lx2160aqds : Add support for LX2160AQDS platform

LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.

Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

1 files changed, 140 insertions, 0 deletions

diff --git a/include/configs/lx2160aqds.h b/include/configs/lx2160aqds.h
new file mode 100644
index 0000000000..662e601f0f
--- /dev/null
+++ b/include/configs/lx2160aqds.h
@@ -0,0 +1,140 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2018-2019 NXP
+ */
+
+#ifndef __LX2_QDS_H
+#define __LX2_QDS_H
+
+#include "lx2160a_common.h"
+
+/* Qixis */
+#define QIXIS_XMAP_MASK			0x07
+#define QIXIS_XMAP_SHIFT		5
+#define QIXIS_RST_CTL_RESET_EN		0x30
+#define QIXIS_LBMAP_DFLTBANK		0x00
+#define QIXIS_LBMAP_ALTBANK		0x20
+#define QIXIS_LBMAP_QSPI		0x00
+#define QIXIS_RCW_SRC_QSPI		0xff
+#define QIXIS_RST_CTL_RESET		0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SD
+#define QIXIS_RCW_SRC_SD		0x08
+#define NON_EXTENDED_DUTCFG
+#define QIXIS_SDID_MASK			0x07
+#define QIXIS_ESDHC_NO_ADAPTER		0x7
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_100		0x0
+#define QIXIS_SYSCLK_125		0x1
+#define QIXIS_SYSCLK_133		0x2
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_100		0x0
+#define QIXIS_DDRCLK_125		0x1
+#define QIXIS_DDRCLK_133		0x2
+
+#define BRDCFG4_EMI1SEL_MASK		0xF8
+#define BRDCFG4_EMI1SEL_SHIFT		3
+#define BRDCFG4_EMI2SEL_MASK		0x07
+#define BRDCFG4_EMI2SEL_SHIFT		0
+
+/* VID */
+
+#define I2C_MUX_CH_VOL_MONITOR		0xA
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR		0x63
+#define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF	0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT	3
+#define CONFIG_VID_FLS_ENV		"lx2160aqds_vdd_mv"
+#define CONFIG_VID
+
+/* The lowest and highest voltage allowed*/
+#define VDD_MV_MIN			775
+#define VDD_MV_MAX			925
+
+/* PM Bus commands code for LTC3882*/
+#define PMBUS_CMD_PAGE                  0x0
+#define PMBUS_CMD_READ_VOUT             0x8B
+#define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
+#define PMBUS_CMD_VOUT_COMMAND          0x21
+#define PWM_CHANNEL0                    0x0
+
+#define CONFIG_VOL_MONITOR_LTC3882_SET
+#define CONFIG_VOL_MONITOR_LTC3882_READ
+
+/* RTC */
+#define CONFIG_SYS_RTC_BUS_NUM		0
+#define I2C_MUX_CH_RTC			0xB
+
+/*
+ * MMC
+ */
+#ifdef CONFIG_MMC
+#ifndef __ASSEMBLY__
+u8 qixis_esdhc_detect_quirk(void);
+#endif
+#define CONFIG_ESDHC_DETECT_QUIRK  qixis_esdhc_detect_quirk()
+#endif
+
+/* MAC/PHY configuration */
+#if defined(CONFIG_FSL_MC_ENET)
+#define CONFIG_MII
+#define CONFIG_ETHPRIME		"DPMAC17@rgmii-id"
+
+#define AQ_PHY_ADDR1		0x00
+#define AQ_PHY_ADDR2		0x01
+#define AQ_PHY_ADDR3		0x02
+#define AQ_PHY_ADDR4		0x03
+
+#define CORTINA_NO_FW_UPLOAD
+#define CORTINA_PHY_ADDR1	0x0
+
+#define INPHI_PHY_ADDR1		0x0
+#define INPHI_PHY_ADDR2		0x1
+
+#define RGMII_PHY_ADDR1		0x01
+#define RGMII_PHY_ADDR2		0x02
+
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM		0
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	EXTRA_ENV_SETTINGS			\
+	"lx2160aqds_vdd_mv=800\0"		\
+	"BOARD=lx2160aqds\0"			\
+	"xspi_bootcmd=echo Trying load from flexspi..;"		\
+		"sf probe 0:0 && sf read $load_addr "		\
+		"$kernel_start $kernel_size ; env exists secureboot &&"	\
+		"sf read $kernelheader_addr_r $kernelheader_start "	\
+		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
+		" bootm $load_addr#$BOARD\0"			\
+	"sd_bootcmd=echo Trying load from sd card..;"		\
+		"mmcinfo; mmc read $load_addr "			\
+		"$kernel_addr_sd $kernel_size_sd ;"		\
+		"env exists secureboot && mmc read $kernelheader_addr_r "\
+		"$kernelhdr_addr_sd $kernelhdr_size_sd "	\
+		" && esbc_validate ${kernelheader_addr_r};"	\
+		"bootm $load_addr#$BOARD\0"
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LX2_QDS_H */