * Init Memory Controller:
- *
- * According to the Cogent manual, only CS0 and CS2 are used - CS0 for EPROM
- * and CS2 for (optional) local bus RAM on the CPU module.
- *
- * Note the motherboard address space (256 Mbyte in size) is connected
- * to the 60x Bus and is located starting at address 0. The Hard Reset
- * Configuration Word should put the 60x Bus into External Bus Mode, since
- * we dont set up any memory controller maps for it (see BCR[EBM], 4-26).
- *
- * (the *_SIZE vars must be a power of 2)
- */
-
-#define CONFIG_SYS_CMA_CS0_BASE	CONFIG_SYS_TEXT_BASE	/* EPROM */
-#define CONFIG_SYS_CMA_CS0_SIZE	(1 << 20)
-#if 0
-#define CONFIG_SYS_CMA_CS2_BASE	0x10000000	/* Local Bus SDRAM */
-#define CONFIG_SYS_CMA_CS2_SIZE	(16 << 20)
-#endif
-
-/*
- * CS0 maps the EPROM on the cpu module
- * Set it for 10 wait states, address CONFIG_SYS_MONITOR_BASE and size 1M
- *
- * Note: We must have already transferred control to the final location
- * of the EPROM before these are used, because when BR0/OR0 are set, the
- * mirror of the eprom at any other addresses will disappear.
- */
-
-/* base address = CONFIG_SYS_CMA_CS0_BASE, 16-bit, no parity, r/o, gpcm (60x bus) */
-#define CONFIG_SYS_BR0_PRELIM	((CONFIG_SYS_CMA_CS0_BASE&BRx_BA_MSK)|BRx_PS_16|BRx_WP|BRx_V)
-/* mask size CONFIG_SYS_CMA_CS0_SIZE, csneg 1/4 early, adr-to-cs 1/2, 10-wait states */
-#define CONFIG_SYS_OR0_PRELIM	(P2SZ_TO_AM(CONFIG_SYS_CMA_CS0_SIZE)|\
-				ORxG_CSNT|ORxG_ACS_DIV2|ORxG_SCY_10_CLK)
-
-/*
- * CS2 enables the Local Bus SDRAM on the CPU Module
- *
- * Will leave this unset for the moment, because a) my CPU module has no
- * SDRAM installed (it is optional); and b) it will require programming
- * one of the UPMs in SDRAM mode - not a trivial job, and hard to get right
- * if you can't test it.
- */
-
-#if 0
-/* base address = CONFIG_SYS_CMA_CS2_BASE, 32-bit, no parity, ??? */
-#define CONFIG_SYS_BR0_PRELIM	((CONFIG_SYS_CMA_CS2_BASE&BRx_BA_MSK)|BRx_PS_32|/*???*/|BRx_V)
-/* mask size CONFIG_SYS_CMA_CS2_SIZE, CS time normal, ??? */
-#define CONFIG_SYS_OR2_PRELIM	((~(CONFIG_SYS_CMA_CS2_SIZE-1)&ORx_AM_MSK)|/*???*/)
-#endif
-
-#endif
-#endif	/* __CONFIG_H */