Merge remote-tracking branch 'u-boot-imx/master'

1 files changed, 78 insertions, 8 deletions

diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
index 4e1e6bc0a8..dffb744c3d 100644
--- a/include/configs/mx28evk.h
+++ b/include/configs/mx28evk.h
@@ -184,6 +184,9 @@
 #define	CONFIG_EHCI_MXS_PORT 1
 #define	CONFIG_EHCI_IS_TDI
 #define	CONFIG_USB_STORAGE
+#define	CONFIG_USB_HOST_ETHER
+#define	CONFIG_USB_ETHER_ASIX
+#define	CONFIG_USB_ETHER_SMSC95XX
 #endif
 
 /* I2C */
@@ -199,6 +202,7 @@
 #ifdef CONFIG_CMD_SPI
 #define CONFIG_HARD_SPI
 #define CONFIG_MXS_SPI
+#define CONFIG_MXS_SPI_DMA_ENABLE
 #define CONFIG_SPI_HALF_DUPLEX
 #define CONFIG_DEFAULT_SPI_BUS		2
 #define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0
@@ -235,7 +239,6 @@
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_BOOTDELAY	3
 #define CONFIG_BOOTFILE	"uImage"
-#define CONFIG_BOOTCOMMAND	"run bootcmd_net"
 #define CONFIG_LOADADDR	0x42000000
 #define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
 #define CONFIG_OF_LIBFDT
@@ -244,13 +247,80 @@
  * Extra Environments
  */
 #define CONFIG_EXTRA_ENV_SETTINGS \
-	"console_fsl=console=ttyAM0" \
-	"console_mainline=console=ttyAMA0" \
-	"netargs=setenv bootargs console=${console_mainline}" \
+	"update_nand_full_filename=u-boot.nand\0" \
+	"update_nand_firmware_filename=u-boot.sb\0"	\
+	"update_sd_firmware_filename=u-boot.sd\0" \
+	"update_nand_firmware_maxsz=0x100000\0"	\
+	"update_nand_stride=0x40\0"	/* MX28 datasheet ch. 12.12 */ \
+	"update_nand_count=0x4\0"	/* MX28 datasheet ch. 12.12 */ \
+	"update_nand_get_fcb_size="	/* Get size of FCB blocks */ \
+		"nand device 0 ; " \
+		"nand info ; " \
+		"setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
+		"setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
+	"update_nand_full="		    /* Update FCB, DBBT and FW */ \
+		"if tftp ${update_nand_full_filename} ; then " \
+		"run update_nand_get_fcb_size ; " \
+		"nand scrub -y 0x0 ${filesize} ; " \
+		"nand write.raw ${loadaddr} 0x0 ${update_nand_fcb} ; " \
+		"setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
+		"setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
+		"nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
+		"fi\0" \
+	"update_nand_firmware="		/* Update only firmware */ \
+		"if tftp ${update_nand_firmware_filename} ; then " \
+		"run update_nand_get_fcb_size ; " \
+		"setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
+		"setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; " \
+		"setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
+		"nand erase ${fcb_sz} ${fw_sz} ; " \
+		"nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \
+		"nand write ${loadaddr} ${fw_off} ${filesize} ; " \
+		"fi\0" \
+	"update_sd_firmware="		/* Update the SD firmware partition */ \
+		"if mmc rescan ; then "	\
+		"if tftp ${update_sd_firmware_filename} ; then " \
+		"setexpr fw_sz ${filesize} / 0x200 ; "	/* SD block size */ \
+		"setexpr fw_sz ${fw_sz} + 1 ; "	\
+		"mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
+		"fi ; "	\
+		"fi\0" \
+	"script=boot.scr\0"	\
+	"uimage=uImage\0" \
+	"console_fsl=ttyAM0\0" \
+	"console_mainline=ttyAMA0\0" \
+	"mmcdev=0\0" \
+	"mmcpart=2\0" \
+	"mmcroot=/dev/mmcblk0p3 rw\0" \
+	"mmcrootfstype=ext3 rootwait\0"	\
+	"mmcargs=setenv bootargs console=${console_mainline},${baudrate} " \
+		"root=${mmcroot} " \
+		"rootfstype=${mmcrootfstype}\0"	\
+	"loadbootscript="  \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; "	\
+		"source\0" \
+	"loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; "	\
+		"bootm\0" \
+	"netargs=setenv bootargs console=${console_mainline},${baudrate} " \
 		"root=/dev/nfs " \
-		"ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
-	"bootcmd_net=echo Booting from net ...; " \
-		"run netargs; " \
-		"dhcp ${uimage}; bootm\0" \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; "	\
+		"dhcp ${uimage}; bootm\0"
+
+#define CONFIG_BOOTCOMMAND \
+	"if mmc rescan ${mmcdev}; then " \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run loaduimage; then " \
+				"run mmcboot; " \
+			"else run netboot; " \
+			"fi; " \
+		"fi; " \
+	"else run netboot; fi"
 
 #endif /* __MX28EVK_CONFIG_H__ */