ppc4xx: Unify AMCC's board config files (part 2/3)

This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:

include/configs/amcc-common.h

This header now includes all common configuration options/defines which
are removed from the board specific headers.

The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.

Signed-off-by: Stefan Roese <sr@denx.de>

1 files changed, 14 insertions, 133 deletions

diff --git a/include/configs/luan.h b/include/configs/luan.h
index 41999d32f9..805cc59b30 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -37,6 +37,12 @@
 #define CONFIG_440		1
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		luan
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
@@ -44,11 +50,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc  */
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE	        0x00000000	/* MUST be zero */
-
 #define CFG_LARGE_FLASH		0xffc00000	/* 4MB flash address CS0 */
 #define CFG_SMALL_FLASH		0xff900000	/* 1MB flash address CS2 */
 #define CFG_SRAM_BASE		0xff800000	/* 1MB SRAM  address CS2 */
@@ -87,13 +88,8 @@
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CFG_EXT_SERIAL_CLOCK	11059200 /* external 11.059MHz clk */
-#define CONFIG_BAUDRATE		115200
-#undef  CONFIG_SERIAL_MULTI
 #undef  CONFIG_UART1_CONSOLE		/* define if you want console on UART1 */
 
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -138,10 +134,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -150,61 +143,22 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=luan\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=$(serverip):$(rootpath)\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs $(bootargs) "				\
-		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
-		":$(hostname):$(netdev):off panic=1\0"			\
-	"addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm $(kernel_addr)\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm $(kernel_addr) $(ramdisk_addr)\0"		\
-	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/luan/uImage\0"				\
+/*
+ * Default environment variables
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc100000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/luan/u-boot.bin\0"			\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_HAS_ETH0
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
-
 #ifdef DEBUG
 #define CONFIG_PANIC_HANG
 #else
@@ -212,60 +166,11 @@
 #endif
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on	        */
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000 /* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-#undef  CONFIG_LYNXKDI			/* support kdi files            */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -286,28 +191,4 @@
 
 #endif
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */